KS0369 EASY plug 4-Digit LED Display

From Keyestudio Wiki
Jump to: navigation, search
Keyestudio EASY plug 4-Digit LED Display


Introduction

This is a 4-digit 0.36’’ Common Anode LED display module, a 12-pin display module with score points.
The driver chip used in the matrices is TM1637, using only two signal cables to make the microcontroller control the 4-digit LED display.
The four pins of LED display are GND、VCC、DIO、CLK. (GND is ground, VCC is for power supply, DIO is data IO pin, CLK is clock signal pin.)
The module pins are extended into Registered jack, so you can easily connect it to EASY Plug control board using a RJ11 cable.
Note: this module should be used together with EASY plug control board.

Parameters

  • Operating Voltage: DC5V
  • Operating Temperature Range: -40~+85℃
  • Property: ROHS


Technical Details

  • Dimensions: 50mm*23mm*18mm
  • Weight: 9g


Connect It Up

Connect the EASY Plug 4-Digit LED display to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.
Note: before compile the code, do remember to place the necessary libraries inside the libraries directory of Arduino IDE.
You can download the libraries from the link:
https://drive.google.com/open?id=1F7LbjsK0600YRM4OClhy8xd-BGc1Gmc2

#include "TM1637.h"
#define CLK 4//pins definitions for TM1637 and can be changed to other ports       
#define DIO 3
TM1637 tm1637(CLK,DIO);
void setup()
{
  tm1637.init();
  tm1637.set(BRIGHT_TYPICAL);//BRIGHT_TYPICAL = 2,BRIGHT_DARKEST = 0,BRIGHTEST = 7;
}
void loop()
{
  //int8_t NumTab[] = {0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15};//0~9,A,b,C,d,E,F
  int8_t NumTab[] = {0,1,2,3,4,5,6,7,8,9};//0~9,A,b,C,d,E,F
  int8_t ListDisp[4];
  unsigned char i = 0;
  unsigned char count = 0;
  delay(150);
  while(1)
  {
    i = count;
    count ++;
    if(count == sizeof(NumTab)) count = 0;
    for(unsigned char BitSelect = 0;BitSelect < 4;BitSelect ++)
    {
      ListDisp[BitSelect] = NumTab[i];
      i ++;
      if(i == sizeof(NumTab)) i = 0;
    
    tm1637.display(0,ListDisp[0]);
    tm1637.display(1,ListDisp[0]); 
    tm1637.display(2,ListDisp[0]);
    tm1637.display(3,ListDisp[0]);
    tm1637.point(POINT_ON);
    delay(100);
    }
  }
}


What You Should See

After uploading the code, you should see the 4-digit LED display jump the number from 0 to 9.
thumb


Resources

Download the PDF:
https://drive.google.com/open?id=1QZJEQ-D9PNo7Vbr0Mdrw_GcWXVwe_kYs

Download the Code:
https://drive.google.com/open?id=1Vd35rEqSXbxxTWSNfoAdTiSCp91sKQOQ

Download the libraries:
https://drive.google.com/open?id=1F7LbjsK0600YRM4OClhy8xd-BGc1Gmc2



Buy from