Ks0116 keyestudio EASY plug Flame Sensor Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
Line 1: Line 1:
==EASY plug Flame Sensor Module==
[[image:ks0116图.jpg|thumb|600px|right|EASY plug Flame Sensor Module]]
<br>[[File:ks0116-1.png|500px|frameless|thumb]]<br>


==Introduction==
==Introduction==
This flame sensor can be used to detect fire or other lights whose wavelength stands at 760 nm ~ 1100 nm. In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.<br>
The flame sensor can be used to detect fire or other wavelength at 760nm ~1100nm light. <br>
Note: this module needs to be used together with EASY plug control board.<br>
In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.<br>
The potentiometer on the flame sensor can be used to adjust the sensitivity.<br>
<span style="color: red">'''Note: ''' this module should be used together with EASY plug control board.<br>


==Specification==
==Specification==
* Interface: Easy plug
* Connector: Easy plug
* Supply Voltage: 3.3V to 5V
* Supply Voltage: 3.3V to 5V
* Detection range: 500px (4.8V) ~ 2500px (1V)
* Detection range: 500px (4.8V) ~ 2500px (1V)
* Rang of Spectral Bandwidth: 760nm to 1100nm
* Spectral Bandwidth Range: 760nm ~ 1100nm
* Operating temperature: -25℃to 85℃
* Operating temperature: -25℃ to 85℃
* Sensor type: digital
* Sensor type: digital
* Size: 49*16.7mm
* Weight: 6g


==Connection Diagram ==
<br>
<br>[[File:ks0116-2.png|500px|frameless|thumb]]<br>
==Technical Details==
* Dimensions: 48mm*17mm*18mm
* Weight: 4.6g


<br>
==Connect It Up==
Connect the EASY Plug flame sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
<br>[[File:ks0116.jpg|500px|frameless|thumb]]<br>


==Sample Code==
<br>
==Upload the Code==
Copy and paste below code to [http://wiki.keyestudio.com/index.php/How_to_Download_Arduino_IDE Arduino IDE] and upload. 
<pre>
<pre>
const int flamePin = 12;     // the number of the flame pin
const int flamePin = 2;// flame pin
const int ledPin = 13;     // the number of the LED pin
const int ledPin = 13;// LED pin
// variables will change:
// variables will change:
int State = 0;         // variable for reading status
int State = 0; // variable for reading status
void setup() {
void setup() {
// initialize the LED pin as an output:
// initialize the LED pin as output:
pinMode(ledPin, OUTPUT);    
pinMode(ledPin, OUTPUT);
// initialize the pushbutton pin as an input:
// initialize the push button pin as input:
pinMode(flamePin, INPUT);  
pinMode(flamePin, INPUT);
}
}
void loop(){
void loop(){
// read the state of the value:
// read the state of the value:
State = digitalRead(flamePin);
State = digitalRead(flamePin);
if (State == HIGH) {  
if (State == HIGH) {
  // turn LED on:     
// turn LED on:     
  digitalWrite(ledPin, HIGH);
digitalWrite(ledPin, HIGH);
}
}
else {
else {
  // turn LED off:
// turn LED off:
  digitalWrite(ledPin, LOW);
digitalWrite(ledPin, LOW);
}
}
}
}
</pre>
</pre>
<br>
==What You Should See==
Done uploading the code, put a lighter close to the flame sensor. Once the sensor detects the flame, you should see the led light up. If isn’t, you are able to adjust the sensitivity by a potentiometer.
<br>[[File:ks0116 Result.png|500px|frameless|thumb]]<br>


<br>
==Resources ==
==Resources ==
 
'''PDF'''<br>
'''PDF'''
 
https://drive.google.com/open?id=1aGobmBGdVwTBZ99YIRtuCf7Kg8FZYUTN
https://drive.google.com/open?id=1aGobmBGdVwTBZ99YIRtuCf7Kg8FZYUTN


<br>
==Buy from ==
==Buy from ==
'''Official Website'''
'''Official Website'''<br>
http://www.keyestudio.com/keyestudio-easy-plug-flame-sensor-module-for-arduino.html


http://www.keyestudio.com/keyestudio-easy-plug-flame-sensor-module-for-arduino.html


[[category:EASY Plug]]
[[category:EASY Plug]]

Revision as of 09:19, 23 November 2018

EASY plug Flame Sensor Module

Introduction

The flame sensor can be used to detect fire or other wavelength at 760nm ~1100nm light.
In the fire-fighting robot game, the flame plays an important role in the probe, which can be used as the robot's eyes to find fire source.
The potentiometer on the flame sensor can be used to adjust the sensitivity.
Note: this module should be used together with EASY plug control board.

Specification

  • Connector: Easy plug
  • Supply Voltage: 3.3V to 5V
  • Detection range: 500px (4.8V) ~ 2500px (1V)
  • Spectral Bandwidth Range: 760nm ~ 1100nm
  • Operating temperature: -25℃ to 85℃
  • Sensor type: digital


Technical Details

  • Dimensions: 48mm*17mm*18mm
  • Weight: 4.6g


Connect It Up

Connect the EASY Plug flame sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Copy and paste below code to Arduino IDE and upload.

const int flamePin = 2;// flame pin
const int ledPin = 13;// LED pin
// variables will change:
int State = 0; // variable for reading status
void setup() {
// initialize the LED pin as output:
pinMode(ledPin, OUTPUT);
// initialize the push button pin as input:
pinMode(flamePin, INPUT);
}
void loop(){
// read the state of the value:
State = digitalRead(flamePin);
if (State == HIGH) {
// turn LED on:    
digitalWrite(ledPin, HIGH);
}
else {
// turn LED off:
digitalWrite(ledPin, LOW);
}
}


What You Should See

Done uploading the code, put a lighter close to the flame sensor. Once the sensor detects the flame, you should see the led light up. If isn’t, you are able to adjust the sensitivity by a potentiometer.
thumb


Resources

PDF
https://drive.google.com/open?id=1aGobmBGdVwTBZ99YIRtuCf7Kg8FZYUTN


Buy from

Official Website
http://www.keyestudio.com/keyestudio-easy-plug-flame-sensor-module-for-arduino.html