Ks0094 Arduino CNC kit / CNC Shield V2.0 +keyestudio Uno R3+3pcs A4988 Driver / GRBL Compatible

From Keyestudio Wiki
Jump to navigation Jump to search

Arduino CNC kit / CNC Shield V2.0 +keyestudio V4.0+3pcs A4988 driver / GRBL compatible


thumb


Introduction

Keyestudio CNC Shield V2.0 can be used as driver expansion board for engraving machines. It has in total 3 channel slots for A4988 stepper motor driver modules (not included) for driving 3 channel of stepper motors. Each channel of stepper motor only needs 2 IO ports, which means 6 IO ports is sufficient to manage 3 stepper motors. This shield can make quick work for managing stepper motors in your project.


CNC Shield V2.0 features

  • Keyestudio CNC Shield Version 2.0
  • GRBL 0.8c compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
  • 3-Axis support (X, Y, Z , )
  • 2 x End stops for each axis (6 in total)
  • Spindle enable and direction
  • Coolant enable
  • Uses removable A4988 compatible stepper drivers. (A4988, DRV8825 and others)
  • Jumpers to set the Micro-Stepping for the stepper drivers. (Some drivers like the DRV8825 can do up to 1/32 micro-stepping )
  • Compact design.
  • Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
  • Runs on 12V DC.


Kit list

  • 1x CNC Shield V2.0
  • 1x keyestudio V4.0 board
  • 3x A4988 driver
  • 1x USB cable


Connection Diagram


thumb


Adjusting the drive current

In the kit, we have applied the A4988 drive module to drive stepper motor. When using, you can turn the potentiometer on the drive module to adjust the drive current.
The specific method please refer to the website link below:
https://wiki.keyestudio.com/Ks0281_Keyestudio_Reprap_Stepper_Motor_Driver


Install Driver Software and Development Environment Software IDE

Install Diver Software

For different operating system, there may be slight difference in installation method. Below is an example in WIN 7.
When you connect V4.0 board to your computer the first time, right click “Computer” —>“Properties”—> “Device manager”, you can see “Unknown devices”.

thumb
Click “Unknown devices”, select “Update Driver software”.
thumb

In this page, click “Browse my computer for driver software”.
thumb
Find the “drivers” file.
thumb
Click “Next”; select “Install this driver software anyway” to begin the installation.
thumb
Installation completed; click “Close”.
thumb
After driver is installed, go to “Device manager” again. right click “Computer” —> “Properties”—> “Device manager”, you can see device as below figure shows, also the correct Com port.
thumb


Install development environment software IDE

Double click arduino-1.5.6-r2-windows to start. Select “I Agree”to accept license agreement.
thumb
Select components to install and click “Next”.
thumb
Click “Browse” and select another folder. Click “Install” to start the installation.
thumb
Finally, wait for a few minutes to finish.
thumb


Using Method

Test Main Board

First, write below code in IDE to test whether main board, shield and three motors work normally.

Explanation
1. If you properly reduce the value 800 in delayMicroseconds(800) to increase the frequency of input PWM signal, you can increase the rotation speed of stepper motor. The change of value cannot be too much or the motor will stop moving.
2. Rotate the knob on A4988, you can adjust the output current of the motors to change the torque.

Code

#define EN        8       // stepper motor enable, low level effective
#define X_DIR     5       //X axis, stepper motor direction control 
#define Y_DIR     6       //y axis, stepper motor direction control
#define Z_DIR     7       //zaxis, stepper motor direction control
#define X_STP     2       //x axis, stepper motor control
#define Y_STP     3       //y axis, stepper motor control
#define Z_STP     4       //z axis, stepper motor control
/*
// Function: step   -control the direction and number of steps of the stepper motor
// Parameter: dir  -direction control, dirPin corresponds to DIR pin, stepperPin correspomds to 


step pin, steps is the number of steps.
// no return value
*/
void step(boolean dir, byte dirPin, byte stepperPin, int steps)
{
  digitalWrite(dirPin, dir);
  delay(50);
  for (int i = 0; i < steps; i++) {
    digitalWrite(stepperPin, HIGH);
    delayMicroseconds(800);  
    digitalWrite(stepperPin, LOW);
    delayMicroseconds(800);  
  }
}
void setup(){// set the IO pins for the stepper motors as output 
  pinMode(X_DIR, OUTPUT); pinMode(X_STP, OUTPUT);
  pinMode(Y_DIR, OUTPUT); pinMode(Y_STP, OUTPUT);
  pinMode(Z_DIR, OUTPUT); pinMode(Z_STP, OUTPUT);
  pinMode(EN, OUTPUT);
  digitalWrite(EN, LOW);
}
void loop(){
  step(false, X_DIR, X_STP, 3200); // x axis motor rotates CCW for 1 circle, as in 200 steps
  step(false, Y_DIR, Y_STP, 3200); // y axis motor rotates CCW for 1 circle, as in 200 steps
  step(false, Z_DIR, Z_STP, 3200); // z axis motor rotates CCW for 1 circle, as in 200 steps
  delay(1000);
  step(true, X_DIR, X_STP, 3200); // X axis motor rotates CW for 1 circle, as in 200 steps
  step(true, Y_DIR, Y_STP, 3200); // y axis motor rotates CW for 1 circle, as in 200 steps
  step(true, Z_DIR, Z_STP, 3200); // z axis motor rotates CW for 1 circle, as in 200 steps
  delay(1000);
}


Install Firmware and Grbl Controller

a. Write test program to keyestudio REV4
copy the folder GRBL_ Arduino_Library_keyes in the data packet and paste it into to the folder libraries, in your Arduino IDE document installation.

Code

#include <grblmain.h>
void setup(){
startGrbl();
}
void loop(){}
//

Compile the code above to keyestudio REV4 via IDE.

b. Install GrblController361 Software
Grbl Controller is a piece of software which is used to send GCode to CNC Machines. Run Grbl Controller361 Setup in your installation packet, the interface below will come out:
Click Next to continue.
thumb

For a license agreement, please check I accept the agreement and click Next.
thumb

When you are ready to continue with Setup, click Next.
thumb

To continue, click Next. If you would like to select a different folder to install, click Browse.
thumb

To continue, click Next. If you would like to select a different folder to place program’s shortcuts, click Browse.
thumb

Select the additional tasks you would like Setup to perform while installing Grbl Controller, then click Next.
thumb

Click Install to continue with the installation.
thumb

Click Next.
thumb

At last, click ”Finish” to finish the installation.
thumb

c. Test G-Code on Grbl Controller
Power the main board using a USB cable and connect correctly all your external devices, then run Grbl Controller.
Choose Port name the same as IDE COM port and click “Open” to open the series port, connecting CNC Machines with computer.

thumb

After opening the series port, the “Open” button change into “Close/Reset” and get red!
At this time you can click the X axis、Y axis、Z axis as shown in below diagram to adjust the motion direction of motors.

thumb

Note: after adjusting the axies, before beginning G-Code file, you must close and open again .
Now, it is time to have a try! Click ”Choose file” to choose one G-Code file named cn. to test in the data packet for a beginner, and the interface will come out:
GrblController.
thumb
Click “Begin” , and you can see how the motors move on coordinates.


Resources

Arduino IDE Download
https://www.arduino.cc/en/Main/Donate

Download driver, G-Code, Grbl Controller361 setup and library : https://fs.keyestudio.com/KS0094



Buy from

Offical Website https://www.keyestudio.com/free-shipping-keyestudio-cnc-kit-for-arduino-cnc-shield-v2uno-r33xa4988-grbl-compatible-p0289-p0289.html