Ks0159 keyestudio Desktop Bluetooth Mini Smart Car: Difference between revisions
Keyestudio (talk | contribs) |
Keyestudio (talk | contribs) |
||
(45 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
==keyestudio Desktop Bluetooth Mini Smart Car== | ==keyestudio Desktop Bluetooth Mini Smart Car== | ||
<br>[[File:KS0159.png|500px|frameless|thumb]]<br> | |||
==Introduction== | |||
Multi-functional smart car is a learning application development system of microcontroller that can be controlled by ARDUINO. It has functions of line tracking, obstacle avoidance, Bluetooth remote control etc. This kit contains many interesting programs. It can also be expanded to have external circuit modules to have other functions. This kit is designed to help you to learn Arduino programming in an interesting way. You can learn Arduino MCU development ability while having fun. | |||
==Introduction== | |||
Multi-functional smart car is a learning application development system of microcontroller that can be controlled by ARDUINO. It has functions of line tracking, obstacle avoidance, Bluetooth remote control etc. This kit contains many interesting programs. It can also be expanded to have external circuit modules to have other functions. This kit is designed to help you | |||
==Parameters== | ==Parameters== | ||
Line 16: | Line 14: | ||
==Standard Component List== | ==Standard Component List== | ||
1. N20 metal gear motor * 4<br> | 1. N20 metal gear motor * 4<br> | ||
2. High quality | 2. High quality wheel* 4<br> | ||
3. Motor holder *4 <br> | 3. Motor holder *4 <br> | ||
4. Car chassis * 2<br> | 4. Car chassis * 2 <br> | ||
5. L298P motor driver shield * 1 <br> | 5. L298P motor driver shield * 1 <br> | ||
6. ARDUINO UNO328 board * 1 <br> | 6. ARDUINO UNO328 board * 1 <br> | ||
Line 28: | Line 25: | ||
10. HC-06 Bluetooth module * 1<br> | 10. HC-06 Bluetooth module * 1<br> | ||
11. 14500 battery pack * 1 <br> | 11. 14500 battery pack * 1 <br> | ||
12. 3PIN Dupont wires * 6<br> | 12. 3PIN Dupont wires * 6 <br> | ||
13. 27MM Copper bush * 4<br> | 13. 27MM Copper bush * 4 <br> | ||
14. 10MM Copper bush * 2<br> | 14. 10MM Copper bush * 2 <br> | ||
15. 3MM screws and nuts * several<br> | 15. 3MM screws and nuts * several <br> | ||
'''Self-prepare parts:'''<br> | |||
3.7V large capacity 1300mA imported 14500 rechargeable batteries *2<br> | *3.7V large capacity 1300mA imported 14500 rechargeable batteries *2 <br> | ||
14500 charger *1<br> | *14500 charger *1 <br> | ||
==Installation instructions== | ==Installation instructions== | ||
Line 99: | Line 97: | ||
==Application of Arduino== | ==Application of Arduino== | ||
<br>[[File:UNO R3--.png|500px|frameless|thumb]]<br> | |||
<br> | |||
'''Introduction''' <br> | |||
'''Introduction''' | <br> | ||
What’s Arduino?<br> | '''What’s an Arduino?''' <br> | ||
Arduino is an open-source hardware project platform. This platform includes a circuit board with simple I/O function and program development environment software. It can be used to develop interactive products. For example, it can read signals of multiple switches and sensors, and control light, servo motor and other various physical devices. It’s widely applied in robot field.<br> | Arduino is an open-source hardware project platform. This platform includes a circuit board with simple I/O function and program development environment software. It can be used to develop interactive products. For example, it can read signals of multiple switches and sensors, and control light, servo motor and other various physical devices. It’s widely applied in robot field.<br> | ||
<br> | |||
'''Arduino installation and program upload:'''<br> | '''Arduino installation and program upload:'''<br> | ||
First, download the Arduino development software, click below hyperlink: <br> | First, download the Arduino development software, click below hyperlink: <br> | ||
[http://183.131.116.28/7326097.s21d-7.faiusrd.com/0/ABUIABAAGAAgx72stAUomOnzwAQ?f=arduino-1.5.6-r2-windows.rar&v=1451957958&wsiphost=local arduino-1.5.6-r2-windows.rar]<br> | [http://183.131.116.28/7326097.s21d-7.faiusrd.com/0/ABUIABAAGAAgx72stAUomOnzwAQ?f=arduino-1.5.6-r2-windows.rar&v=1451957958&wsiphost=local arduino-1.5.6-r2-windows.rar]<br> | ||
