Ks0112 keyestudio EASY plug Digital Push Button: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(12 intermediate revisions by the same user not shown)
Line 1: Line 1:
==EASY plug Digital Push Button ==
[[image:ks0112图.jpg|thumb|600px|right|Keyestudio EASY plug Digital Push Button]]
<br>[[File:ks0112-1.png|500px|frameless|thumb]]<br>


==Introduction==
==Introduction==
This is a basic application module widely applied in Arduino, Raspberry Pi platforms. When the button is pressed, it outputs high level signal; when you release the button, it outputs low level signal. You can simply plug it into an IO port to have your first taste of Arduino.<br>
The EASY Plug Push-button module is a tidy little design that lets you control a DC power source using an everyday tactile button.<br>
Note: this module needs to be used together with EASY plug control board.<br>
This basic application module is widely applied to Arduino, Raspberry Pi platforms.<br>
When the button is pressed, it outputs HIGH level signal; if release the button, it outputs LOW level signal.<br>
You can simply connect to an IO port to have your first taste of Arduino.<br>
This sensor needs to be used together with EASY plug control board.<br>


<span style=color:red> '''Special Note:''' <br>
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br>
<br>


==Specification==
==Specification==
* Interface: Easy plug
* Connector: Easy plug
* Supply Voltage: 3.3V to 5V
* Supply Voltage: 3.3V to 5V
* Large button keypad and high-quality first-class cap
* Large button and high-quality top cap
* Standard assembling structure (two 3mm diameter holes with multiple of 5mm as distance from center)
* Sensor type: Digital
* Sensor type: Digital
* Size: 38*20mm
* Weight: 6g


<br>
==Technical Details==
* Dimensions: 38mm*20mm*18mm
* Weight: 5.6g
<br>
==Connect It Up==
Connect the EASY Plug push button sensor and LED module to control board using RJ11 cables. <br>
<br>[[File:按键灯.jpg|500px|frameless|thumb]]<br>
<br>
==Example 1: Button Controlled Light==
<br>
'''Upload the Code'''<br>
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<br>[[File:ks0397 4.1.png|500px|frameless|thumb]]<br>


==Connection Diagram ==
<br>
<br>[[File:ks0112-2.png|500px|frameless|thumb]]<br>
'''What You Should See'''<br>
Powered up and upload well the code, press down the button, LED module is turned on. While release the button, LED is off.
<br>[[File:ks0397 4-1.png|500px|frameless|thumb]]<br>
<br>[[File:ks0397 4-3.png|500px|frameless|thumb]]<br>
<br>
Open the monitor, it will print out the value read from the button.
<br>[[File:ks0397 4-2.png|500px|frameless|thumb]]<br>




==Sample Code==
<br>
<pre>
==Example 2: Simulating Table Lamp==
/* # When you push the digital button, the Led 13 on the board will turn on. Otherwise,the led turns off.
<br>
*/
'''Upload the Code'''<br>
int ledPin = 13;                // choose the pin for the LED
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly Mixly Blocks] and upload.
int inputPin = 11;              // Connect sensor to input pin 11
<br>[[File:ks0397 4.2.png|600px|frameless|thumb]]<br>
void setup() {
pinMode(ledPin, OUTPUT);      // declare LED as output
pinMode(inputPin, INPUT);    // declare pushbutton as input
}
void loop(){
  int val = digitalRead(inputPin);  // read input value
if (val == HIGH) {            // check if the input is HIGH
  digitalWrite(ledPin, LOW);  // turn LED OFF
} else {
  digitalWrite(ledPin, HIGH); // turn LED ON
}
}
</pre>


<br>
'''What You Should See'''<br>
Powered up and upload well the code, press down the button, LED light is turned on, it will not be off when release the button; But if press the button once again, LED will be turned off. It seems like your table lamp. <br>
<br>[[File:ks0397 4-5.png|500px|frameless|thumb]]<br>
<br>
Open the monitor, you should be able to see how many times do you press the button.
<br>[[File:ks0397 4-4.png|500px|frameless|thumb]]<br>
<br>
<br>
==Resources ==
==Resources ==


'''PDF'''
https://fs.keyestudio.com/KS0112
<br>


https://drive.google.com/open?id=1n231PI2jg8BQcIFIccbpYRfGLHEpQoP0
==Buy from ==
*[https://www.keyestudio.com/new-keyestudio-easy-plug-digital-push-button-module-for-arduino-steam-p0091-p0091.html '''Official Website''' ]


==Buy from ==
*[https://www.aliexpress.com/store/product/New-Keyestudio-EASY-Plug-Digital-Push-Button-for-Arduino/1452162_32643204056.html?spm=2114.12010612.8148356.10.64de484e0lsdsr  Shop on aliexpress]
'''Official Website'''


http://www.keyestudio.com/keyestudio-easy-plug-digital-push-button-for-arduino.html


[[category:Module]]
[[category:EASY Plug]]

Latest revision as of 16:12, 7 January 2021

Keyestudio EASY plug Digital Push Button

Introduction

The EASY Plug Push-button module is a tidy little design that lets you control a DC power source using an everyday tactile button.
This basic application module is widely applied to Arduino, Raspberry Pi platforms.
When the button is pressed, it outputs HIGH level signal; if release the button, it outputs LOW level signal.
You can simply connect to an IO port to have your first taste of Arduino.
This sensor needs to be used together with EASY plug control board.

Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.


Specification

  • Connector: Easy plug
  • Supply Voltage: 3.3V to 5V
  • Large button and high-quality top cap
  • Sensor type: Digital


Technical Details

  • Dimensions: 38mm*20mm*18mm
  • Weight: 5.6g


Connect It Up

Connect the EASY Plug push button sensor and LED module to control board using RJ11 cables.

thumb


Example 1: Button Controlled Light


Upload the Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See
Powered up and upload well the code, press down the button, LED module is turned on. While release the button, LED is off.
thumb

thumb

Open the monitor, it will print out the value read from the button.
thumb



Example 2: Simulating Table Lamp


Upload the Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.
thumb


What You Should See
Powered up and upload well the code, press down the button, LED light is turned on, it will not be off when release the button; But if press the button once again, LED will be turned off. It seems like your table lamp.

thumb

Open the monitor, you should be able to see how many times do you press the button.
thumb



Resources

https://fs.keyestudio.com/KS0112

Buy from

Retrieved from "http://wiki.keyestudio.com/index.php?title=Ks0112_keyestudio_EASY_plug_Digital_Push_Button&oldid=30640"