Ks0246 keyestudio EASY plug Steam Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
 
(9 intermediate revisions by the same user not shown)
Line 5: Line 5:
<span style="color: red">'''Warning: ''' The connector is not waterproof, please be careful not to put the connector directly in water. </span><br>
<span style="color: red">'''Warning: ''' The connector is not waterproof, please be careful not to put the connector directly in water. </span><br>
The module can be connected to the analog input interface with only one line, which is very easy and convenient.  
The module can be connected to the analog input interface with only one line, which is very easy and convenient.  
<span style=color:red> '''Special Note:''' <br>
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br>
<br>
<br>


Line 18: Line 22:
* Dimensions: 35mm*24mm*18mm
* Dimensions: 35mm*24mm*18mm
* Weight: 4.6g
* Weight: 4.6g
<br>
<br>
==Connect It Up ==
==Connect It Up ==
Connect the EASY Plug steam sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
Connect the EASY Plug steam sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
Line 26: Line 30:
<br>
<br>
==Upload the Code==
==Upload the Code==
Copy and paste below code to [http://wiki.keyestudio.com/index.php/How_to_Download_Arduino_IDE Arduino IDE] and upload.  
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<pre>
<br>[[File:ks0397 16.1.png|500px|frameless|thumb]]<br>
void setup()
 
{
Serial.begin(9600); //open serial port, and set baud rate at 9600bps
}
void loop()
{
int val;
val=analogRead(0); //plug vapor sensor into analog port 0
Serial.print("Moisture is ");
Serial.println(val,DEC); //read analog value printed on serial port
delay(100);
}
</pre>
<br>
<br>
==What You Should See==
==What You Should See==
When detect the different degree of humidity, the sensor outputs different value. If the sensor’s sensing area detects a water drop, the analog value will be displayed on monitor window.
When detect the different degree of humidity, the sensor outputs different value. If the sensor’s sensing area detects a water drop, the analog value will be displayed on monitor window.
<br>[[File:ks0246 Result.gif|500px|frameless|thumb]]<br>
<br>[[File:ks0397 16-1.png|500px|frameless|thumb]]<br>
<br>[[File:ks0397 16-2.png|500px|frameless|thumb]]<br>
 
<br>
==Extension Experiment==
<br>
<span style=color:brown><big>'''Adding LCD Display'''</big></span><br>
<br>
'''Hookup Guide'''<br>
Connect the EASY Plug steam sensor and LCD module to control board using RJ11 cables.
<br>[[File:KS0246---0.png|500px|frameless|thumb]]<br>


<br>
<br>
'''Test Code'''<br>
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<br>[[File:ks0397 16.2.png|500px|frameless|thumb]]<br>
<br>
'''What You Should See'''<br>
<br>[[File:ks0397 16-3.png|500px|frameless|thumb]]<br>
Upload the code successfully, if the sensor detects a drop of water, the data will be showed on the LCD screen.
<br>[[File:ks0397 16-4.png|500px|frameless|thumb]]<br>
<br>
<span style="color: red">'''Little Knowledge:'''</span> <br>
* Remember you can adjust the contrast by rotating a blue potentiometer on the LCD back if you can’t make out the words clearly.
<br>[[File:ks0397 14-6.png|500px|frameless|thumb]]<br>
<br>
<br>
==Resources ==
==Resources ==
'''PDF'''<br>
 
https://drive.google.com/open?id=1XnoZiAUFd7R9szdJAM8j47OxiaaaGnWy
https://fs.keyestudio.com/KS0246
 


<br>
<br>
==Buy from ==
==Buy from ==
'''Official Website'''<br>
*[https://www.keyestudio.com/keyestudio-easy-plug-steam-sensor-module-for-arduino-steam-p0075-p0075.html    '''Official Website''']
http://www.keyestudio.com/easy-plug-steam-sensor.html
 
*[https://www.aliexpress.com/store/product/Keyestudio-EASY-plug-Steam-Sensor-module-for-arduino/1452162_32820572238.html?spm=2114.12010612.8148356.47.528d24eaRHbAow    Shop on aliexpress ]




[[Category:EASY Plug]]
[[Category:EASY Plug]]

Latest revision as of 08:42, 8 January 2021

Keyestudio EASY plug Steam Sensor

Introduction

Keyestudio steam sensor is an analog sensor and can make a simple rainwater detector and liquid level switch. When humidity on the surface of the sensor goes up, the output voltage will increase.
Warning: The connector is not waterproof, please be careful not to put the connector directly in water.
The module can be connected to the analog input interface with only one line, which is very easy and convenient.


Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.

Features

  • Connector: Easy plug
  • Working Voltage: 5V
  • Working Current: <20mA
  • Working Temperature: －10℃～＋70℃
  • Interface Type: Analog Signal Output


Technical Details

  • Dimensions: 35mm*24mm*18mm
  • Weight: 4.6g


Connect It Up

Connect the EASY Plug steam sensor to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See

When detect the different degree of humidity, the sensor outputs different value. If the sensor’s sensing area detects a water drop, the analog value will be displayed on monitor window.
thumb

thumb


Extension Experiment


Adding LCD Display

Hookup Guide
Connect the EASY Plug steam sensor and LCD module to control board using RJ11 cables.
thumb


Test Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See

thumb
Upload the code successfully, if the sensor detects a drop of water, the data will be showed on the LCD screen.
thumb


Little Knowledge:

  • Remember you can adjust the contrast by rotating a blue potentiometer on the LCD back if you can’t make out the words clearly.


thumb



Resources

https://fs.keyestudio.com/KS0246



Buy from

Retrieved from "http://wiki.keyestudio.com/index.php?title=Ks0246_keyestudio_EASY_plug_Steam_Sensor&oldid=30684"