Ks0001 keyestudio UNO R3 BOARD: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 290: Line 290:
{| class="wikitable" cellpadding="1" cellspacing="1"
{| class="wikitable" cellpadding="1" cellspacing="1"
|-
|-
! align="center" scope="row" |<br>[[Image:IDE 1.png|600px|frameless]] Verify/Compile
!scope="row" |[[Image:IDE 1.png|600px|frameless]] Verify/Compile
|Check the code for errors
|Check the code for errors
|-
|-
! align="center" scope="row" |<br>[[Image:IDE 2.png|600px|frameless]] Upload
!scope="row" |[[Image:IDE 2.png|600px|frameless]] Upload
| Upload the current Sketch to the Arduino
| Upload the current Sketch to the Arduino
|-
|-
! scope="row" |<br>[[Image:IDE 3.png|600px|frameless]] New
!scope="row" |[[Image:IDE 3.png|600px|frameless]] New
| Create a new blank Sketch
| Create a new blank Sketch
|-
|-
! scope="row" |<br>[[Image:IDE 4.png|600px|frameless]] Open
! scope="row" |[[Image:IDE 4.png|600px|frameless]] Open
| Show a list of Sketches
| Show a list of Sketches
|-
|-
! scope="row" |<br>[[Image:IDE 5.png|600px|frameless]] Save
! scope="row" |[[Image:IDE 5.png|600px|frameless]] Save
| Save the current Sketch
| Save the current Sketch
|-
|-
! scope="row" |<br>[[Image:IDE 6.png|600px|frameless]] Serial Monitor
! scope="row" |[[Image:IDE 6.png|600px|frameless]] Serial Monitor
| Display the serial data being sent from the Arduino
| Display the serial data being sent from the Arduino
|-
|-

Revision as of 10:40, 26 July 2018

keyestudio UNO R3

Ks0001 UNO.png

Introduction

keyestudio Uno R3 is a microcontroller board based on the ATmega328 (datasheet), fully compatible with ARDUINO UNO REV3.
It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, 2 ICSP headers and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
Note that the two ICSP headers separately used to program the firmware to ATMEGA16U2-MU and ATMEGA328P-PU, but we have programmed the two chips, so generally no need to use them.
The Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 programmed as a USB-to-serial converter.
The UNO is the best board to get started with electronics and coding. If this is your first experience tinkering with the platform, the UNO is the most robust board you can start playing with.


Tech Specs

Microcontroller ATmega328P-PU
Operating Voltage 5V
Input Voltage (recommended) 7-12V
Digital I/O Pins 14 (of which 6 provide PWM output)
PWM Digital I/O Pins 6 (D3, D5, D6, D9, D10, D11)
Analog Input Pins 6 (A0-A5)
DC Current per I/O Pin 20 mA
DC Current for 3.3V Pin 50 mA
Flash Memory 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM 2 KB (ATmega328P-PU)
EEPROM 1 KB (ATmega328P-PU)
Clock Speed 16 MHz
LED_BUILTIN D13


Dimensions


UNO dimensions.png

Element and Pin Interfaces

Here is an explanation chart of what every element and interface of the board does:


Ks0001-pinout.png

KS0001 5-1.png ICSP (In-Circuit Serial Programming) Header

In most case, ICSP is the AVR,an Arduino micro-program header consisting of MOSI, MISO, SCK, RESET, VCC, and GND. It is often called the SPI (serial peripheral interface) and can be considered an "extension" of the output. In fact, slave the output devices under the SPI bus host.
When connecting to PC, program the firmware to ATMEGA328P-PU.

KS0001 5-2.png Power LED Indicator

Powering the Arduino, LED on means that your circuit board is correctly powered on. If LED is off, connection is wrong.

KS0001 5-3.png Digital I/O

Arduino UNO has 14 digital input/output pins (of which 6 can be used as PWM outputs). These pins can be configured as digital input pin to read the logic value (0 or 1). Or used as digital output pin to drive different modules like LED, relay, etc. The pin labeled “〜” can be used to generate PWM.

KS0001 5-4.png GND ( Ground pin headers)

Used for circuit ground

KS0001 5-5.png AREF

Reference voltage (0-5V) for analog inputs. Used with analogReference().

