KS0498 Keyestudio MEGA 2560 R3 Development Board(Compatible Arduino): Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 215: Line 215:


Let’s install the driver of Keyestudio MEGA 2560 R3 Development Board.. The USB-TTL chip on 2560 R3 Development Board adopts CP2102 serial chip. The driver program of this chip is included in Arduino 1.8 version and above, which is convenient. Plug on USB port of board, the computer can recognize the hardware and automatically install the driver of CP2102.
Let’s install the driver of Keyestudio MEGA 2560 R3 Development Board.. The USB-TTL chip on 2560 R3 Development Board adopts CP2102 serial chip. The driver program of this chip is included in Arduino 1.8 version and above, which is convenient. Plug on USB port of board, the computer can recognize the hardware and automatically install the driver of CP2102.
<big>
<span style=color:red>Note: If the version of Arduino IDE you download is below 1.8, you need to download the driver of CP2102.</span>
Download the driver of CP2102:</span>
https://fs.keyestudio.com/CP2102-WIN</span></big>


If install unsuccessfully, or you intend to install manually, open the device manager of computer. Right click Computer----- Properties----- Device Manager.
If install unsuccessfully, or you intend to install manually, open the device manager of computer. Right click Computer----- Properties----- Device Manager.

Revision as of 09:11, 27 November 2020


0498.png




Description

Keyestudio Mega 2560 R3 is a microcontroller board based on the ATMEGA2560-16AU , fully compatible with ARDUINO MEGA 2560 R3. It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, 1 ICSP header, and a reset button. The built-in ICSP port can burn the firmware for ATMEGA2560-16AU directly. This chip is burnt the firmware well before leaving the factory, therefore, we hardly use it. We can power on by USB wire, DC head and Vin GND pins. To facilitate wiring, a 0.5 m USB wire is provided for you.


Specification

  • Microcontroller: ATMEGA2560-16AU
  • USB serial chip:CP2102
  • Operating Voltage: 5V
  • Input Voltage (recommended):DC 7-12V
  • Digital I/O Pins: 54 (D0-D53)
  • PWM Digital I/O Pins:15(D2-D13 D44-D46)
  • Analog Input Pins: 16(A0-A15)
  • DC Current per I/O Pin: 20 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 256 KB of which 8 KB used by bootloader
  • SRAM: 8 KB
  • EEPROM: 4 KB
  • Clock Speed: 16 MHz
  • LED_BUILTIN:D13

Element and Pin Interfaces:

Here is an explanation of what every element and interface of the board does:
KS0498标注图 画板 1.jpg

KS0001 5-1.png Digital I/O

Arduino MEGA has 54 digital input/output pins (of which 15 can be used as PWM outputs). These pins can be configured as digital input pin to read the logic value (0 or 1). Or used as digital output pin to drive different modules like LED, relay, etc.
Using pinMode(), digitalWrite(), and digitalRead() functions.

KS0001 5-2.png GND

Ground pins

KS0001 5-3.png AREF

Reference voltage (0-5V) for analog inputs. Used with analogReference(). Configures the reference voltage used for analog input (i.e. the value used as the top of the input range).

KS0001 5-4.png SDA

IIC communication pin

KS0001 5-5.png SCL

IIC communication pin

KS0001 5-6.png RESET Button

You can reset your Arduino board

KS0001 5-7.png USB Connection

Arduino board can be powered via USB connector.
All you needed to do is connecting the USB port to PC using a USB cable.

KS0001 5-8.png D13 LED

There is a built-in LED driven by digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.

KS0001 5-9.png CP2102

USB to serial chip, can convert the USB signal into serial port signal.

KS0001 5-10.png TX LED

Onboard you can find the label: TX (transmit)
When Arduino board communicates via serial port, send the message, TX led flashes.

KS0001 5-11.png RX LED

Onboard you can find the label: RX(receive )
When Arduino board communicates via serial port, receive the message, RX led flashes.

KS0001 5-12.png Crystal Oscillator

How does Arduino calculate time? by using a crystal oscillator.
The number printed on the top of the Arduino crystal is 16.000H9H. It tells us that the frequency is 16,000,000 Hertz or 16MHz.

KS0001 5-13.png Voltage Regulator

To control the voltage provided to the Arduino board, as well as to stabilize the DC voltage used by the processor and other components.
Convert an external input DC7-12V voltage into DC 5V, then switch DC 5V to the processor and other components.

KS0001 5-14.png DC Power Jack

Arduino board can be supplied with an external power DC7-12V from the DC power jack.

KS0001 5-15.png IOREF

This pin on the board provides the voltage reference with which the microcontroller operates. A properly configured shield can read the IOREF pin voltage and select the appropriate power source or enable voltage translators on the outputs for working with the 5V or 3.3V.

KS0001 5-17.png Power Pin 3V3

A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.

KS0001 5-16.png RESET Header

Connect an external button to reset the board. The function is the same as reset button.

KS0001 5-18.png Power Pin 5V

Provides 5V output voltage

KS0001 5-19.png Vin

You can supply an external power input DC7-12V through this pin to Arduino board.

KS0001 5-20.png Analog Pins

Onboard has 16 analog inputs, labeled A0 to A15.

KS0001 5-21.png ICSP (In-Circuit Serial Programming) Header

the AVR, an Arduino micro-program header consisting of MOSI, MISO, SCK, RESET, VCC, and GND.
It is often called the SPI (serial peripheral interface) and can be considered an "extension" of the output. In fact, slave the output devices to the SPI bus host.
When connecting to PC, program the firmware to ATMEGA2560-16AU.

