Ks0006 MEGA Sensor Shield V1: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
Line 1: Line 1:
[[image:ks0006.png|thumb|500px|right|Keyestudio keyestudio MEGA Sensor Shield V1]]
==Introduction==
==Introduction==
Have you met with these troubles? when connecting a couple of sensor modules to MEGA 2560 control board, sometimes power output interfaces are not enough, so need to use the breadboard and the wiring is rather troublesome.<br>
Now don’t worry about that. You can use this keyestudio MEGA sensor shield.<br>
It is fully compatible with MEGA 2560 control board, so that you can easily stack the MEGA sensor shield onto the MEGA 2560 control board. <br>
The shield comes with digital and analog interfaces in 3PIN (G V S), easy to connect the 3PIN sensor modules. Besides, it comes with communication pins of 2.54mm pin pitch, such as serial and SPI communication. <br>
It comes with a reset button and 2 signal indicators as well.<br>
Note: for the 3PIN interface, the voltage of Analog pins (labeled V) is 5V; while the voltage of Digital pins (labeled V) is VCC, that is, the voltage input via a blue terminal block, default by jumper connected, connecting the voltage to 5V on the shield.
<br>
==Features==
* Can be plugged into the MEGA 2560 control board
* Comes with a Reset button
* Comes with a power led and a D13 indicator
* Extends the digital and analog interface of MEGA into 3PIN
* Comes with a serial communication interface
* Extends an ICSP interface
* Extends a SPI interface
* Extends a URF01 interface
* Extends an APC220 interface
* Able to supply the voltage to sensor modules via the terminal block (jumper cap off)
<br>


MEGA Sensor Shield V1 is used for sensor expansion, with PCB metallurgical deposition process applied. In the design, all digital and analog interfaces are lead out in the form of steering gear line sequence with the main board, and the bluetooth mode communication interface, SD Card module communication interface, APC220 wireless RF module communication interface, and RBURFv1.1 ultrasonic sensor interface are applied. This independent lead-out design makes the sensor board more convenient and easier to use. <br>
==Controller Compatible==
For a beginner of Arduino, she or he do not have to have a headache for the complex circuit connection. This type of Sensor Board Shield simplify the circuit in the true sense to make the commonly used sensors easily connected. You need only a general 3pin sensor cable (both digital and analog cable) to connect a sensor and after finishing circuit connection, compile the corresponding Arduino prgram and download it to the Arduino MEGA controller to read the sensor data, or receive returning data of wireless module and finally finish your own interactive project.  <br>
*[http://wiki.keyestudio.com/index.php/Ks0002_keyestudio_Mega_2560_R3_Development_Board keyestudio MEGA 2560 R3 ]
[[File:ks0006.png]]


==Resources ==
<br>


'''Video'''
==Technical Details==
* '''Dimensions:''' 100mm x 54mm
* '''Weight (only MEGA sensor shield):''' 39.2g
<br>[[Image:ks0006 Details.jpg|800px|frameless]]<br>


http://www.keyestudio.com/wp/ks0006/
<br>


==Get One Now==
==PINOUT Instruction==
'''Official Website'''
<br>[[Image:图片1-ks0006 pinout.png|900px|frameless]]<br>


http://www.keyestudio.com/ks0006.html
<br>
==Example Use==
You can stack the MEGA sensor shield onto MEGA 2560 control board. Use the LCD, sensor module and jumper wires to build the circuit experiment. Like below.  
<br>[[Image:ks0006 result.jpg|800px|frameless]]<br>


'''ebay'''
<br>
==Resources ==
* [https://drive.google.com/open?id=1OQpXJuiNQQyqjr8FSWnem63mXX3SDr7Z  You can click here to download the PDF ]


https://www.ebay.com/itm/Keyestudio-MEGA-2560-V1-Sensor-Shield-Expansion-Board-for-Arduino-/132589177307
* '''Video:''' http://www.keyestudio.com/wp/ks0006/


<br>
==Get One Now==
* '''Official Website:''' http://www.keyestudio.com/ks0006.html
*[https://www.amazon.com/KEYESTUDIO-MEGA-Sensor-Shield-Arduino/dp/B0169YXYEY  '''Shop on amazon''' ]
*[https://www.ebay.com/itm/Keyestudio-MEGA-2560-V1-Sensor-Shield-Expansion-Board-for-Arduino-/132589177307    '''Shop on ebay'''  ]
*[https://www.aliexpress.com/store/product/Free-shipping-keyes-MEGA-sensor-shield-V1-0-dedicated-sensor-expansion-board-electronic-building-blocks-for/1452162_2042269441.html?spm=2114.12010612.8148356.16.6ce7276fysCXC8  '''Shop on aliexpress'''  ]




[[Category: Shield]]
[[Category: Shield]]

Revision as of 15:38, 14 September 2018

Keyestudio keyestudio MEGA Sensor Shield V1

Introduction

Have you met with these troubles? when connecting a couple of sensor modules to MEGA 2560 control board, sometimes power output interfaces are not enough, so need to use the breadboard and the wiring is rather troublesome.
Now don’t worry about that. You can use this keyestudio MEGA sensor shield.
It is fully compatible with MEGA 2560 control board, so that you can easily stack the MEGA sensor shield onto the MEGA 2560 control board.
The shield comes with digital and analog interfaces in 3PIN (G V S), easy to connect the 3PIN sensor modules. Besides, it comes with communication pins of 2.54mm pin pitch, such as serial and SPI communication.
It comes with a reset button and 2 signal indicators as well.
Note: for the 3PIN interface, the voltage of Analog pins (labeled V) is 5V; while the voltage of Digital pins (labeled V) is VCC, that is, the voltage input via a blue terminal block, default by jumper connected, connecting the voltage to 5V on the shield.


Features

  • Can be plugged into the MEGA 2560 control board
  • Comes with a Reset button
  • Comes with a power led and a D13 indicator
  • Extends the digital and analog interface of MEGA into 3PIN
  • Comes with a serial communication interface
  • Extends an ICSP interface
  • Extends a SPI interface
  • Extends a URF01 interface
  • Extends an APC220 interface
  • Able to supply the voltage to sensor modules via the terminal block (jumper cap off)


Controller Compatible


Technical Details

  • Dimensions: 100mm x 54mm
  • Weight (only MEGA sensor shield): 39.2g


Ks0006 Details.jpg


PINOUT Instruction


图片1-ks0006 pinout.png


Example Use

You can stack the MEGA sensor shield onto MEGA 2560 control board. Use the LCD, sensor module and jumper wires to build the circuit experiment. Like below.
Ks0006 result.jpg


Resources


Get One Now

Retrieved from "http://wiki.keyestudio.com/index.php?title=Ks0006_MEGA_Sensor_Shield_V1&oldid=11909"