Ks0093 Keyestudio 3D Printer Kit MKS base V1.2 + 5x 8825 + LCD 12864 smart Controller
- 1 Keyestudio 3D Printer Kit MKS base V1.2 + 5x 8825 + LCD 12864 smart Controller
- 2 Description
- 3 Package list:
- 4 Connection Method
- 5 Using Method
- 6 Application of Slicer Software
- 7 Resources
- 8 Buy from
Keyestudio 3D Printer Kit MKS base V1.2 + 5x 8825 + LCD 12864 smart Controller
1.The new MKS Base 1.2 3D Printer Controller board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for your Reprap 3D Printer.
2. LCD 12864 Smart Controller
It contains a SD-Card reader. You can easy connect it to your Ramps board using the ""smart adapter"" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
3. The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).
1pc MKS base V1.2
1pc Lcd12864 smart Controller
5pcs 8825 stepper driver
1pcs USB 2.0 cable
Install Diver Software
A. Connect the main board with computer, and then right click “Computer” to enter “Device Manage”.
B. Double click “Other devices”, appearing “USB Serial Port”.
Then, right click “USB Serial Port” and select “Update Driver Software” to install driver software.
After that, select “Browse my computer for driver software” to find the file.
Browse to search for driver software.
After your driver software updated, click “Close” to finish.
Install development environment software IDE
Double click arduino-1.5.6-r2-windows to start.
Select “I Agree”to accept license agreement.
Select components to install and click “Next”.
Click “Browse” and select another folder. Click “Install” to start the installation.
Finally, wait for a few minutes to finish.
Install Firmware for Main Board
A. You must close Arduino IDE firstly, and then place three libraries LiquidCrystal, SPI and U8glib from Marlin_Marlin_v1→ArduinoAddons→Arduino_1.x.x→libraries into Arduino/libraries.
B. Enter Marlin_Marlin_RAMPS_2004_Ver1 this folder, double click Marlin_Marlin_RAMPS_2004_Ver1.ino this file, finally click “Tools” to set “Board”and “Port”.
After verifying, write code.
Install Slicer Software Repetier-Host
Application of Slicer Software
E. After slicing, go to Preview→G-Code Editor, copy G-Code to SD card, and then insert the card into the main board. It is time to kick off the print! Though the LCD screen go to : Print from SD→Desired File. Or you can connect your 3D printer to computer using a USB cable to start the print.
G. We just introduce a simple method about printing. Thanks to selling only main board by us, you should design your own structure and outlook of your 3D printer, and you should also set your own configuration to meet your need. After you assembling your printer, the printer need to be leveled, so you can make some setup in Preview and Manual Control, and surf the internet for further information.
H. We have a G-Code to test the main board. Power it on, open limit switch and stepper motor, drive three motors; put a Fnbduino.gco file to Preview, click Start Print, if the motors rotate, X/Y/Z value in Manual Control changes, the main board works as shown below:
Download the PDF:
Official Website: http://www.keyestudio.com/ks0093.html