KS(3001...3012)Assemble the Housing of Raspberry Pi 4 - Revision history

Keyestudio: /* Wire up */

2021-08-26T09:07:33Z

Wire up

← Older revision		Revision as of 09:07, 26 August 2021
Line 59:		Line 59:


	图		<br>[[File:图片13001-11.png\|500px\|frameless\|thumb]]<br>

2021-08-26T09:05:45Z

Prepare the following parts we need

← Older revision		Revision as of 09:05, 26 August 2021
Line 30:		Line 30:
	== Prepare the following parts we need ==		== Prepare the following parts we need ==

			<br>[[File:图片13001-6.png\|500px\|frameless\|thumb]]<br>
	图


Line 39:		Line 38:


	图		<br>[[File:图片13001-7.png\|500px\|frameless\|thumb]]<br>


	Don’t forget to screw the bottom.(figure 8)		Don’t forget to screw the bottom.(figure 8)

	图		<br>[[File:图片13001-8.png\|500px\|frameless\|thumb]]<br>


	== Paste Colloidal Particles ==		== Paste Colloidal Particles ==

2021-08-26T09:02:48Z

Detailed Steps

← Older revision		Revision as of 09:02, 26 August 2021
Line 14:		Line 14:


	图		<br>[[File:图片13001-2.png\|500px\|frameless\|thumb]]<br> (figure 1)
			<br>[[File:QQ图片202108261632.png\|500px\|frameless\|thumb]]<br> (figure 2)
			<br>[[File:图片13001-3.png\|500px\|frameless\|thumb]]<br> (figure 3)

	图

	图

	=== Assemble a Fan ===		=== Assemble a Fan ===
Line 25:		Line 24:
	Note: refer to the figure 4 and make fan’s back upward.		Note: refer to the figure 4 and make fan’s back upward.


			<br>[[File:图片13001-4.png\|500px\|frameless\|thumb]]<br>
			<br>[[File:图片13001-5.png\|500px\|frameless\|thumb]]<br> (figure 4)

	== Prepare the following parts we need ==		== Prepare the following parts we need ==

2021-08-26T08:56:43Z

Preparations：

← Older revision		Revision as of 08:56, 26 August 2021
Line 4:		Line 4:


	图		<br>[[File:图片13001-1.png\|500px\|frameless\|thumb]]<br>


	== Detailed Steps ==		== Detailed Steps ==

2021-08-26T08:30:50Z

← Older revision	Revision as of 08:30, 26 August 2021
Line 1:	Line 1:
		== Preparations： ==

		What you need:


		图


		== Detailed Steps ==
		=== Stick Heat Sink ===

		Take out three heat sinks and three thermal conductive adhesives.(figure 1) <br>
		Glue conductive adhesives on the heat sinks.(figure 2) <br>
		Then stick heat sinks to the Raspberry Pi 4.(figure 3) <br>


		图

		图

		图

		=== Assemble a Fan ===

		Fix the fan onto the housing with screws, as shown below;
		Note: refer to the figure 4 and make fan’s back upward.


		== Prepare the following parts we need ==


		图


		Cover the Raspberry Pi 4 with the housing
		And place the oval plastic board as follows;
		Screw them together. (figure 7)


		图

		Don’t forget to screw the bottom.(figure 8)

		图


		== Paste Colloidal Particles ==


		Then glue colloidal particles in the four grooves, as shown below;

		图
		图

		== Wire up ==

		Respectively attach the red wire, black wire of the fan to 5V and GND of the Raspberry Pi, as shown below:
		Note: don’t reverse the negative and positive poles of the fan.


		图

2021-08-26T08:25:54Z

Created blank page

New page