Downloaded file is a arduino-1.5.6-r2-windows.zip compressed folder, unzip it to your hard drive.<br> | Downloaded file is a arduino-1.5.6-r2-windows.zip compressed folder, unzip it to your hard drive.<br> | ||
Double click Arduino-1.5.6 .exe. Click “I agree”;<br> | Double click Arduino-1.5.6 .exe. Click “I agree”;<br> | ||
<br>[[File:15932.png|500px|frameless|thumb]]<br> | <br>[[File:15932.png|500px|frameless|thumb]]<br> | ||
Click “Next”; | Click “Next”; | ||
<br>[[File:15933.png|500px|frameless|thumb]]<br> | <br>[[File:15933.png|500px|frameless|thumb]]<br> | ||
And then “Install”; | And then “Install”; | ||
<br>[[File:15934.png|500px|frameless|thumb]]<br> | <br>[[File:15934.png|500px|frameless|thumb]]<br> | ||
Wait for the installation to be completed, click close. | Wait for the installation to be completed, click close. | ||
<br>[[File:15935.png|500px|frameless|thumb]]<br> | <br>[[File:15935.png|500px|frameless|thumb]]<br> | ||
Below | Below figure shows what Arduino 1.5.6 looks like. | ||
<br>[[File:15936.png|500px|frameless|thumb]]<br> | <br>[[File:15936.png|500px|frameless|thumb]]<br> | ||
<br> | |||
'''Next, let’s install Arduino driver.''' <br> | '''Next, let’s install Arduino driver.''' <br> | ||
For different operating system, there may be slight difference in installation method. Below is an example in WIN 7.<br> | For different operating system, there may be slight difference in installation method. Below is an example in WIN 7.<br> | ||
When you connect Arduino Uno to your computer the first time, right click “Computer” —> “Properties”—> “Device manager”, you can see “Unknown devices”. | When you connect Arduino Uno to your computer at the first time, right click “Computer” —> “Properties”—> “Device manager”, you can see “Unknown devices”. | ||
<br>[[File:15937.png|500px|frameless|thumb]]<br> | <br>[[File:15937.png|500px|frameless|thumb]]<br> | ||
Click “Unknown devices”, select “Update Driver software”. | Click “Unknown devices”, select “Update Driver software”. | ||
<br>[[File:15938.png|500px|frameless|thumb]]<br> | <br>[[File:15938.png|500px|frameless|thumb]]<br> | ||
In this page, click “Browse my computer for driver software”. | In this page, click “Browse my computer for driver software”. | ||
<br>[[File:15939.png|500px|frameless|thumb]]<br> | <br>[[File:15939.png|500px|frameless|thumb]]<br> | ||
Find the “drivers” file. | Find the “drivers” file. | ||
<br>[[File:15940.png|500px|frameless|thumb]]<br> | <br>[[File:15940.png|500px|frameless|thumb]]<br> | ||
Click “Next”; select “Install this driver software anyway” to begin the installation. | Click “Next”; select “Install this driver software anyway” to begin the installation. | ||
<br>[[File:15941.png|500px|frameless|thumb]]<br> | <br>[[File:15941.png|500px|frameless|thumb]]<br> | ||
Installation completed; click “Close”. | Installation completed; click “Close”. | ||
<br>[[File:15942.png|500px|frameless|thumb]]<br> | <br>[[File:15942.png|500px|frameless|thumb]]<br> | ||
<br> | |||
After driver is installed, go to “Device manager” again. Right click “Computer” —> “Properties”—> “Device manager”, you can see UNO device as below figure shows, also the Com port info. | After driver is installed, go to “Device manager” again. Right click “Computer” —> “Properties”—> “Device manager”, you can see UNO device as below figure shows, also the Com port info. | ||
<br>[[File:15943.png|500px|frameless|thumb]]<br> | <br>[[File:15943.png|500px|frameless|thumb]]<br> | ||
<br> | |||
Following is a sketch uploading example called “Hello World!”. <br> | Following is a sketch uploading example called “Hello World!”. <br> | ||
First, open Arduino IDE. In this example sketch, we program Arduino to display “Hello World!” | Copy and paste the code to the Arduino environment IDE. | ||
<pre> | |||
int val; | |||
int ledpin=13; | |||
void setup() | |||
{ | |||
Serial.begin(9600); | |||
pinMode(ledpin,OUTPUT); | |||
} | |||
void loop() | |||
{ | |||
val=Serial.read(); | |||
if(val=='R') | |||
{ | |||
digitalWrite(ledpin,HIGH); | |||
delay(500); | |||
digitalWrite(ledpin,LOW); | |||
delay(500); | |||
Serial.println("Hello World!"); | |||
} | |||
} | |||
