View source for Ks0255 keyestudio Bluetooth 4.0 Expansion Shield

==Keyestudio Bluetooth 4.0 Expansion Shield ==
<br>[[File:Ks0255 bluetooth 4.0.png|500px|frameless|thumb]]<br>

==Introduction==

Keyestudio Bluetooth 4.0 shield integrates sensor expansion board with HM -10 Bluetooth 4.0. It is fully compatible with keyestudio UNO R3 control board, which can work only through stacking the expansion board on the keyestudio UNO R3 control board, easy and convenient. It extends all digital ports and analog ports of keyestudio UNO R3 control board in the form of steering gear sequence. A sensor only needs a universal 3P sensor cable, which is very simple and fast. <br>
Expansion board with HM -10 Bluetooth 4.0 can be used for the bluetooth communication, and toggle switch control the power supply for Bluetooth. There is a jumper cap set on the board, and the default jumper wire achieves the direct communications between bluetooth module and keyestudio UNO R3 control board serial port. If the jumper cap connects another two jumper wires, achieving a serial port communication needs the keyestudio UNO R3 control board to set up the virtual serial port, which needs that the digital port 2 is set to RX, and digital port 3 is set to the TX.
<br>[[File:Ks0255 bluetooth shield.png|500px|frameless|thumb]]<br>

==Specification==
*Bluetooth protocol: Bluetooth Specification V4.0 BLE  <br>
*No byte limit in serial port Transceiving   <br>
*In open environment, realize 100m ultra-distance communication with iphone4s   <br>
*USB protocol: USB V2.0   <br>
*Working frequency: 2.4GHz ISM band   <br>
*Modulation method: GFSK(Gaussian Frequency Shift Keying)   <br>
*Transmission power: -23dbm, -6dbm, 0dbm, 6dbm, can be modified by AT command.   <br>
*Sensitivity: ≤-84dBm at 0.1% BER   <br>
*Transmission rate: Asynchronous: 6K bytes  ；Synchronous: 6k Bytes   <br>
*Security feature: Authentication and encryption <br>
*Supporting service: Central & Peripheral UUID FFE0, FFE1 <br>
*Power consumption: Auto sleep mode, stand by current 400uA~800uA, 8.5mA during  transmission.  <br>
*Power supply: 5V DC  <br>
*Working temperature: –5 to +65 Centigrade <br>

==Sample Code ==
<pre>
int val; 
int ledpin=13; 
void setup() 
{ 
Serial.begin(9600);
 pinMode(ledpin,OUTPUT); 
} void loop()
{ val=Serial.read(); 
if(val=='a')
 { 
digitalWrite(ledpin,HIGH); 
delay(250); 
digitalWrite(ledpin,LOW); 
delay(250);
 Serial.println("keyestudio");
}
}

</pre>

==Result==
The keyestudio Bluetooth 4.0 expansion board is stacked on the keyestudio UNO R3 control board. After the power is turned on, burn the procedure and dial the toggle switch to power on HM-10 Bluetooth - 4.0. Open APP HC-COM, click to search device and select the device;when the device is connected,the LED on the Bluetooth module is on. Enter “a” in HC-COM, click “Send”, Bluetooth APP will display keyestudio. Each time HC-COM sends an “a”, the Pin13 LED on the main board blinks once. 
<br>[[File:HC-COM.png|500px|frameless|thumb]]<br>

==Resources ==

'''PDF'''

https://drive.google.com/open?id=1i33cI2czppvA-U9-XF3EbRAOAL_0JbJ5

'''APP'''

https://drive.google.com/open?id=1Kkb33c7NDR6yeEaaYTn9KcXsSYQ3HeU6

==Get One Now ==
'''Official Websie'''

http://www.keyestudio.com/keyestudio-bluetooth-4-0-expansion-shield.html

[[Category: shield]]