View source for Ks0113 keyestudio EASY plug Capacitive Touch Sensor

[[image:ks0113图.jpg|thumb|600px|right|EASY plug Capacitive Touch Sensor ]]

==Introduction==
You can find touch sensors mostly on electronic device. Instead of buttons, upgrade your Arduino project with our new version touch sensor and make it cool!<br>
The EASY Plug digital capacitive touch sensor provides a one-touch style switch on your Arduino project. It uses the most popular capacitive sensing technology which is the same as your mobile phone.<br>
This little sensor can "feel" people and metal touch and feedback a high/low voltage level. Even isolated by some cloth and paper, it can still feel the touch. The sensitivity will decrease as the isolation getting thick.<br>
<span style="color: red">'''Note: ''' this module should be used together with EASY plug control board.<br>
<br>

==Features==
* Connector: Easy plug
* Supply Voltage: 3.3V to 5V
* Sensor type: Digital
* Function range: 0℃ to 100℃

<br>
==Technical Details==
* Dimensions: 45mm*20mm*18mm
* Weight: 4.9g

<br>
==Connect It Up ==
Connect the EASY Plug touch sensor and LED module to control board using RJ11 cable. Then connect the control board to your PC with a USB cable.
<br>[[File:触摸灯.jpg|500px|frameless|thumb]]<br>

<br>
==Upload the Code==
<br>
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<br>[[File:ks0398 6.1.png|500px|frameless|thumb]]<br>

<br>

==What You Should See==
Done uploading the code, when you touch the sensor, the led on the sensor will light up.
<br>[[File:ks0398 6-3.png|500px|frameless|thumb]]<br>
<br>
Open the monitor, it will print out the value read from the touch sensor.
<br>[[File:ks0398 6-2.png|500px|frameless|thumb]]<br>

<br>
==Simulating Table Lamp==
<br>
'''Test Code'''
<br>[[File:ks0398 6.2.png|600px|frameless|thumb]]<br>

'''What You Should See'''<br>
Powered up and upload well the code, press down the button, LED light is turned on, it will not be off when release the button; But if press the button once again, LED will be turned off. It seems like your table lamp. <br>
<br>[[File:ks0398 6-5.png|500px|frameless|thumb]]<br>
<br>
Open the monitor, you should be able to see how many times do you touch the sensor.
<br>[[File:ks0398 6-4.png|500px|frameless|thumb]]<br>

<br>
<span style="color: red">'''Troubleshooting:'''</span> <br>
* '''Program Not Uploading?'''<br>
This happens sometimes, the most likely case is a confused Board and serial port, you should firstly select your proper board and port. <br>
If it doesn’t, make sure you have assembled the circuit correctly and verified and uploaded the code to your board. <br>
<br>[[File:ks0398 6-6.png|500px|frameless|thumb]]<br>


<br>

==Resources ==
'''Download the Arduino Code and PDF:'''<br>
https://drive.google.com/open?id=10luKx7DptrQL7HQWbqv09luzkSEcnx3t

'''Download the Mixly Code and PDF:'''<br>
https://drive.google.com/open?id=1mt5oiId-4T5VWi4eEaB7Zuf-97bNwMFB

<br>

==Buy from ==
*[https://www.keyestudio.com/new-keyestudio-easy-plug-capacitive-touch-sensor-for-arduino-starter-steam-p0088-p0088.html  '''Official Website''' ]

*[https://www.aliexpress.com/store/product/New-Keyestudio-EASY-Plug-Capacitive-Touch-Sensor-for-Arduino-starter/1452162_32641589449.html?spm=2114.12010612.8148356.2.2d5b57f6LCLmWc   Shop on aliexpress ]


[[category:EASY Plug]]