</pre> | |||
First, open Arduino IDE. In this example sketch, we program Arduino to display “Hello World!” on serial monitor when it receives a specific character string “R”; also the on-board D13 LED will blink once each time it receives “R”.<br> | |||
First, set up board; In “Tools”, select “Arduino Uno”. <br> | First, set up board; In “Tools”, select “Arduino Uno”. <br> | ||
Line 179: | Line 192: | ||
After uploading is done, open “serial monitor [[File:15950.png|500px|frameless|thumb]]”; enter “R”; click “Send”, the serial monitor will display “Hello World!” and the D13 LED will blink once. | After uploading is done, open “serial monitor [[File:15950.png|500px|frameless|thumb]]”; enter “R”; click “Send”, the serial monitor will display “Hello World!” and the D13 LED will blink once. | ||
<br>[[File:15951.png|500px|frameless|thumb]]<br> | <br>[[File:15951.png|500px|frameless|thumb]]<br> | ||
<br> | |||
Congratulations! Your first sketch uploading is successful! | |||
<br> | |||
==Project details== | ==Project details== | ||
Line 188: | Line 202: | ||
===Project 1: Line-tracking smart car=== | ===Project 1: Line-tracking smart car=== | ||
'''Introduction''' | '''Introduction''' <br> | ||
This project is a simple line-tracking smart car system based on Arduino. The controller part is a UNO board. An infrared photoelectric sensor is used to detect black line, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically move towards a black line. | This project is a simple line-tracking smart car system based on Arduino. The controller part is a UNO board. An infrared photoelectric sensor is used to detect black line, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically move towards a black line. | ||
'''Working principle''' | <br> | ||
'''Working principle'''<br> | |||
1. For color black, it has characteristic of low reflectivity to light. When the surface color is not black, most of the red light the sensor sends will be reflected. The sensor outputs low level signal 0.<br> | 1. For color black, it has characteristic of low reflectivity to light. When the surface color is not black, most of the red light the sensor sends will be reflected. The sensor outputs low level signal 0.<br> | ||
2. If there is black line on a surface, when the sensor is above it, color black has low reflectivity; reflected infrared light is not enough to reach the sensor’s action level, so the sensor output is still l. <br> | 2. If there is black line on a surface, when the sensor is above it, color black has low reflectivity; reflected infrared light is not enough to reach the sensor’s action level, so the sensor output is still l. <br> | ||
Line 199: | Line 212: | ||
4. The MCU will control the car moving action according to the signal received.<br> | 4. The MCU will control the car moving action according to the signal received.<br> | ||
'''Main hardware introduction''' | <br> | ||
'''Main hardware introduction''' <br> | |||
<br>[[File: | <br>[[File:Line tracking sensor.png|500px|frameless|thumb]]<br> | ||
<br> | |||
In the line tracking sensor, TCRT5000 infrared tubes are applied. The working principle is based on the infrared's different reflectivity of different color. The strength of the reflected signal is then converted into current signal. For this line tracking module, it's high level signal when detecting black line, low level when detecting white line. Detection height is 0-3cm.<br> | In the line tracking sensor, TCRT5000 infrared tubes are applied. The working principle is based on the infrared's different reflectivity of different color. The strength of the reflected signal is then converted into current signal. For this line tracking module, it's high level signal when detecting black line, low level when detecting white line. Detection height is 0-3cm.<br> | ||
Note: you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module. | '''Note:''' you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module. | ||
'''Performance parameter:''' | <br> | ||
'''Performance parameter:'''<br> | |||
