View source for Ks0268 keyestudio SHT10 Digital Temperature Sensor


<br>
==Introduction==
Keyestudio SHT10 digital temperature sensor is a temperature and humidity composite sensor containing digital signal outputs calibration. <br>
It uses patented micromachining technology (CMOSens®) in the process of industrial COMS, which ensure that the product has high reliability and excellent long-term stability. <br>
Sensor has full scale calibration and two digital interface, which can be directly connected with the microcontroller. <br> 
It has the features of high reliability, strong stability, rapid response, low power consumption, strong anti-interference and accurate dew point measurement and so on. <br>
<br>[[File:KS0268.jpg|500px|frameless|thumb]]<br>

<br>
==Specification==
* Working Voltage：5V（DC）
* Interface：4PIN 
* Humidity Measurement Range：0---100%RH
* Humidity Measurement Accuracy：±4.5%RH（20%---80%RH）
* Humidity Measurement Resolution：0.03%RH
* Temperature Measurement Range：-40---123.8℃
* Temperature Measurement Accuracy：±0.5℃ error（in 25℃），±0.9℃ error（among 0---40℃）
* Temperature Measurement Resolution：0.01℃

<br>
==Connection Diagram ==
<br>[[File:KS0268.png|700px|frameless|thumb]]<br>

<br>
==Sample Code==
<pre>
/* Lab10 - SHT1x serials (SHT10, SHT11, SHT15) Reading sample of hygrothermograph
 * 
 * Need to install SHT1x Library:
 *    [url]https://github.com/practicalarduino/SHT1x/[/url]
 */
 
#include <SHT1x.h>
 
// define SHT1x connection pin
#define dataPin  11
#define clockPin 10
 
// Initialize sht1x object
SHT1x sht1x(dataPin, clockPin);
 
void setup()
{
   Serial.begin(9600);
}
 
void loop()
{
  // declare three variables, representing temperature (Celsius), temperature (Fahrenheit) and humidity
  float temp_c, temp_f, humidity;
 
  // read SHT1x temperature and humidity value
  temp_c = sht1x.readTemperatureC();
  temp_f = sht1x.readTemperatureF();
  humidity = sht1x.readHumidity();
 
  // Output the temperature and humidity value to Serial Port
  Serial.print("Temperature: ");
  Serial.print(temp_c, 1);  // Show one after the decimal point
  Serial.print("C / ");
  Serial.print(temp_f, 1);  // Show one after the decimal point
  Serial.print("F. Humidity: ");
  Serial.print(humidity);
  Serial.println("%");
 
  delay(1000);
}
</pre>


<br>
==Result==
Wiring as the above diagram and burning the code,after powered-on, open the serial monitor, it will display the current test temperature and humidity, as the graph shown below. <br>
<br>[[File:KSO268-.png|500px|frameless|thumb]]<br>

<br>
==Resources ==

* '''Download Code and Library SHT1x：'''<br>
https://fs.keyestudio.com/KS0268

* '''VIDEO:'''<br>
http://video.keyestudio.com/ks0268/

<br>

==Buy from ==

*[https://www.keyestudio.com/keyestudio-sht10-digital-temperature-sensor-for-arduino-p0378-p0378.html     '''Official Website''' ]

*[https://www.aliexpress.com/store/product/Keyestudio-SHT10-Digital-Temperature-Sensor-for-Arduino/1452162_32822577340.html?spm=2114.12010615.8148356.1.1028d2386StSnZ       '''Shop on aliexpress''' ]

*[https://www.amazon.com/dp/B0793J31GN   '''Shop on amazon''' ]


[[Category:Sensor]]