KS0221 keyestudio Ultimate Starter Kit for Raspberry Pi

keyestudio Ultimate Starter Kit for Raspberry Pi

Kit Introduction

Raspberry Pi is a delicate card computer. This is a starter kit of Raspberry Pi, very suitable for zero-based raspberry pi enthusiasts. Through this kit, you can learn more about the knowledge of linux operating system, as well as C, python and other language programming based on the debian system of Raspberry Pi. This kit also provides you with some related sensors and modules applied to the Raspberry Pi.
We offer richer learning materials that allow you to learn about Raspberry Pi from scratch. The learning materials include the installation and usage of the Raspberry Pi related system, where also offer you the learning courses of Raspberry Pi collocated with some commonly used sensors and modules. It would be better If you are an arduino hobbyist because arduino and Raspberry Pi are the best partners. You can make more creative DIY works via arduino strong community support and rich third-party library resources, integrating into Raspberry Pi's powerful function support to motivate your creativity and inspiration!

Kit List

No.	Product Name	Quantity	Picture
1	Keyestudio RPI GPIO-PCF8591 Shield	1
2	LED - Blue	5
3	LED - Red	5
4	LED - Yellow	5
5	LED - RGB	1
6	220Ω Resistor	8
7	10KΩ Resistor	5
8	1KΩ resistor	5
9	10KΩ Potentiometer	1
10	Buzzer (active)	1
11	Buzzer (passive)	1
12	Large Button Switch	4
13	Ball Tilt Sensor	2
14	Photo Resistor	3
15	Flame Sensor	1
16	LM35 Temp Sensor	1
17	IC 74HC595N 16-pin	1
18	1-digit LED	1
19	4-digit LED	1
20	8*8 LED Matrix	1
21	2x16 LCD display	1
22	IR Receiver	1
23	IR Remote Control	1
24	Servo Motor	1
25	Stepper Driver	1
26	Stepper Motor	1
27	Joystick Module	1
28	Relay Module	1
29	PIR Motion Sensor	1
30	Analog Gas Sensor	1
31	ADXL345 Three Axis Acceleration Module	1
32	HC-SR04 Ultrasonic Sensor	1
33	DS3231 Clock Module	1
34	DHT11 Temperature and Humidity Sensor	1
35	Soil Humidity sensor	1
36	RC522 RFID Module	1
37	RFID Card	1
38	Access Key	1
39	RPI GPIO Shield	1
40	Pin Headers	40
41	830-hole Breadboard	1
42	Female to Female Dupont Wire	20
43	Male to Female Dupont Wire	20
44	breadboard Jumper Wire	30
45	40 pin Colorful Jumper Wire	1

Kit Contents

Lesson 1: Hello World
Lesson 2: LED Blinking
Lesson 3: Breathing LED
Lesson 4: Traffic Light
Lesson 5: LED Chasing Effect
Lesson 6: Button-controlled LED
Lesson 7: Passive Buzzer
Lesson 8: Active Buzzer
Lesson 9: Responder
Lesson 10: Flame Sensor
Lesson 11: Ball Tilt Sensor
Lesson 12: IR Remote Control
Lesson 13: 1-digit LED Segment Display
Lesson 14: 74HC595
Lesson 15: 4-digit LED Segment Display
Lesson 16: LED Matrix Display
Lesson 17: 1602 LCD
Lesson 18: RGB LED
Lesson 19: 9g Servo Control
Lesson 20: ULN2003 Stepper Motor
Lesson 21: Photo Resistor
Lesson 22: LM35 Temp Sensor
Lesson 23: pcf8591
Lesson 24: PIR Motion Sensor
Lesson 25: MQ-2 Analog Gas Sensor
Lesson 26: ADXL345 Acceleration Module
Lesson 27: Ultrasonic Sensor
Lesson 28: Joystick Module
Lesson 29: 5V Relay
Lesson 30: DHT11 Temp and Humidity Sensor
Lesson 31: Soil Humidity Sensor
Lesson 32: DS3231 Clock Module

System Programming & Corresponding Tool Library Installation

1. Format the TFT card:
a. Plug the TFT card into the USB port through the card reader, open and install the SDFormatter tool in tool folders we provided. Open the tool as the figure shown below:

Tool Website: https://www.sdcard.org/downloads/formatter_4/index.html

b. The Driver in the upper figure: G is the TFT card just inserted. If you have several other TFT cards inserted in the computer, you can pass the drop-down menu to select the TFT card that needs to be formatted. And then click "Format",it will automatically format the TFT card. The formatting process will pop up the warning as shown below, then click OK.

c. The picture below shows the successful format of the TFT card:

2. Program Raspberry Mirror Image:
a. Open the Win32DiskImager in tool folder we provided, open the tool as the following figure shown:

b. Click marked 1 to select the formatted TFT card, then click marked 2 to choose the system image file "2017-01-11-raspbian-jessie-lite" in the raspberry image folder we provided. The figure shown as below:

 Raspberry Pi Download Address：https://www.raspberrypi.org/downloads/   

c. The above steps are configured well and click “Write”, it will automatically program the raspberry mirror image to the TFT card, and you need to wait for a few minutes in this process. Below shows the Write Successful. Then click “OK “ to unplug the TFT card.

Documents

File:
https://drive.google.com/open?id=1309GFYVPZwPOBOqR1904CCM0fNGei9kD

Download Link of Mirror Image File:
https://www.raspberrypi.org/downloads/raspbian/

Buy From

http://www.keyestudio.com/keyestudio-rpi-t-shape-gpio-shield.html