Ks0243 keyestudio EASY plug W5100 Ethernet Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(5 intermediate revisions by the same user not shown)
Line 6: Line 6:
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.<br>  
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.<br>  
You don’t need to consider the Ethernet control, and just need simple program for ports.<br>
You don’t need to consider the Ethernet control, and just need simple program for ports.<br>
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.  
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.
<span style=color:red> '''Special Note:''' <br>
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br>


<br>
<br>
Line 87: Line 90:


==What You Should See==
==What You Should See==
Done uploading the test code, open the serial monitor and set the baud rate to 9600, you should be able to check the IP address that W5100 Ethernet module connected.  
Done uploading the test code, open the serial monitor and set the baud rate to 9600;<br>
you should be able to check the IP address that W5100 Ethernet module connected.  
<br>[[File:Ks0243-2.png|700px|frameless|thumb]]<br>
<br>[[File:Ks0243-2.png|700px|frameless|thumb]]<br>


Line 93: Line 97:


==Resources ==
==Resources ==
'''Download the PDF:'''<br>
https://drive.google.com/open?id=1p7rEYMu5YAaGPQpOddhlyCLMpdV5mDPl


'''Download the Code:'''<br>
'''Download the Code and libraries:'''<br>
https://drive.google.com/open?id=1BpRSrwKWN_ff6cEQ6xhqklH1shjVc4fQ
 
https://fs.keyestudio.com/KS0243


'''Download the libraries:'''<br>
https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG


<br>
<br>


==Buy from ==
==Buy from ==
*'''Official Website:'''  http://www.keyestudio.com/ks0243.html
*[https://www.keyestudio.com/keyestudio-easy-plug-w5100-ethernet-network-module-for-arduino-steam-p0061-p0061.html '''Official Website''' ]


*[https://www.aliexpress.com/store/product/Keyestudio-EASY-plug-W5100-Ethernet-network-Module-for-arduino/1452162_32822543545.html?spm=2114.12010612.8148356.3.14e424ea9BaqpD  Shop on aliexpress ]
*[https://www.aliexpress.com/store/product/Keyestudio-EASY-plug-W5100-Ethernet-network-Module-for-arduino/1452162_32822543545.html?spm=2114.12010612.8148356.3.14e424ea9BaqpD  Shop on aliexpress ]


[[category:EASY Plug]]
[[category:EASY Plug]]

Latest revision as of 08:36, 8 January 2021

EASY plug W5100 Ethernet Module

Introduction

W5100 is a multi-purpose single internet interface chip, integrated 10/100 Ethernet controller inside, and applied to embedded system which is high integration, high stability, high performance and low cost.
It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX.
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.
You don’t need to consider the Ethernet control, and just need simple program for ports.
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.

Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.


Specifications

  • Various interface: Direct Bus, Indirect Bus and SPI Bus
  • Supporting TCP/IP protocol stack of hardware, also TCP, UDP, ICMP, IGMP, IPv4, ARP and PPPoE
  • Up to 4 independent ports
  • Integrating 16KBYTE transmit-receive cache
  • Supporting automatic conversion of polarity
  • Coming with Internet access


Technical Details

  • Dimensions: 61mm*30mm*18mm
  • Weight: 14.1g


Connect It Up

Connect the EASY Plug W5100 Ethernet module to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.
Note: before compile the code, do remember to place the necessary libraries inside the libraries directory of Arduino IDE.
You can download the libraries from the link: https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG

#include <SPI.h>
#include <Ethernet.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); 

// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = {  
  0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };

// Initialize the Ethernet client library
// with the IP address and port of the server 
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;
void setup() {
  Serial.begin(9600);
  lcd.init();
  lcd.backlight();
}

void loop() {
 ///////////////////////////////////////////////////////////// W5100
 delay(1000); 
 lcd.clear();
 lcd.setCursor(0,0);
 lcd.print("T ..."); 
  if (Ethernet.begin(mac) == 0)  
  {
    lcd.setCursor(0,1);
    lcd.print("W5100 Error!");
    Serial.println("W5100 Error!");
    while(1);
  }
  lcd.setCursor(0,1);
  for (byte thisByte = 0; thisByte < 4; thisByte++) {
   lcd.print(Ethernet.localIP()[thisByte], DEC);
   lcd.print(".");
   Serial.print(Ethernet.localIP()[thisByte], DEC);
   Serial.print(".");
  }
  lcd.setCursor(14,1);
  lcd.print("OK");  
  Serial.println("OK");
  //while(1);
}


What You Should See

Done uploading the test code, open the serial monitor and set the baud rate to 9600;
you should be able to check the IP address that W5100 Ethernet module connected.
thumb


Resources

Download the Code and libraries:

https://fs.keyestudio.com/KS0243



Buy from