Ks0093 Keyestudio 3D Printer Kit MKS base V1.2 + 5x 8825 + LCD 12864 smart Controller: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(One intermediate revision by the same user not shown)
Line 2: Line 2:
<br>[[File:93-1.png|500px|frameless|thumb]]<br>
<br>[[File:93-1.png|500px|frameless|thumb]]<br>


<br>
==Description==
==Description==
1.The new MKS Base 1.2 3D Printer Controller board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for your Reprap 3D Printer.<br>
1.The new MKS Base 1.2 3D Printer Controller board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for your Reprap 3D Printer.<br>
Line 8: Line 9:
3. The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).<br>
3. The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).<br>


 
<br>
==Package list:==
==Package list:==
* 1pc MKS base V1.2 <br>
* 1pc Lcd12864 smart Controller <br>
* 5pcs 8825 stepper driver <br>
* 1pcs USB 2.0 cable <br>


1pc MKS base V1.2<br>
<br>
1pc Lcd12864 smart Controller<br>
== Adjusting the drive current ==
5pcs 8825 stepper driver<br>
In the kit, we have applied the A4988 drive module to drive stepper motor. When using, you can turn the potentiometer on the drive module to adjust the drive current. <br>
1pcs USB 2.0 cable<br>
The specific method please refer to the website link below: <br>
 
https://wiki.keyestudio.com/Ks0281_Keyestudio_Reprap_Stepper_Motor_Driver


<br>
==Connection Method==
==Connection Method==
A. Mount DRV8825 correctly, don’t mount reversely, or they will be burnt, as shown below:
A. Mount DRV8825 correctly, don’t mount reversely, or they will be burnt, as shown below:
Line 27: Line 33:
<br>[[File:ks0089-3.png|500px|frameless|thumb]]<br>
<br>[[File:ks0089-3.png|500px|frameless|thumb]]<br>


<br>
==Using Method==
==Using Method==
===Install Diver Software===
===Install Diver Software===
Line 45: Line 52:
<br>[[File:ks0089 5-7.png|500px|frameless|thumb]]<br>
<br>[[File:ks0089 5-7.png|500px|frameless|thumb]]<br>


<br>
===Install development environment software IDE===
===Install development environment software IDE===
Double click arduino-1.5.6-r2-windows to start.
Double click arduino-1.5.6-r2-windows to start.
Line 56: Line 64:
<br>[[File:ks0089 5-11.png|500px|frameless|thumb]]<br>
<br>[[File:ks0089 5-11.png|500px|frameless|thumb]]<br>


<br>
===Install Firmware for Main Board===
===Install Firmware for Main Board===
'''A.''' You must close Arduino IDE firstly, and then place three libraries LiquidCrystal, SPI and U8glib from Marlin_Marlin_v1→ArduinoAddons→Arduino_1.x.x→libraries into Arduino/libraries.
'''A.''' You must close Arduino IDE firstly, and then place three libraries LiquidCrystal, SPI and U8glib from Marlin_Marlin_v1→ArduinoAddons→Arduino_1.x.x→libraries into Arduino/libraries.
Line 70: Line 79:
<br>[[File:90-5.png|500px|frameless|thumb]]<br>
<br>[[File:90-5.png|500px|frameless|thumb]]<br>


<br>
===Install Slicer Software Repetier-Host===
===Install Slicer Software Repetier-Host===
First, run this application <br>[[File:ks0089 5-18.png|500px|frameless|thumb]]<br>
First, run this application <br>[[File:ks0089 5-18.png|500px|frameless|thumb]]<br>
Line 94: Line 104:
<br>[[File:ks0089 5-28.png|500px|frameless|thumb]]<br>
<br>[[File:ks0089 5-28.png|500px|frameless|thumb]]<br>


<br>
==Application of Slicer Software==
==Application of Slicer Software==
A. Run Repiter-Host,click Load to open a printing model.
A. Run Repiter-Host,click Load to open a printing model.
Line 120: Line 131:




 
<br>
==Resources ==
==Resources ==


'''Datasheet:'''<br>
https://fs.keyestudio.com/KS0093
https://drive.google.com/open?id=1kfToi5FjsUi3In98Dpdy-NDeq86eQ7W9
 
'''Download the PDF:'''<br>
https://drive.google.com/open?id=14h8oza-wKZKQJ3w5-SuFTD1aKCxh6QRQ


<br>


==Buy from ==
==Buy from ==
'''Official Website:''' http://www.keyestudio.com/ks0093.html
'''Official Website:''' <br>
https://www.keyestudio.com/keyestudio-3-d-printer-kit-mks-gen-v12-5x-8825-motor-lcd-12864-smart-controller-p0295-p0295.html






  [[Category: 3D Printer ]]
  [[Category: 3D Printer ]]

