Ks0243 keyestudio EASY plug W5100 Ethernet Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
==EASY plug W5100Ethernet Module==
[[image:Ks0243-.png|thumb|600px|right|EASY plug W5100 Ethernet Module ]]
<br>[[File:KS0243-1.png|500px|frameless|thumb]]<br>


==Introduction==
W5100 is a multi-purpose single internet interface chip, integrated 10/100 Ethernet controller inside, and applied to embedded system which is high integration, high stability, high performance and low cost. <br>
It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX. <br>
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.<br>
You don’t need to consider the Ethernet control, and just need simple program for ports.<br>
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.
<span style=color:red> '''Special Note:''' <br>
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br>


==Introduction==
<br>
The EASY plug W5100 ethernet module needs to be used with the EASY plug Control board V2.0 control board. The module is connected to the SPI communication interface with only one line, so the wiring is done in a simple and convenient way. W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet controller inside,and applied to embedded system which is high integration, high stability, high performance and low cost. It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX. It contains TCP/IP protocol stack that is full-hardware and verified by market for years, ethernet medium transport layer and physical layer. You don’t need to consider the control of ethernet, and just need simple program of ports.<br>
<br>[[File:KS0243.jpg|500px|frameless|thumb]]<br>


==Specification==
==Specifications==
* Various interface: Direct Bus, Indirect Bus and SPI Bus
* Various interface: Direct Bus, Indirect Bus and SPI Bus
* Supporting TCP/IP protocol stack of hardware, also TCP,UDP,ICMP,IGMP,IPv4,ARP and PPPoE  
* Supporting TCP/IP protocol stack of hardware, also TCP, UDP, ICMP, IGMP, IPv4, ARP and PPPoE  
* Up to 4 independent ports
* Up to 4 independent ports
* Integrating 16KBYTE transmit-receive cache
* Integrating 16KBYTE transmit-receive cache
* Supporting automatic conversion of polarity
* Supporting automatic conversion of polarity
* Coming with Internet access, dual row of 2*14 2.0mm pins
* Coming with Internet access
<br>


==Technical Details==
* Dimensions: 61mm*30mm*18mm
* Weight: 14.1g
<br>


==Connection Diagram ==
==Connect It Up==
<br>[[File:KS0243-2.png|500px|frameless|thumb]]<br>
Connect the EASY Plug W5100 Ethernet module to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
<br>[[File:Ks0243-3.png|700px|frameless|thumb]]<br>
 
<br>
 
==Upload the Code==
Copy and paste below code to [http://wiki.keyestudio.com/index.php/How_to_Download_Arduino_IDE Arduino IDE] and upload.  <br>
<span style=color:red> '''Note:''' before compile the code, do remember to place the necessary libraries inside the libraries directory of Arduino IDE. </span><br>
You can download the libraries from the link: https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG


==Sample Code==
<pre>
<pre>
#include <SPI.h>
#include <SPI.h>
#include <Ethernet.h>
#include <Ethernet.h>
#include <Wire.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
#include <LiquidCrystal_I2C.h>
Line 69: Line 86:
}
}
</pre>
</pre>
Download Address of Libraries:<br>
http://7326097.s21d-7.faiusrd.com/0/ABUIABAAGAAgs4zWvQUokJuN5wU?f=KS0148+Libraries.zip&v=1471514163


==Test Result==
<br>
After connecting the power and burning code, please open the serial monitor, and set 9600 baud rate, you can see the IP address of the network line connected to the EASY plug W5100 ethernet module, as the diagram shown below.
 
<br>[[File:KS0243-3.png|500px|frameless|thumb]]<br>
==What You Should See==
Done uploading the test code, open the serial monitor and set the baud rate to 9600;<br>
you should be able to check the IP address that W5100 Ethernet module connected.  
<br>[[File:Ks0243-2.png|700px|frameless|thumb]]<br>
 
<br>


==Resources ==
==Resources ==


'''File:''' <br>
'''Download the Code and libraries:'''<br>
https://drive.google.com/open?id=1p7rEYMu5YAaGPQpOddhlyCLMpdV5mDPl
 
https://fs.keyestudio.com/KS0243
 
 
<br>


==Buy from ==
==Buy from ==
'''Official Website'''
*[https://www.keyestudio.com/keyestudio-easy-plug-w5100-ethernet-network-module-for-arduino-steam-p0061-p0061.html '''Official Website''' ]


http://www.keyestudio.com/easy-plug-w5100ethernet-module.html
*[https://www.aliexpress.com/store/product/Keyestudio-EASY-plug-W5100-Ethernet-network-Module-for-arduino/1452162_32822543545.html?spm=2114.12010612.8148356.3.14e424ea9BaqpD  Shop on aliexpress ]


[[Category:Module]]
[[category:EASY Plug]]

Latest revision as of 08:36, 8 January 2021

EASY plug W5100 Ethernet Module

Introduction

W5100 is a multi-purpose single internet interface chip, integrated 10/100 Ethernet controller inside, and applied to embedded system which is high integration, high stability, high performance and low cost.
It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX.
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.
You don’t need to consider the Ethernet control, and just need simple program for ports.
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.

Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.


Specifications

  • Various interface: Direct Bus, Indirect Bus and SPI Bus
  • Supporting TCP/IP protocol stack of hardware, also TCP, UDP, ICMP, IGMP, IPv4, ARP and PPPoE
  • Up to 4 independent ports
  • Integrating 16KBYTE transmit-receive cache
  • Supporting automatic conversion of polarity
  • Coming with Internet access


Technical Details

  • Dimensions: 61mm*30mm*18mm
  • Weight: 14.1g


Connect It Up

Connect the EASY Plug W5100 Ethernet module to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.
Note: before compile the code, do remember to place the necessary libraries inside the libraries directory of Arduino IDE.
You can download the libraries from the link: https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG

#include <SPI.h>
#include <Ethernet.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); 

// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = {  
  0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };

// Initialize the Ethernet client library
// with the IP address and port of the server 
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;
void setup() {
  Serial.begin(9600);
  lcd.init();
  lcd.backlight();
}

void loop() {
 ///////////////////////////////////////////////////////////// W5100
 delay(1000); 
 lcd.clear();
 lcd.setCursor(0,0);
 lcd.print("T ..."); 
  if (Ethernet.begin(mac) == 0)  
  {
    lcd.setCursor(0,1);
    lcd.print("W5100 Error!");
    Serial.println("W5100 Error!");
    while(1);
  }
  lcd.setCursor(0,1);
  for (byte thisByte = 0; thisByte < 4; thisByte++) {
   lcd.print(Ethernet.localIP()[thisByte], DEC);
   lcd.print(".");
   Serial.print(Ethernet.localIP()[thisByte], DEC);
   Serial.print(".");
  }
  lcd.setCursor(14,1);
  lcd.print("OK");  
  Serial.println("OK");
  //while(1);
}


What You Should See

Done uploading the test code, open the serial monitor and set the baud rate to 9600;
you should be able to check the IP address that W5100 Ethernet module connected.
thumb


Resources

Download the Code and libraries:

https://fs.keyestudio.com/KS0243



Buy from