KS0311 Keyestudio CNC V0.9A+4988 Driver with Heat Sink Kit

From Keyestudio Wiki
Jump to navigation Jump to search


Keyestudio CNC V0.9A+4988 Driver with Heat Sink Kit



Introduction

This kit mainly includes a keyestudio CNC V0.9A, three A4988 driver modules with heat sink and a USB cable.
Keyestudio CNC GRBL V0.9 is a main board developed by Keyestudio for CNC, laser engraving machine, writing robots and other robots. It has complete interfaces with cost-effective and can be driven via external connection, suitable for DIY and factory use.
The A4988 module is a DMOS microstepping driver with converter and overcurrent protection, which can operate a bipolar stepper motor in full, half, 1/4, 1/8 and 1/16 step modes, with output-driven performance up to 35 V and ± 2A. The A4988 also includes a fixed off-time current regulator that operates in slow or mixed-decay modes.


thumb


Specifications of CNC V0.9A

  • Microprocessor:MEGA328p
  • Input Voltage:DC 12V
  • Supporting File Format:Gcode
  • Supporting Machine Structure:CNC, laser engraving machine, writing robots


thumb


Features of A4988 Driver

  • With simple stepper and direction control interface.
  • Five different step modes: full, half, 1/4, 1/8 and 1/16 step modes.
  • Adjustable potentiometer used to adjust the max current output to gain higher step rate.
  • Automatic decay mode detection/selection.
  • Overheat closed circuit, under-voltage lockout, cross-current protection.
  • Ground short-circuit protection and load short-circuit protection.


thumb


Pinout Diagram

Here in the below figure you can see the pinout instruction of keyestudio CNC GRBL V0.9
It has complete interfaces with cost-effective, and can connect to external drivers, very suitable for your DIY design.

thumb


Setting Method of A4988 Working Mode


thumb


Wiring Diagram


thumb


Install Driver Software and Development Environment Software IDE


(1) Install Diver Software

For different operating system, there may be slight difference in installation method. Below is an example in WIN 7.
a. When you connect Keyestudio CNC GRBL V0.9 to your computer the first time, right click “Computer” —>“Properties”—> “Device manager”, you can see “USB2.0-Serial”.
thumb

b. Click “USB2.0-Serial”, select “Update Driver software”.
thumb

c. In this page, click “Browse my computer for driver software”.
thumb

d. Find the “usb_ch341_3.1.2009.06” file.
thumb

e. Click “Next”, Installation completed; Then,click “Close”.
thumb

f. After driver is installed, go to “Device manager” again. right click “Computer” —> “Properties”—> “Device manager”, you can see device as below figure shown, also the correct Com port.
thumb


(2) Install Development Environment Software IDE

a. Double click arduino-1.5.6-r2-windows to start. Select “I Agree”to accept license agreement.
thumb

b. Select components to install and click “Next”.
thumb

c. Click “Browse” and select another folder. Click “Install” to start the installation.
thumb

d. Finally, wait for a few minutes to finish.
thumb


Testing Method

Wire it up well as wiring diagram shown, upload the below code to Keyestudio CNC GRBL V0.9 using Arduino IDE . Then you can check the function of each interface.


Sample Code

#define Light1  13 
#define Light2  A1 
#define Light3  A2 
#define Light4  A3
#define Light5  A4
#define Light6  A5

#define EN1  8
#define X_DIR     5       //X axis  direction control of stepper motor
#define Y_DIR     6       //y axis  direction control of stepper motor
#define Z_DIR     7       //z axis  direction control of stepper motor
#define X_STP     2       //x axis step control
#define Y_STP     3       //y axis step control
#define Z_STP     4       //z axis step control
#define X_LIMIT   9       //X limit
#define Y_LIMIT   10      //Y limit
#define Laser     11      //motor or laser control pin
#define Z_LIMIT   12      //Z limit
#define E_LIMIT   A0      //E limit
const int Button_A7 = A7;
const int Button_A6 = A6;
int Button_value_A7 = 0; 
int Button_value_A6 = 0; 
int Button_valueX = 0; 
int Button_valueY = 0;
int Button_valueZ = 0;
int Button_valueE = 0;

void setup() {
  pinMode(Light1, OUTPUT);    pinMode(Light2, OUTPUT);
  pinMode(Light3, OUTPUT);    pinMode(Light4, OUTPUT);
  pinMode(Light5, OUTPUT);    pinMode(Light6, OUTPUT);
  
  pinMode(EN1, OUTPUT);
  pinMode(X_DIR, OUTPUT);
  pinMode(Y_DIR, OUTPUT);
  pinMode(Z_DIR, OUTPUT);
  pinMode(X_STP, OUTPUT);
  pinMode(Y_STP, OUTPUT);
  pinMode(Z_STP, OUTPUT);
  pinMode(Button_A7, INPUT);  
  pinMode(Button_A6, INPUT); 
  pinMode(E_LIMIT, INPUT); 
  pinMode(X_LIMIT, INPUT); 
  pinMode(Y_LIMIT, INPUT); 
  pinMode(Z_LIMIT, INPUT); 
  Serial.begin(9600);
}