KS0001 5-6.png SDA

IIC communication pin

KS0001 5-7.png SCL

IIC communication pin

KS0001 5-8.png ICSP (In-Circuit Serial Programming) Header

In most case, ICSP is the AVR,an Arduino micro-program header consisting of MOSI, MISO, SCK, RESET, VCC, and GND. Connected to ATMEGA 16U2-MU. When connecting to PC, program the firmware to ATMEGA 16U2-MU.

KS0001 5-9.png RESET Button

You can reset your Arduino board, for example, start the program from the initial status. You can use the RESET button.

KS0001 5-10.png D13 LED

There is a built-in LED driven by digital pin 13. When the pin is HIGH value, the LED is on, when the pin is LOW, it's off.

KS0001 5-11.png USB Connection

Arduino board can be powered via USB connector. All you needed to do is connecting the USB port to PC using a USB cable.

KS0001 5-12.png ATMEGA 16U2-MU

USB to serial chip, can convert the USB signal into serial port signal.

KS0001 5-13.png TX LED

Onboard you can find the label: TX (transmit) When Arduino board communicates via serial port, send the message, TX led flashes.

KS0001 5-14.png RX LED

Onboard you can find the label: RX(receive ) When Arduino board communicates via serial port, receive the message, TX led flashes.

KS0001 5-15.png Crystal Oscillator

Helping Arduino deal with time problems. How does Arduino calculate time? by using a crystal oscillator.
The number printed on the top of the Arduino crystal is 16.000H9H. It tells us that the frequency is 16,000,000 Hertz or 16MHz.

KS0001 5-16.png Voltage Regulator

To control the voltage provided to the Arduino board, as well as to stabilize the DC voltage used by the processor and other components.
Convert an external input DC7-12V voltage into DC 5V, then switch DC 5V to the processor and other components.

KS0001 5-17.png DC Power Jack

Arduino board can be supplied with an external power DC7-12V from the DC power jack.

KS0001 5-18.png IOREF

Used to configure the operating voltage of microcontrollers. Use it less.

KS0001 5-19.png RESET Header

Connect an external button to reset the board. The function is the same as reset button (labeled 9)

KS0001 5-20.png Power Pin 3V3

A 3.3 volt supply generated by the on-board regulator. Maximum current draw is 50 mA.

KS0001 5-21.png Power Pin 5V

Provides 5V output voltage

KS0001 5-22.png Vin

You can supply an external power input DC7-12V through this pin to Arduino board.

KS0001 5-23.png Analog Pins

Arduino UNO board has 6 analog inputs, labeled A0 through A5.
These pins can read the signal from analog sensors (such as humidity sensor or temperature sensor), and convert it into the digital value that can read by microcontrollers) Can also used as digital pins, A0=D14, A1=D15, A2=D16, A3=D17, A4=D18, A5=D19.

KS0001 5-24.png Microcontroller

Each Arduino board has its own microcontroller. You can regard it as the brain of your board.
The main IC (integrated circuit) on the Arduino is slightly different from the panel pair. Microcontrollers are usually from ATMEL. Before you load a new program on the Arduino IDE, you must know what IC is on your board. This information can be checked at the top of IC.

Specialized Functions of Some Pins

  • Serial communication: Digital pins 0 (RX) and 1 (TX).
  • PWM Interfaces (Pulse-Width Modulation): D3, D5, D6, D9, D10, D11
  • External Interrupts: D2 (interrupt 0) and D3 (interrupt 1). These pins can be configured to trigger an interrupt on a low value, a rising or falling edge, or a change in value.
  • SPI communication: D10 (SS), D11 (MOSI), D12 (MISO), D13 (SCK). These pins support SPI communication using the SPI library.
  • IIC communication: A4 (SDA); A5(SCL)

Warnings:

  • The Arduino Uno has a resettable polyfuse that protects your computer's USB ports from shorts and overcurrent. If more than 500 mA is applied to the USB port, the fuse will automatically break the connection until the short or overload is removed.
  • Automatic (Software) Reset:

Rather than requiring a physical press of the reset button before an upload, the Arduino Uno board is designed in a way that allows it to be reset by software running on a connected computer.

  • The Uno board contains a trace that can be cut to disable the auto-reset. The pads on either side of the trace can be soldered together to re-enable it. It's labeled "RESET-EN". You may also be able to disable the auto-reset by connecting a 110 ohm resistor from 5V to the reset line; see this forum thread for details.