KS0001 5-22.png Microcontroller

Each Arduino board has its own microcontroller. You can regard it as the brain of your board.
The main IC (integrated circuit) on the Arduino is slightly different from the panel pair. Microcontrollers are usually from ATMEL. Before you load a new program on the Arduino IDE, you must know what IC is on your board. This information can be checked at the top of IC.

KS0001 5-23.png Power LED Indicator

Powering the Arduino, LED on means that your circuit board is correctly powered on. If LED is off, connection is wrong.



Specialized Functions of Some Pins:

1. Serial Communication: D0 (RX0) and D1 (TX1); Serial 1: D19 (RX1) and D18 (TX1); Serial 2: D17 (RX2) and D16 (TX2); Serial 3: D15 (RX3) and D14 (TX3). Used to receive (RX) and transmit (TX) TTL serial data. Pins 0 and 1 are also connected to the corresponding pins of the CP2102 USB-to-TTL Serial chip.

2. PWM Pins (Pulse-Width Modulation): D2 to D13, and D44 to D46. Provide 8-bit PWM output with the analogWrite() function.

3. External Interrupts: D2 (interrupt 0), D3 (interrupt 1), D18 (interrupt 5), D19 (interrupt 4), D20 (interrupt 3), and D21 (interrupt 2). These pins can be configured to trigger an interrupt on a low level, a rising or falling edge, or a change in level. See the attachInterrupt() function for details.

4. SPI communication: D53 (SS), D52 (SCK), D51 (MOSI), D50 (MISO). These pins support SPI communication using theSPI library. The SPI pins are also broken out on the ICSP header, which is physically compatible with the Arduino Uno. 

5. IIC communication: D20 (SDA); D21 (SCL). Support TWI communication using the Wire library. 


Windows System

Installing Arduino IDE

When getting this control board, we need to install Arduino IDE Enter the website https://www.arduino.cc/, click thumb and thumb


thumb

Select the version you want to download, the latest version could be downloaded.


thumb

Alternatively, you could select previous release. In this project, we use 1.8.12 version.


thumb

Clickthumb to view the below page


thumb


Click thumb to download an installer of Arduino 1.8.12 version,which needs to be installed manually. When you tap thumb,a zip file of Arduino 1.8.12 version will be directly downloaded, and you only need to unzip it to finish installation.


thumb

Click thumbicon to download Arduino IDE.

Installing driver

Let’s install the driver of Keyestudio MEGA 2560 R3 Development Board.. The USB-TTL chip on 2560 R3 Development Board adopts CP2102 serial chip. The driver program of this chip is included in Arduino 1.8 version and above, which is convenient. Plug on USB port of board, the computer can recognize the hardware and automatically install the driver of CP2102. Note: If the version of Arduino IDE you download is below 1.8, you need to download the driver of CP2102.

Download the driver of CP2102: https://fs.keyestudio.com/CP2102-WIN


If install unsuccessfully, or you intend to install manually, open the device manager of computer. Right click Computer----- Properties----- Device Manager.


thumb

There is a yellow exclamation mark on the page, which implies installing the driver of CP2102 unsuccessfully. Then we double click the hardware and update the driver.


thumb

Click “OK” to enter the following page, click “browse my computer for updated driver software”, find out the installed or downloaded ARDUINO software. As shown below:


thumb

There is a DRIVERS folder in Arduino software installed package(thumb), open driver folder and you can see the driver of CP210X series chips.


We click “Browse”, then find out the driver folder, or you could enter “driver” to search in rectangular box, then click “next”, the driver will be installed successfully. (I place Arduino software folder on the desktop, you could follow my way)


thumb


Open device manager, we will find the yellow exclamation mark disappear. The driver of CP2102 is installed successfully.
thumb

thumb

Arduino IDE Setting

Clickthumb icon,open Arduino IDE.


thumb

To avoid the errors when uploading the program to the board, you need to select the correct Arduino board that matches the board connected to your computer. Then come back to the Arduino software, you should click Tools→Board, select the board. (as shown below)


thumb

Then select the correct COM port (you can see the corresponding COM port after the driver is successfully installed)


thumb

thumb

Before uploading the program to the board, let’s demonstrate the function of each symbol in the Arduino IDE toolbar.
0085=17.png

A- Used to verify whether there is any compiling mistakes or not. B- Used to upload the sketch to your Arduino board. C- Used to create shortcut window of a new sketch. D- Used to directly open an example sketch. E- Used to save the sketch. F- Used to send the serial data received from board to the serial monitor.

Start your first program

Open the file to select Example, choose BLINK from BASIC, as shown below:



048610png.png


048611png.png

Set board and COM port, the corresponding board and COM port are shown on the lower right of IDE.


048612png.png

Click 0486-20.png to start compiling the program, check errors.


048613png.png

Click 0486-23.pngto upload the program, upload successfully.


048614png.png

Upload the program successfully, the onboard LED lights on for 1s, lights off for 1s. Congratulation, you finish the first program.

MAC System

Install Arduino IDE on MAC System

The installation instruction is as same as the chapter 4.1, as shown below:


图片8883.png

Download the Driver of CP2102

https://fs.keyestudio.com/CP2102-MAC

How to Install the Driver of CP2102

https://wiki.keyestudio.com/How_to_Install_the_Driver_of_CP2102_on_MAC_System

Arduino IDE Setting

The setting method is as same as the chapter 5.3 except from COM port, as shown below.


0497=图片8.png

Resources

https://fs.keyestudio.com/KS0498