Ks0133 keyestudio EASY plug MQ135 Air Quality Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(7 intermediate revisions by the same user not shown)
Line 4: Line 4:
MQ135 sensor uses SnO2 sensitive material because SnO2 has low electrical conductivity in the clean air. <br>
MQ135 sensor uses SnO2 sensitive material because SnO2 has low electrical conductivity in the clean air. <br>
When surrounded by polluted air, the electrical conductivity of MQ135 sensor will increase with the increase of pollutants, and the change in electrical conductivity can be converted to corresponding output signal. <br>
When surrounded by polluted air, the electrical conductivity of MQ135 sensor will increase with the increase of pollutants, and the change in electrical conductivity can be converted to corresponding output signal. <br>
You can rotate the potentiometer on the sensor to adjust the sensitivity.<br>
You can rotate the potentiometer on the sensor to adjust the sensitivity. MQ135 has a high sensitivity to ammonia, sulfide, benzene vapor, smoke and other harmful gases.<br>
MQ135 has a high sensitivity to ammonia, sulfide, benzene vapor, smoke and other harmful gases.<br>
This module should be used together with EASY plug control board.<br>
<span style="color: red">'''Note: ''' this module should be used together with EASY plug control board.<br>
 
<span style=color:red> '''Special Note:''' <br>
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br>


<br>
<br>
==Features==
==Features==
*Interface: Easy plug
*Interface: Easy plug
Line 65: Line 68:
==What You Should See==
==What You Should See==
Done uploading the test code, open the serial monitor and set the baud rate to 9600, you should be able to see the “Gas leakage” and analog value.
Done uploading the test code, open the serial monitor and set the baud rate to 9600, you should be able to see the “Gas leakage” and analog value.
<br>[[File:Ks0133-4.png|600px|frameless|thumb]]  [[File:Ks0133 result.png|600px|frameless|thumb]]<br>
<br>[[File:Ks0133-4.png|700px|frameless|thumb]]  [[File:Ks0133 result.png|600px|frameless|thumb]]<br>


<br>
<br>


==Resources ==
==Resources ==
'''Download the PDF:'''<br>
https://drive.google.com/open?id=1pyThscSF3TAERFTrTj7xfPnUuO15KSsR


'''Download the Code:'''<br>
https://fs.keyestudio.com/KS0133
https://drive.google.com/open?id=1ZyuI9kgD-cFl9uK3tMqLUqj-ZIvEQqc8


<br>
<br>


==Buy from ==
==Buy from ==
*'''Official Website:''' http://www.keyestudio.com/ks0131.html
*[https://www.keyestudio.com/keyestudio-easy-plug-mq-135-air-quality-sensor-gas-detection-module-for-arduino-steam-p0099.html '''Official Website''' ]


*[https://www.aliexpress.com/store/product/NEW-Keyestudio-EASY-plug-Analog-Gas-Sensor-MQ-2-for-arduino-starter/1452162_32647755242.html?spm=2114.12010612.8148356.54.60624ba73cp1Lj  Shop on aliexpress ]
*[https://www.aliexpress.com/store/product/New-Keyestudio-EASY-plug-MQ-135-Air-Quality-Sensor-Module-for-arduino/1452162_32645593523.html?spm=2114.12010612.8148356.8.7ebe24eaqM2oiA  Shop on aliexpress ]


[[category:EASY Plug]]
[[category:EASY Plug]]

Latest revision as of 16:48, 7 January 2021

EASY plug MQ135 Air Quality Sensor

Introduction

MQ135 sensor uses SnO2 sensitive material because SnO2 has low electrical conductivity in the clean air. 
When surrounded by polluted air, the electrical conductivity of MQ135 sensor will increase with the increase of pollutants, and the change in electrical conductivity can be converted to corresponding output signal.
You can rotate the potentiometer on the sensor to adjust the sensitivity. MQ135 has a high sensitivity to ammonia, sulfide, benzene vapor, smoke and other harmful gases.
This module should be used together with EASY plug control board.

Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.


Features

  • Interface: Easy plug
  • Sensor type: Semiconductor
  • Operating voltage: 5V DC
  • Load resistance: Adjustable RL
  • Quick response and high sensitivity
  • Target gas: ammonia; methylbenzene; hydrogen


Technical Details

  • Dimensions: 56mm*20mm*18mm
  • Weight: 9.2g


Connect It Up

Connect the EASY Plug MQ135 sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.

int gas_din=2;
int gas_ain=A7;
int led=13;
int ad_value;
void setup()
{
  pinMode(led,OUTPUT);
  pinMode(gas_din,INPUT);
  pinMode(gas_ain,INPUT);
  Serial.begin(9600);
}
void loop()
{ 
  ad_value=analogRead(gas_ain);
  if(digitalRead(gas_din)==LOW)
  { 
    digitalWrite(led,HIGH);
    Serial.println("Gas leakage");
    Serial.println(ad_value);
  }
  else
  {
    digitalWrite(led,LOW);
Serial.println("Gas not leak");
    Serial.println(ad_value);
  }
  delay(500);
}


What You Should See

Done uploading the test code, open the serial monitor and set the baud rate to 9600, you should be able to see the “Gas leakage” and analog value.
thumb thumb


Resources

https://fs.keyestudio.com/KS0133


Buy from