Ks0061 keyestudio 1602 I2C Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(2 intermediate revisions by the same user not shown)
Line 71: Line 71:
==Resources ==
==Resources ==


* '''Get the Libraries of Wire and LiquidCrystal_I2C''' <br>
* '''Get the Libraries of Wire and LiquidCrystal_I2C and Code''' <br>
https://drive.google.com/open?id=1JUS0I9U2N30nYCxN323SlGm9Ywm_GRp2
https://fs.keyestudio.com/KS0061


* '''Video'''<br>
* '''Video'''<br>
http://video.keyestudio.com/ks0061/
http://video.keyestudio.com/ks0061/
* '''PDF'''<br>
https://drive.google.com/open?id=1Gfm8thFdAjMD9YhceG9Q2_TckFYOhZhP
* '''Code'''<br>
https://drive.google.com/open?id=1tHRzCyL5Ze6JcO6d7Z_p2H98ayy7idKX





Latest revision as of 09:10, 8 January 2021

Keyestudio 1602 I2C Module


thumb thumb


Introduction

keyestudio 1602 I2C module is a 16 character by 2 line LCD display with Blue background and White backlight.
The original 1602 LCD needs 7 IO ports to be up and running, but ours is built with Arduino IIC/I2C interface, saving you 5 IO ports.
This LCD is ready-to-use because it is compatible with the Arduino Liquid Crystal Library.
LCDs are great for printing data and showing values. Adding an LCD to your project will make it super portable and allow you to integrate up to 32 characters (16x2) of information.
On the back of LCD display there is a blue potentiometer. You can turn the potentiometer to adjust the contrast.
Notice that the screen will get brighter or darker and that the characters become more visible or less visible.


Specification

  • I2C Address:0x27
  • Backlight (Blue with white char color)
  • Supply voltage: 5V
  • Adjustable contrast


PINOUTS

  • GND: A pin that connects to ground
  • VCC: A pin that connects to a +5V power supply
  • SDA: A pin that connects to analog port A4 for IIC communication
  • SCL: A pin that connects to analog port A5 for IIC communication


Connection Diagram

I602 is equipped with 4 pins in total. SCL should be connected to analog 5, SDA to analog 4, VCC to +5V and GND to ground.
Below is connection diagram for your reference:

thumb


Sample Code

//Compatible with the Arduino IDE 1.0
//Library version:1.1
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,16,2); // set the LCD address to 0x27 for a 16 chars and 2 line display
void setup()
{
lcd.init(); // initialize the lcd
lcd.init();
// Print a message to the LCD.
lcd.backlight();
lcd.setCursor(3,0);
lcd.print("Hello, world!");
lcd.setCursor(2,1);
lcd.print("keyestudio!");
}
void loop()
{
}


What You Will See

Hookup well and upload the code to board, you should see the words “ Hello, World!” and “keyestudio” pop up on your LCD.

thumb

Remember you can adjust the contrast by turning the potentiometer on the back if you can’t make out the words clearly.

thumb

If you have any issues, make sure your code is correct and double-check your connection.


Resources

  • Get the Libraries of Wire and LiquidCrystal_I2C and Code

https://fs.keyestudio.com/KS0061

  • Video

http://video.keyestudio.com/ks0061/



Buy from