Ks0106 keyestudio EASY plug Photocell Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
Line 10: Line 10:


<br>
<br>
==Specification==
==Specification==
*Interface: Easy plug
*Interface: Easy plug
Line 29: Line 28:


==Upload the Code==
==Upload the Code==
Copy and paste below code to [http://wiki.keyestudio.com/index.php/How_to_Download_Arduino_IDE Arduino IDE] and upload.  
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<pre>
<br>[[File:ks0398 4.1.png|600px|frameless|thumb]]<br>
int sensorPin =A2 ;
int value = 0;
void setup()
{
Serial.begin(9600); }
void loop()
{
value = analogRead(sensorPin);
Serial.println(value, DEC);
delay(50);
}
</pre>


<br>
<br>
==What You Should See==
==What You Should See==
<br>[[File:ks0398 4-1.png|500px|frameless|thumb]]<br>
Done uploading the code, you should see the analog value change in accordance with how much light your photoresistor is sensing.  
Done uploading the code, you should see the analog value change in accordance with how much light your photoresistor is sensing.  
<br>[[File:Ks0106-2-.png|700px|frameless|thumb]]<br>
<br>[[File:Ks0106-2-.png|600px|frameless|thumb]]<br>
 
<br>
==Controlling light brightness==
'''Hookup Guide'''<br>
Connect the EASY Plug photocell sensor and LED module to control board using RJ11 cable.
<br>[[File:光敏灯.jpg|600px|frameless|thumb]]<br>
 
<br>
'''Test Code'''<br>
Below is an example code for three LED modules experiment.
<br>[[File:ks0398 4.2.png|600px|frameless|thumb]]<br>


<br>
<br>
'''What You Should See'''<br>
The three LEDs are gradually brighter then gradually off one by one, circularly. <br>
If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board.
<br>[[File:ks0398 4-3.png|600px|frameless|thumb]]<br>


<br>
==Resources ==
==Resources ==
'''Download the PDF:'''<br>
'''Download the Arduino PDF:'''<br>
https://drive.google.com/open?id=1z1edMsDIlH3D6hI6BLVWNlrRQYFklpZK
https://drive.google.com/open?id=1z1edMsDIlH3D6hI6BLVWNlrRQYFklpZK
'''Download the Mixly Code and PDF:'''<br>
https://drive.google.com/open?id=1QFMQkdE19fnMpBHL657ze0H3Haj9H29j


<br>
<br>
==Buy from ==
==Buy from ==
*'''Official Website:''' http://www.keyestudio.com/ks0106.html
*[https://www.keyestudio.com/keyestudio-easy-plug-photoresistor-sensor-module-for-arduino-steam-p0072-p0072.html   '''Official Website''' ]


*[https://www.aliexpress.com/store/product/2016-New-Keyestudio-EASY-plug-Photoresistor-Sensor-Module-for-Arduino/1452162_32637445281.html?spm=2114.12010612.8148356.64.70f5484ethSftt  Shop on aliexpress ]
*[https://www.aliexpress.com/store/product/2016-New-Keyestudio-EASY-plug-Photoresistor-Sensor-Module-for-Arduino/1452162_32637445281.html?spm=2114.12010612.8148356.64.70f5484ethSftt  Shop on aliexpress ]


[[category:EASY Plug]]
[[category:EASY Plug]]

Revision as of 13:26, 6 May 2019

EASY plug Photocell Sensor

Introduction

A photoresistor or light-dependent resistor (LDR) or photocell is a light-controlled variable resistor. The principal is very simple. The resistance of photoresistor varies with incident light intensity. If the incident light intensity is high, the resistance decreases; if the light intensity is low, the resistance increases.
keyestudio EASY Plug photocell sensor is a semiconductor, integrated with a photoresistor, easy to use and very convenient for wiring.
It has features of high sensitivity, quick response, spectral characteristic and R-value consistence.
It can be applied in light-sensitive detector circuits, intelligent switch design and light- and dark-activated switching circuits.
Note: this module should be used together with EASY plug control board.


Specification

  • Interface: Easy plug
  • Sensor type: analog
  • Working voltage: 5V
  • Quick response


Technical Details

  • Dimensions: 38mm*20mm*18mm
  • Weight: 4.3g


Connect It Up

Connect the EASY Plug photocell sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb

Upload the Code

Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See


thumb

Done uploading the code, you should see the analog value change in accordance with how much light your photoresistor is sensing.
thumb


Controlling light brightness

Hookup Guide
Connect the EASY Plug photocell sensor and LED module to control board using RJ11 cable.
thumb


Test Code
Below is an example code for three LED modules experiment.
thumb


What You Should See
The three LEDs are gradually brighter then gradually off one by one, circularly.
If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board.
thumb



Resources

Download the Arduino PDF:
https://drive.google.com/open?id=1z1edMsDIlH3D6hI6BLVWNlrRQYFklpZK

Download the Mixly Code and PDF:
https://drive.google.com/open?id=1QFMQkdE19fnMpBHL657ze0H3Haj9H29j



Buy from