Search results
Jump to navigation
Jump to search
- ...eral modules together. And extra modules can be connected to the expansion board for easier control.<br> ...er experience on intelligence and convenience of gesture control, multiple Arduino C language projects are prepared for you. In these projects, we will start3 KB (445 words) - 09:03, 20 March 2023
- In the experiments, you might often use UNO R3 control board and several sensor modules. If the interfaces of power output is not enough ...ly solve that problem. This shield is fully compatible with UNO R3 control board, so you can easily stack it onto UNO R3 for use.<br>3 KB (537 words) - 10:15, 29 April 2021
- ...aunch this new pyroelectric infrared motion sensor, specially designed for Arduino. This sensor integrates an integrated digital pyroelectric infrared sensor, Connect the S pin of module to Digital 3 of UNO board, connect the negative pin to GND port, positive pin to 5V port.4 KB (556 words) - 14:15, 7 January 2021
- This basic application module is widely applied to Arduino, Raspberry Pi platforms.<br> You can simply connect to an IO port to have your first taste of Arduino.<br>3 KB (501 words) - 16:12, 7 January 2021
- This module should be used together with EASY plug control board. ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d3 KB (368 words) - 16:38, 7 January 2021
- ...to drive the DC motors, however, sometimes need to connect the motor drive board to UNO using lots of jumper wires, pretty inconvenient.<br> Just simply stack the shield onto UNO board to power the shield and UNO board. The 3 kinds of power supply are as follows:<br>5 KB (682 words) - 12:00, 6 January 2021
- ...7 in 1 sensor learning kit developed by Keyestudio. You will have a set of Arduino's most common and useful electronic sensors and modules. <br> The sample codes for this sensor kit are based on ARDUINO because it's open source and easy. And if you are good at this, you can als9 KB (1,534 words) - 15:37, 17 December 2020
- ...module is able to make some light-interactive works, fully compatible with Arduino microcontroller and raspberry pi system. ...https://wiki.keyestudio.com/Ks0001_keyestudio_UNO_R3_BOARD keyestudio UNO board]4 KB (488 words) - 11:17, 4 July 2022
- == Getting Started with Arduino == When we get control board, we need to download Arduino IDE and driver firstly.9 KB (1,379 words) - 08:21, 29 April 2021
- [[image:KS0240 (1).jpg|thumb|500px|right|Keyestudio EASY plug Control Board V2.0]] The processor used in keyestudio EASY plug control board V2.0 is ATmega328. <br>11 KB (1,729 words) - 16:37, 30 October 2018
- == Getting Started with Arduino == When we get control board, we need to download Arduino IDE and driver firstly.9 KB (1,406 words) - 17:18, 13 July 2021
- ...use this expansion board, which is directly stacked on the Arduino UNO R3 board. It can drive up to 16 servos and use I2C input, occupying A4 and A5 pins o ...tp://wiki.keyestudio.com/index.php/Ks0001_keyestudio_UNO_R3_BOARD UNO R3 board ]. <br>4 KB (618 words) - 11:16, 22 December 2023
- ...ionally, its 2.54mm anti-reverse interfaces are compatible with Micro:bit, Arduino and other control boards. <br> With this driver board, you can make a cool Mecanum 4WD smart car.<br>2 KB (322 words) - 13:46, 10 January 2022
- ...to drive the DC motors, however, sometimes need to connect the motor drive board to UNO using lots of jumper wires, pretty inconvenient.<br> ...yestudio motor shield with L298P as core. Just simply stack it onto UNO R3 board when using. Note that the motor’s speed and direction interfaces have bee4 KB (601 words) - 10:18, 29 April 2021
- [[image:KS0240 (1).jpg|thumb|500px|right|Keyestudio EASY plug Control Board V2.0]] The processor used in keyestudio EASY plug control board V2.0 is ATmega328. <br>11 KB (1,790 words) - 11:35, 29 April 2021
- ...ere are four round buttons, 2 small buttons, providing input expansion for Arduino joystick and buttons. Onboard slide switch can switch between 3.3V and 5V.< * Compatible with UNO R3 and MEGA 2560 control board.5 KB (654 words) - 10:31, 29 April 2021
- ...to drive the DC motors, however, sometimes need to connect the motor drive board to UNO using lots of jumper wires, pretty inconvenient.<br> ...yestudio motor shield with L298P as core. Just simply stack it onto UNO R3 board when using. Note that the motor’s speed and direction interfaces have bee4 KB (614 words) - 15:39, 14 September 2018
- ...ouch sensors mostly on electronic device. Instead of buttons, upgrade your Arduino project with our new version touch sensor and make it cool!<br> ...digital capacitive touch sensor provides a one-touch style switch on your Arduino project. It uses the most popular capacitive sensing technology which is th3 KB (554 words) - 16:13, 7 January 2021
- ==MKS BaseV1.2 3D Printer Controller Board (RAMPS 1.4 + Arduino 2560 remix board)== ...assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for7 KB (1,177 words) - 15:07, 7 January 2021
- [[image:ks0389.png|thumb|500px|right|Keyestudio ESP8266 WiFi board]] This keyestudio ESP8266 WI-FI development board is based on the ESP8266-12FWIFI module developed by Ai-Thinker. <br>10 KB (1,606 words) - 10:13, 6 January 2021