Ks0271 keyestudio OLED Display OLED Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 72: Line 72:
'''Four Libraries of OLED Display Module:'''  <br>
'''Four Libraries of OLED Display Module:'''  <br>
https://drive.google.com/open?id=1VneczfQemtHSrRf4cDYMrZlclz55CR7l
https://drive.google.com/open?id=1VneczfQemtHSrRf4cDYMrZlclz55CR7l
'''VIDEO:''' <br>
http://www.keyestudio.com/wp/2018/01/ks0271-keyestudio-oled-display-oled-module/


==Buy from ==
==Buy from ==

Revision as of 14:42, 16 January 2018

Keyestudio OLED Display OLED Module


thumb

Introduction

OLED is short for organic light emitting diode. On the microscopic level, an OLED display is a matrix of organic LEDs that light up when they emit energy. Old LCD (Liquid Crystal Display) technology uses electronically controlled polarizers to change the way light passes or does not pass through them. This requires an external backlight that lights up the whole display underneath. This uses a lot of energy because at the time the display is on, enough light for all pixels must be provided. The new OLED technology only uses electricity per pixel. Because each pixel creates its own light, only the pixels that are on use electricity. This makes OLED technology very efficient; also, the way these types of OLEDs are built allows them to be very thin compared to LCD.

Specification

  • Supply Voltage: 3.3V to 5V
  • Number of Pixels:128 × 64
  • Color Depth:blue
  • Communication way: IIC


thumb

Connection Diagram


thumb

Sample Code

#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

#define OLED_RESET 4
Adafruit_SSD1306 display(OLED_RESET);

void setup() {

// by default, we'll generate the high voltage from the 3.3v line internally! (neat!)
display.begin(SSD1306_SWITCHCAPVCC, 0x3C); // initialize with the I2C addr 0x3D (for the 128x64)
// init done

// Show image buffer on the display hardware.
// Since the buffer is intialized with an Adafruit splashscreen
// internally, this will display the splashscreen.
display.display();
delay(2000);

// Clear the buffer.
display.clearDisplay();
}

void loop() {

display.clearDisplay();
display.setTextSize(1);
display.setTextColor(WHITE);
display.setCursor(0,0);
display.println("Hello,world!");
display.println("Hello,keyestudio!");
display.setTextSize(2);
display.println("Hello!");
display.println("keyes!");
display.println("keyestudio");
display.display();
delay(250);
}

Result

Wiring as the above diagram and burning the code, after power-on, OLED display will as the graph shown below.


thumb


Resource

PDF File:
https://drive.google.com/open?id=1ksYXWqnel7kQjDK1c9mCSRpW6FphaOay

Four Libraries of OLED Display Module:
https://drive.google.com/open?id=1VneczfQemtHSrRf4cDYMrZlclz55CR7l

VIDEO:
http://www.keyestudio.com/wp/2018/01/ks0271-keyestudio-oled-display-oled-module/

Buy from

Official Website

http://www.keyestudio.com/keyestudio-oled-display-oled-module.html