Detailed Use with ARDUINO Software as follows:

Step1 | Download the Arduino environment (IDE)

When you get the UNO development board, first you should install the Arduino software and driver.
We usually use the Windows software Arduino 1.5.6 version. You can download it from the link below:
https://www.arduino.cc/en/Main/OldSoftwareReleases#1.5.x
Or you can browse the ARDUINO website to download the latest version from this link, https://www.arduino.cc, pop up the following interface.
KS0313-1.png

Then click the SOFTWARE on the browse bar, you will have two options ONLINE TOOLS and DOWNLOADS.
KS0313-2.png

Click DOWNLOADS, it will appear the latest software version of ARDUINO 1.8.5 shown as below.
KS0313-3.png

In this software page, on the right side you can see the version of development software for different operating systems. ARDUINO has a powerful compatibility. You should download the software that is compatible with the operating system of your computer.
We will take WINDOWS system as an example here. There are also two options under Windows system, one is installed version, the other is non-installed version. For simple installed version, first click Windows Installer, you will get the following page.

KS0313-4.png

KS0313-5.png

This way you just need to click JUST DOWNLOAD, then click the downloaded file to install it.
For non-installed version, first click Windows ZIP file, you will also get the pop-up interface as the above figure.
Click JUST DOWNLOAD, and when the ZIP file is downloaded well to your computer, you can directly unzip the file and click the icon of ARDUINO software to start it.


Installing Arduino (Windows)

Install Arduino with the exe. Installation package downloaded well.
713.png

Click“I Agree”to see the following interface.
714.png

Click “Next”. Pop up the interface below.
715.png

You can press Browse… to choose an installation path or directly type in the directory you want.
Then click “Install” to initiate installation.
718.jpg

Wait for the installing process, if appear the interface of Window Security, just continue to click Install to finish the installation.
716.png

Installing Driver:

Next, we will introduce the driver installation of UNO R3 development board. The driver installation may have slight differences in different computer systems. So in the following let’s move on to the driver installation in the WIN 7 system.
The Arduino folder contains both the Arduino program itself and the drivers that allow the Arduino to be connected to your computer by a USB cable. Before we launch the Arduino software, you are going to install the USB drivers.

KS0001-1.jpg
Plug one end of your USB cable into the Arduino and the other into a USB socket on your computer. When you connect UNO board to your computer at the first time, right click the icon of your “Computer” —>for “Properties”—> click the “Device manager”, under “Other Devices”, you should see an icon for “Unknown device” with a little yellow warning triangle next to it. This is your Arduino.

Driver 1.png
Then right-click on the device and select the top menu option (Update Driver Software...) shown as the figure below..
Driver 2.png

It will then be prompted to either “Search Automatically for updated driversoftware” or “Browse my computer for driver software”. Shown as below. In this page, select “Browse my computer for driver software”.
Driver 3.png

After that, select the option to browseand navigate to the “drivers” folder of Arduino installation.
Driver 4.png

Click “Next” and you may get a security warning, if so, allow the software to be installed. Shown as below.
Driver 5.png

Once the software has been installed, you will get a confirmation message. Installation completed, click “Close”.
Driver 6.png

Up to now, the driver is installed well. Then you can right click “Computer” —>“Properties”—>“Device manager”, you should see the device as the figure shown below.
Driver 7.png

Introduction for Arduino IDE Toolbar:

Double-click the icon of Arduino software downloaded well, you will get the interface shown below.
Ks0313图片1.png
(Note: if the Arduino software loads in the wrong language, you can change it in the preferences dialog. See the environment page for details.)
717.png
The functions of each button on the Toolbar are listed below:
IDE.png

IDE 1.png Verify/Compile Check the code for errors
IDE 2.png Upload Upload the current Sketch to the Arduino
IDE 3.png New Create a new blank Sketch
IDE 4.png Open Show a list of Sketches
IDE 5.png Save Save the current Sketch
IDE 6.png Serial Monitor Display the serial data being sent from the Arduino

Features

  • 1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V.
  • The second one is a not connected pin, that is reserved for future purposes.
  • Stronger RESET circuit.
  • Atmega 16U2 replace the 8U2.




