Ks0036 keyestudio Flame Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
<br>
==Introduction==
==Introduction==
This flame sensor can be used to detect fire or other lights whose wavelength stands at 760 nm ~ 1100 nm. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.
This flame sensor can be used to detect fire or other lights with wavelength stands at 760nm ~ 1100nm. <br>
<br>[[File:361.png|500px|frameless|thumb]]<br>
In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.
 
<br>[[File:Ks0036.png|500px|frameless|thumb]]<br>


<br>
==Specification==
==Specification==
*Supply Voltage: 3.3V to 5V
*Supply Voltage: 3.3V to 5V
*Detection Range: 20cm (4.8V) ~ 100cm (1V)
*Detection Range: 20cm (4.8V) ~ 100cm (1V)
*Rang of Spectral Bandwidth: 760nm to 1100nm
*Rang of Spectral Bandwidth: 760nm to 1100nm
*Operating Temperature: -25℃to 85℃
*Operating Temperature: -25℃ to 85℃
*Interface: Digital
*Interface: Digital
*Size: 44*16.7mm
*Weight: 4g


<br>
==Connection Diagram ==
==Connection Diagram ==
Connect the D0 pin to digital 2, GND pin to GND port, VCC pin to 5V port.
<br>[[File:Ks0036-1.png|700px|frameless|thumb]]<br>


<br>[[File:362.png|500px|frameless|thumb]]<br>
<br>
 
==Sample Code ==
==Sample Code ==


<pre>
<pre>
Line 41: Line 43:
     // turn LED off:
     // turn LED off:
     digitalWrite(ledPin, LOW);  
     digitalWrite(ledPin, LOW);  
}</pre>
}
</pre>


<br>
== Result ==
<br>[[File:KS0349 16-2.png|800px|frameless|thumb]]<br>
Done wiring and powered up, upload well the code to the board.<br>
Then if you put a lighter close to the sensor, when the sensor detects the flame, another led on the sensor is turned on.<br>
<br>[[File:KS0349 16-3.png|800px|frameless|thumb]]<br>
<br>
==Resources ==
==Resources ==


'''Video'''
* '''Video'''<br>
 
http://video.keyestudio.com/ks0036/
http://www.keyestudio.com/wp/2016/05/ks0036-keyestudio-flame-sensor-module/


'''PDF'''
* '''PDF and Code'''<br>
https://fs.keyestudio.com/KS0036


https://drive.google.com/open?id=1dTDZpdRHR3vbMpxszdVfiP4jjeo2Ke0m
<br>


==Buy from ==
==Buy from ==
'''Official Website'''


http://www.keyestudio.com/keyestudio-flame-sensor-for-arduino.html
*[https://www.keyestudio.com/free-shipping-keyestudio-flame-fire-detection-sensor-module-for-arduino-p0148.html   '''Official Website''']


'''Amazon Store'''
*[https://www.aliexpress.com/store/product/Free-shipping-Flame-sensor-for-arduino/1452162_2051417128.html?spm=2114.12010612.8148356.45.29bd7498iQQUVn  '''Shop on aliexpress''']


https://www.amazon.com/Keyestudio-Flame-Sensor-Arduino-raspberry/dp/B0172UM4RC/ref=sr_1_1?ie=UTF8&qid=1479956399&sr=8-1&keywords=keyestudio+Flame+Sensor+for+Arduino


[[Category: Sensor]]
[[Category: Sensor]]

Latest revision as of 14:55, 7 January 2021


Introduction

This flame sensor can be used to detect fire or other lights with wavelength stands at 760nm ~ 1100nm.
In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.
thumb


Specification

  • Supply Voltage: 3.3V to 5V
  • Detection Range: 20cm (4.8V) ~ 100cm (1V)
  • Rang of Spectral Bandwidth: 760nm to 1100nm
  • Operating Temperature: -25℃ to 85℃
  • Interface: Digital


Connection Diagram

Connect the D0 pin to digital 2, GND pin to GND port, VCC pin to 5V port.
thumb


Sample Code

const int flamePin = 2;     // the number of the flame pin
const int ledPin =  13;      // the number of the LED pin
// variables will change:
int State = 0;         // variable for reading status
void setup() {
  // initialize the LED pin as an output:
  pinMode(ledPin, OUTPUT);      
  // initialize the pushbutton pin as an input:
  pinMode(flamePin, INPUT);     
}
void loop(){
  // read the state of the value:
State = digitalRead(flamePin);
  if (State == HIGH) {     
    // turn LED on:    
    digitalWrite(ledPin, HIGH);  
  } 
  else {
    // turn LED off:
    digitalWrite(ledPin, LOW); 
}


Result


thumb
Done wiring and powered up, upload well the code to the board.
Then if you put a lighter close to the sensor, when the sensor detects the flame, another led on the sensor is turned on.

thumb


Resources

  • Video

http://video.keyestudio.com/ks0036/

  • PDF and Code

https://fs.keyestudio.com/KS0036


Buy from