Ks0266 keyestudio Eight-channel Solid State Relay Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(One intermediate revision by the same user not shown)
Line 84: Line 84:
|}
|}


* Output port: AC240V/2A
* Output port: AC 100V/2A


<br>
<br>
==Connection Diagram ==
==Connection Diagram ==
<br>[[File:KS0266(3).png|800px|frameless|thumb]]<br>
<br>[[File:KS0266(3).png|800px|frameless|thumb]]<br>
Line 124: Line 125:
<br>
<br>
==Resource ==
==Resource ==
* '''PDF:''' <br>
https://drive.google.com/open?id=1bVGkOans_UoWegSrJs8Ft3D4GEKakp-1


* '''Code:''' <br>
* '''Code:''' <br>
https://drive.google.com/open?id=1tOdLplPqGoc6RrVa1OffPwOZtjCF9Axl
https://fs.keyestudio.com/KS0266




<br>
<br>
==Buy from ==
==Buy from ==



Latest revision as of 10:21, 8 January 2021


Keyestudio Eight-channel Solid State Relay Module


thumb


Introduction

Keyestudio eight-channel solid state relay is active at HIGH level, that is to say, the input control signal is the high level (3.3-5 V), the relay is on; while the input control signal is low level (0-2.5 V), the relay is off.

Solid State Relay is a new kind of contactless switching device, which is composed of all solid state electronic components.

Compared with the electromagnetic relay, it has higher reliability, with the features of non-contact, long service life, fast speed and less outside interference.
The output control terminal of keyestudio solid-state relay must be connected to the circuit, can only be AC (Alternating Current) , so that the solid state relay can be disconnected normally.


thumb


Performance Parameters

  • Electrical parameters:
Voltage Static Current Working Current Trigger Voltage Trigger Current
Channel 1 DC 5V 0mA 13.8mA 3.3-5V 2mA
Channel 2 DC 5V 0mA 26.8mA 3.3-5V 2mA
Channel 3 DC 5V 0mA 37mA 3.3-5V 2mA
Channel 4 DC 5V 0mA 48mA 3.3-5V 2mA
Channel 5 DC 5V 0mA 59mA 3.3-5V 2mA
Channel 6 DC 5V 0mA 70mA 3.3-5V 2mA
Channel 7 DC 5V 0mA 81mA 3.3-5V 2mA
Channel 8 DC 5V 0mA 90mA 3.3-5V 2mA
  • Output port: AC 100V/2A


Connection Diagram


thumb


Sample Code

int BASE = 3 ;  //The first relay I/O port
int NUM = 8 ;  //Total number of relay
void setup()
{
   for (int i = BASE; i < BASE + NUM; i ++) 
   {
     pinMode(i, OUTPUT);   //Set the digital I/O port to output
   }
}

void loop()
{
   for (int i = BASE; i < BASE + NUM; i ++) 
   {
     digitalWrite(i, HIGH);    //Set the digital I/O port outputs to "HIGH", that is, gradually open relay
     delay(200);        //delay
   }
   for (int i = BASE; i < BASE + NUM; i ++) 
   {
     digitalWrite(i, LOW);    //Set the digital I/O port outputs to "LOW", that is, gradually close relay
     delay(200);        //delay
   }  
}


Result

Wiring as the above image, after powered-on, eight-channel solid state relays are first connected and then broken successively,repeating alternately.


Resource

  • Code:

https://fs.keyestudio.com/KS0266



Buy from