Pin definition and Rating

Usage

Download the Arduino environment

Get the latest version from the download page.
When the download finishes, unzip the downloaded file. Make sure to preserve the folder structure. Double-click the folder to open it. There should be a few files and sub-folders inside.

Connect the board

The Arduino Uno, Mega, Duemilanove and Arduino Nano automatically draw power from either the USB connection to the computer or an external power supply. If you're using an Arduino Diecimila, you'll need to make sure that the board is configured to draw power from the USB connection. The power source is selected with a jumper, a small piece of plastic that fits onto two of the three pins between the USB and power jacks. Check that it's on the two pins closest to the USB port.
Connect the Arduino board to your computer using the USB cable. The green power LED (labelled PWR) should go on.

Install the drivers

Installing drivers for the Arduino Uno or Arduino Mega 2560 with Windows 7, Vista, or XP:
Plug in your board and wait for Windows to begin it's driver installation process. After a few moments, the process will fail, despite its best efforts
Click on the Start Menu, and open up the Control Panel.
While in the Control Panel, navigate to System and Security. Next, click on System. Once the System window is up, open the Device Manager.
Look under Ports (COM & LPT). You should see an open port named "Arduino UNO (COMxx)". If there is no COM & LPT section, look under "Other Devices" for "Unknown Device".
Right click on the "Arduino UNO (COmxx)" port and choose the "Update Driver Software" option.
Next, choose the "Browse my computer for Driver software" option.
Finally, navigate to and select the driver file named "arduino.inf", located in the "Drivers" folder of the Arduino Software download (not the "FTDI USB Drivers" sub-directory). If you are using an old version of the IDE (1.0.3 or older), choose the Uno driver file named "Arduino UNO.inf"
Windows will finish up the driver installation from there.
See also: step-by-step screenshots for installing the Uno under Windows XP.
Installing drivers for the Arduino Duemilanove, Nano, or Diecimila with Windows7, Vista, or XP:
When you connect the board, Windows should initiate the driver installation process (if you haven't used the computer with an Arduino board before).
On Windows Vista, the driver should be automatically downloaded and installed. (Really, it works!)
On Windows XP, the Add New Hardware wizard will open:
When asked Can Windows connect to Windows Update to search for software? select No, not this time. Click next.
Select Install from a list or specified location (Advanced) and click next.
Make sure that Search for the best driver in these locations is checked; uncheck Search removable media; check Include this location in the search and browse to the drivers/FTDI USB Drivers directory of the Arduino distribution. (The latest version of the drivers can be found on the FTDI website.) Click next.
The wizard will search for the driver and then tell you that a "USB Serial Converter" was found. Click finish.
The new hardware wizard will appear again. Go through the same steps and select the same options and location to search. This time, a "USB Serial Port" will be found.
You can check that the drivers have been installed by opening the Windows Device Mananger (in the Hardware tab of System control panel). Look for a "USB Serial Port" in the Ports section; that's the Arduino board.

Launch the Arduino application

Double-click the Arduino application. (Note: if the Arduino software loads in the wrong language, you can change it in the preferences dialog. See the environment page for details.)

Upload the program

Now, simply click the "Upload" button in the environment. Wait a few seconds - you should see the RX and TX leds on the board flashing. If the upload is successful, the message "Done uploading." will appear in the status bar. (Note: If you have an Arduino Mini, NG, or other board, you'll need to physically present the reset button on the board immediately before pressing the upload button.)
UR3 4.png

A few seconds after the upload finishes, you should see the pin 13 (L) LED on the board start to blink (in orange). If it does, congratulations! You've gotten Arduino up-and-running.
If you have problems, please see the troubleshooting suggestions.
You might also want to look at:
the examples for using various sensors and actuators
the reference for the Arduino language
The text of the Arduino getting started guide is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the guide are released into the public domain.


Extensions

Resources

Video:
http://www.keyestudio.com/wp/ks0001/

Datasheet:
https://drive.google.com/open?id=1y8RXlk26EeU0FfdZ825LTaBoqxtsez-i

Get One Now

Official Website
http://www.keyestudio.com/ks0001.html

Get on Amazon
https://www.amazon.ca/keyestudio-ATmega328P-Development-Compatible-Arduino/dp/B0168B39N4/

From Ebay: [1]