void EN()
{
  digitalWrite(EN1, LOW); 
}
//stepper motor turn forward or reverse
void turn(boolean dir, int steps)
{
  EN();
  digitalWrite(X_DIR,dir);
  digitalWrite(Y_DIR,dir);
  digitalWrite(Z_DIR,dir);
  delay(100);
  for(int i=0;i<steps;i++)
  {
    digitalWrite(X_STP, HIGH);
    digitalWrite(Y_STP, HIGH);
    digitalWrite(Z_STP, HIGH);
    delayMicroseconds(100);
    digitalWrite(X_STP, LOW);
    digitalWrite(Y_STP, LOW);
    digitalWrite(Z_STP, LOW);
    delayMicroseconds(100); 
   }
}
//laser is on
void Laser_ON()
{
  digitalWrite(Laser, HIGH); 
  delay(500);
  //digitalWrite(Laser, LOW); 
  //delay(500);
}
//laser is off
void Laser_OFF()
{
  digitalWrite(Laser, LOW); 
  delay(500);
  //digitalWrite(Laser, LOW); 
  //delay(500);
}

void loop() 
{
  
  Button_valueX = digitalRead(X_LIMIT);
  if(Button_valueX == LOW)  
  {
    digitalWrite(Light3, HIGH);
    turn(true, 4000);
  }
  else 
  {
    digitalWrite(Light3, LOW);
  }
  Serial.print("Button_valueX = ");
  Serial.println(Button_valueX);
  
  Button_valueY = digitalRead(Y_LIMIT);
  if(Button_valueY == LOW)  
  {
    digitalWrite(Light4, HIGH);
    turn(false, 4000);
  }
  else digitalWrite(Light4, LOW);
  Serial.print("Button_valueY = ");
  Serial.println(Button_valueY);
  
  Button_valueZ = digitalRead(Z_LIMIT);
  if(Button_valueZ == LOW)  digitalWrite(Light5, HIGH);
  else digitalWrite(Light5, LOW);
  Serial.print("Button_valueZ = ");
  Serial.println(Button_valueZ);
  
  Button_value_A7 = analogRead(Button_A7);
  if(Button_value_A7 == 0)  digitalWrite(Light1, HIGH);
  else digitalWrite(Light1, LOW);
  Serial.print("Button_value_A7 = ");
  Serial.println(Button_value_A7);
  
  Button_value_A6 = analogRead(Button_A6);
  if(Button_value_A6 == 0)  digitalWrite(Light2, HIGH);
  else digitalWrite(Light2, LOW);
  Serial.print("Button_value_A6 = ");
  Serial.println(Button_value_A6);   
  
  Button_valueE = analogRead(E_LIMIT);
  if(Button_valueE == 0)  
  {
    digitalWrite(Light6, HIGH);
    Laser_ON();
  }
  else 
  {
    digitalWrite(Light6, LOW);
    Laser_OFF();
  }
  Serial.print("Button_valueE = ");
  Serial.println(Button_valueE);    
}



Install Firmware and Grbl Controller


a. Write test program to keyestudio UNO R3
copy the folder GRBL_ Arduino_Library_keyes in the data packet and paste it to the folder libraries in your Arduino IDE document installation.

Code:

#include <grblmain.h>
void setup(){
startGrbl();
}
void loop(){}
//Burn the code above to keyestudio UNO R3


b. Install GrblController361 Software
Grbl Controller is a piece of software which is used to send GCode to CNC Machines. Run Grbl Controller361 Setup in your installation packet, the interface below will come out:
Click Next to continue.
thumb

For a license agreement, please check I accept the agreement and click Next.
thumb

When you are ready to continue with Setup, click Next.
thumb

To continue, click Next. If you would like to select a different folder to install, click Browse.
thumb

To continue, click Next. If you would like to select a different folder to place program’s shortcuts, click Browse.
thumb

Select the additional tasks you would like Setup to perform while installing Grbl Controller, then click Next.
thumb

Click Install to continue with the installation.
thumb

Click Next.
thumb

At last, click ”Finish” to finish the installation.
thumb
At last, click ”Finish” to finish the installation.


c. Test G-Code on Grbl Controller
Power the main board using a USB cable and connect correctly all your external devices, then run Grbl Controller.
Choose Port name the same as IDE COM port and click “Open” to open the series port, connecting CNC Machines with computer.

thumb

After opening the series port, the “Open” button change into “Close/Reset” and get red!
At this time you can click the X axis、Y axis、Z axis as shown in below diagram to adjust the motion direction of motors.

thumb

Note: after adjusting the axies, before beginning G-Code file, you must close and open again.
Now, it is time to have a try! Click ”Choose file” to choose one G-Code file named cn. to test in the data packet for a beginner, and the interface will come out:
GrblController
thumb

Click “Begin” , and you can see how the motors move on coordinates.




Resources

  • Test Code:

https://fs.keyestudio.com/KS0311



Get One Now