Latest revision as of 15:14, 7 January 2021

Keyestudio 3D Printer Kit MKS base V1.2 + 5x 8825 + LCD 12864 smart Controller


thumb


Description

1.The new MKS Base 1.2 3D Printer Controller board combines and improves the assets of the RAMPS 1.4 and Arduino Mega 2560 boards on a fantastic single board solution. The MKS Base 1.2 is an optimal 3D printer controller solution for your Reprap 3D Printer.
2. LCD 12864 Smart Controller
It contains a SD-Card reader. You can easy connect it to your Ramps board using the ""smart adapter"" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card.
3. The DRV8825 stepper motor driver carrier is a breakout board for TI’s DRV8825 microstepping bipolar stepper motor driver. The module has a pinout and interface that are nearly identical to those of our A4988 stepper motor driver board, so it can be used as a higher-performance drop-in replacement for those boards in many applications. The DRV8825 features adjustable current limiting, overcurrent and overtemperature protection, and six microstep resolutions (down to 1/32-step). It operates from 8.2 – 45 V and can deliver up to approximately 1.5 A per phase without a heat sink or forced air flow (rated for up to 2.2 A per coil with sufficient additional cooling).


Package list:

  • 1pc MKS base V1.2
  • 1pc Lcd12864 smart Controller
  • 5pcs 8825 stepper driver
  • 1pcs USB 2.0 cable


Adjusting the drive current

In the kit, we have applied the A4988 drive module to drive stepper motor. When using, you can turn the potentiometer on the drive module to adjust the drive current.
The specific method please refer to the website link below:
https://wiki.keyestudio.com/Ks0281_Keyestudio_Reprap_Stepper_Motor_Driver


Connection Method

A. Mount DRV8825 correctly, don’t mount reversely, or they will be burnt, as shown below:
thumb

B. As for 2004LCD, connect ESP1 to ESP1, ESP2 to ESP2, as shown below:
thumb

C. Diagram connection as shown below:
thumb


Using Method

Install Diver Software

A. Connect the main board with computer, and then right click “Computer” to enter “Device Manage”.
thumb
B. Double click “Other devices”, appearing “USB Serial Port”.
thumb
Then, right click “USB Serial Port” and select “Update Driver Software” to install driver software.
thumb
After that, select “Browse my computer for driver software” to find the file.
thumb
Browse to search for driver software.
thumb
After your driver software updated, click “Close” to finish.
thumb

C. Finally, installation is done, and double click “Ports”in “Device Manager”, you can see “USB Serial Port”.
thumb


Install development environment software IDE

Double click arduino-1.5.6-r2-windows to start. Select “I Agree”to accept license agreement.
thumb
Select components to install and click “Next”.
thumb
Click “Browse” and select another folder. Click “Install” to start the installation.
thumb
Finally, wait for a few minutes to finish.
thumb


Install Firmware for Main Board

A. You must close Arduino IDE firstly, and then place three libraries LiquidCrystal, SPI and U8glib from Marlin_Marlin_v1→ArduinoAddons→Arduino_1.x.x→libraries into Arduino/libraries.
thumb
B. Enter Marlin_Marlin_RAMPS_12864_Ver1this folder, double click Marlin_Marlin_RAMPS_12864_Ver1.ino this file, finally click “Tools” to set “Board”and “Port”.
thumb

thumb
After verifying, write code.
thumb
Done uploading.
thumb

C. After upload the firmware the LCD will display some parameter as shown below:
thumb


Install Slicer Software Repetier-Host

First, run this application
thumb

thumb

Click “Next” to continue.
thumb

Check “I accept the agreement”, and click “Next” to continue.
thumb
Select destination location, and click “Next” to continue.
thumb
Check components that should be installed, and click “Next” to continue.
thumb

Select star menu folder, and click “Next” to continue.
thumb
Click “Next” to continue.
thumb
Click “Install” to install.
thumb

thumb
Click “Finish” to exit Setup.
thumb


Application of Slicer Software

A. Run Repiter-Host,click Load to open a printing model.
thumb

B. Click Printer Settings to complete some setup, referring to below figure.
thumb

C. Enter Object Placement to set placing position, printing size and so on.
thumb

D. Click Slicer to set slicer, like printing speed. After setting slicer, click Start Slicing to begin slicing.
thumb

E. After slicing, go to Preview→G-Code Editor, copy G-Code to SD card, and then insert the card into the main board. It is time to kick off the print! Though the LCD screen go to : Print from SD→Desired File. Or you can connect your 3D printer to computer using a USB cable to start the print.
thumb

F. Click “Connect”and then click “Start Print” to begin the print. After some time, your printer gets ready and the buzzer rings, then you should press the button on LCD to start.
thumb

G. We just introduce a simple method about printing. Thanks to selling only main board by us, you should design your own structure and outlook of your 3D printer, and you should also set your own configuration to meet your need. After you assembling your printer, the printer need to be leveled, so you can make some setup in Preview and Manual Control, and surf the internet for further information.
thumb

H. We have a G-Code to test the main board. Power it on, open limit switch and stepper motor, drive three motors; put a Fnbduino.gco file to Preview, click Start Print, if the motors rotate, X/Y/Z value in Manual Control changes, the main board works as shown below:
thumb



Resources

https://fs.keyestudio.com/KS0093


Buy from

Official Website:
https://www.keyestudio.com/keyestudio-3-d-printer-kit-mks-gen-v12-5x-8825-motor-lcd-12864-smart-controller-p0295-p0295.html