Ks0202 keyestudio Balance Car Shield

keyestudio Balance Car Shield

Introduction

keyestudio Balance Car Shield is developed by keyestudio based on Arduino development board. It is mainly used in balance car. We equip it with a driver chip called L298P which is applied to large power motors produced by LGS company. So the shield can drive two DC motors, whose current reach to 2A. It also has MPU6050 chip coming with DMP which process data and output through IIC.

Features

1. Working Voltage: DC 12V

2. Working Current in driver: ≤ 2 A

3. Working Temperature: 0℃ to 80℃

4. Coming with xbee/Bluetooh Bee wireless interface

5. On-board buzzer(D6) used as alarming

6. D11 as PWM pin 1 of motor 1, D9 as PWM pin 2 of motor 2, D 10 and D12 as output pin of motor 1, D8 and D7 as output pin of motor 2

7. With two PH2.0-6P motor interfaces

Connection Diagram

Stack it onto the board

Sample Code

Get the libraries of Wire: [1]
Get the libraries of MPU6050： [2]
Get the Code: [3]
Or you can directly copy the code as below:

/*
    MPU6050 Triple Axis Gyroscope & Accelerometer. Free fall detection.
    Read more: http://www.jarzebski.pl/arduino/czujniki-i-sensory/3-osiowy-zyroskop-i-akcelerometr-mpu6050.html
    GIT: https://github.com/jarzebski/Arduino-MPU6050
    Web: http://www.jarzebski.pl
    (c) 2014 by Korneliusz Jarzebski
*/

#include <Wire.h>
#include <MPU6050.h>

MPU6050 mpu;

boolean ledState = false;
boolean freefallDetected = false;
int freefallBlinkCount = 0;

void setup() 
{
  Serial.begin(115200);

  Serial.println("Initialize MPU6050");

  while(!mpu.begin(MPU6050_SCALE_2000DPS, MPU6050_RANGE_16G))
  {
    Serial.println("Could not find a valid MPU6050 sensor, check wiring!");
    delay(500);
  }

  mpu.setAccelPowerOnDelay(MPU6050_DELAY_3MS);
  
  mpu.setIntFreeFallEnabled(true);
  mpu.setIntZeroMotionEnabled(false);
  mpu.setIntMotionEnabled(false);
  
  mpu.setDHPFMode(MPU6050_DHPF_5HZ);

  mpu.setFreeFallDetectionThreshold(17);
  mpu.setFreeFallDetectionDuration(2);	
  
  checkSettings();

  pinMode(4, OUTPUT);
  digitalWrite(4, LOW);
  
  attachInterrupt(0, doInt, RISING);
}

void doInt()
{
  freefallBlinkCount = 0;
  freefallDetected = true;  
}

void checkSettings()
{
  Serial.println();
  
  Serial.print(" * Sleep Mode:                ");
  Serial.println(mpu.getSleepEnabled() ? "Enabled" : "Disabled");

  Serial.print(" * Motion Interrupt:     ");
  Serial.println(mpu.getIntMotionEnabled() ? "Enabled" : "Disabled");

  Serial.print(" * Zero Motion Interrupt:     ");
  Serial.println(mpu.getIntZeroMotionEnabled() ? "Enabled" : "Disabled");

  Serial.print(" * Free Fall Interrupt:       ");
  Serial.println(mpu.getIntFreeFallEnabled() ? "Enabled" : "Disabled");

  Serial.print(" * Free Fal Threshold:          ");
  Serial.println(mpu.getFreeFallDetectionThreshold());

  Serial.print(" * Free FallDuration:           ");
  Serial.println(mpu.getFreeFallDetectionDuration());
  
  Serial.print(" * Clock Source:              ");
  switch(mpu.getClockSource())
  {
    case MPU6050_CLOCK_KEEP_RESET:     Serial.println("Stops the clock and keeps the timing generator in reset"); break;
    case MPU6050_CLOCK_EXTERNAL_19MHZ: Serial.println("PLL with external 19.2MHz reference"); break;
    case MPU6050_CLOCK_EXTERNAL_32KHZ: Serial.println("PLL with external 32.768kHz reference"); break;
    case MPU6050_CLOCK_PLL_ZGYRO:      Serial.println("PLL with Z axis gyroscope reference"); break;
    case MPU6050_CLOCK_PLL_YGYRO:      Serial.println("PLL with Y axis gyroscope reference"); break;
    case MPU6050_CLOCK_PLL_XGYRO:      Serial.println("PLL with X axis gyroscope reference"); break;
    case MPU6050_CLOCK_INTERNAL_8MHZ:  Serial.println("Internal 8MHz oscillator"); break;
  }
  
  Serial.print(" * Accelerometer:             ");
  switch(mpu.getRange())
  {
    case MPU6050_RANGE_16G:            Serial.println("+/- 16 g"); break;
    case MPU6050_RANGE_8G:             Serial.println("+/- 8 g"); break;
    case MPU6050_RANGE_4G:             Serial.println("+/- 4 g"); break;
    case MPU6050_RANGE_2G:             Serial.println("+/- 2 g"); break;
  }  

  Serial.print(" * Accelerometer offsets:     ");
  Serial.print(mpu.getAccelOffsetX());
  Serial.print(" / ");
  Serial.print(mpu.getAccelOffsetY());
  Serial.print(" / ");
  Serial.println(mpu.getAccelOffsetZ());

  Serial.print(" * Accelerometer power delay: ");
  switch(mpu.getAccelPowerOnDelay())
  {
    case MPU6050_DELAY_3MS:            Serial.println("3ms"); break;
    case MPU6050_DELAY_2MS:            Serial.println("2ms"); break;
    case MPU6050_DELAY_1MS:            Serial.println("1ms"); break;
    case MPU6050_NO_DELAY:             Serial.println("0ms"); break;
  }  
  
  Serial.println();
}

void loop()
{
  Vector rawAccel = mpu.readRawAccel();
  Activites act = mpu.readActivites();

  Serial.print(act.isFreeFall);
  Serial.print("\n");
  
  if (freefallDetected)
  {
    ledState = !ledState;

    digitalWrite(4, ledState);

    freefallBlinkCount++;

    if (freefallBlinkCount == 20)
    {
      freefallDetected = false;
      ledState = false;
      digitalWrite(4, ledState);
    }
  }
  
  delay(100);
  
}

Documents

PDF:

https://drive.google.com/open?id=13AiPQpHPVIGNGdiq7w6BMvr6-JXFRli5

Download the Libraries of MPU6050:

https://drive.google.com/open?id=1hhzfuT0svXpU9bf1Q22QpEhEfaGkPa6Z

Download the Libraries of Wire:

https://drive.google.com/open?id=10e6rKkKaSpV_Thoe7dz2ZqoOp_XvPEM-

Download the Code:

https://drive.google.com/open?id=19ImbFnkGphDNZZt50xMLbZC7dsb-g3oH

Buy From

http://www.keyestudio.com/keyestudio-balance-car-shield.html