1. Detection height: 3cm when detecting black line on white background; the detection height varies with background color; highest in white background. <br> | 1. Detection height: 3cm when detecting black line on white background; the detection height varies with background color; highest in white background. <br> | ||
2. Power supply voltage: 2.5V to 12V, no more than 12V. (Note: it is better to use low voltage power supply, high power supply voltage will shorten service life of the sensor. 5V power supply is preferred.)<br> | 2. Power supply voltage: 2.5V to 12V, no more than 12V. (Note: it is better to use low voltage power supply, high power supply voltage will shorten service life of the sensor. 5V power supply is preferred.)<br> | ||
Line 214: | Line 227: | ||
5. The sensor outputs TTL level signal; can be directly connected to the IO port of 3.3V or 5V MCU.<br> | 5. The sensor outputs TTL level signal; can be directly connected to the IO port of 3.3V or 5V MCU.<br> | ||
'''Usage:''' | <br> | ||
'''Usage:'''<br> | |||
1. The sensor has 3 pins, namely G, +V and S. G and +V are for power supply. S is signal output pin.<br> | 1. The sensor has 3 pins, namely G, +V and S. G and +V are for power supply. S is signal output pin.<br> | ||
2. When it detects black line, the signal end outputs high level signal 1; when no black line detected, the signal end outputs low level 0.<br> | 2. When it detects black line, the signal end outputs high level signal 1; when no black line detected, the signal end outputs low level 0.<br> | ||
3. From the output 0 or 1, the sensor can determine whether the color is black or not. <br> | 3. From the output 0 or 1, the sensor can determine whether the color is black or not. <br> | ||
'''Module test program:''' | <br> | ||
'''Module test program:'''<br> | |||
<pre> | <pre> | ||
///Arduino Sample Code | ///Arduino Sample Code | ||
Line 234: | Line 247: | ||
} | } | ||
</pre> | </pre> | ||
<br> | |||
'''Schematic and connection diagram''' | '''Schematic and connection diagram''' | ||
<br>[[File:KS0159-1循线原理.jpg|600px|frameless|thumb]]<br> | |||
<br>[[File:KS0159-1循线.jpg|600px|frameless|thumb]]<br> | |||
<br> | <br> | ||
'''Line tracking car program'''<br> | |||
'''Line tracking car program''' | |||
<pre> | <pre> | ||
#define SensorLeft 4 // left sensor input pin | #define SensorLeft 4 // left sensor input pin | ||
Line 323: | Line 334: | ||
} | } | ||
</pre> | </pre> | ||
<br> | |||
When the car enters line tracking mode, it begins constantly scanning I/O port of the MCU that connects the detecting sensor. When it picks up a signal of the I/O port , it will enter the judgment processing; firstly determine which sensor detects the black line. | When the car enters line tracking mode, it begins constantly scanning I/O port of the MCU that connects the detecting sensor. When it picks up a signal of the I/O port , it will enter the judgment processing; firstly determine which sensor detects the black line. | ||
<br> | |||
<br> | |||
===Project 2: Obstacle-avoidance smart car=== | ===Project 2: Obstacle-avoidance smart car=== | ||
<br> | |||
'''Introduction''' | '''Introduction''' <br> | ||
This project is a simple obstacle avoidance smart car system based on Arduino. The controller part is a UNO board. An obstacle avoidance sensor is used to detect whether there is obstacle ahead, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically avoid obstacles. | This project is a simple obstacle avoidance smart car system based on Arduino. The controller part is a UNO board. An obstacle avoidance sensor is used to detect whether there is obstacle ahead, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically avoid obstacles. | ||
'''Working principle''' | <br> | ||
'''Working principle'''<br> | |||
1. Obstacle avoidance sensor is applied here. The sensor has a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal. <br> | 1. Obstacle avoidance sensor is applied here. The sensor has a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal. <br> | ||
2. When it detects an obstacle ahead, the sensor will output low level 0; when there is no obstacle detected, the sensor outputs high level signal 1. <br> | 2. When it detects an obstacle ahead, the sensor will output low level 0; when there is no obstacle detected, the sensor outputs high level signal 1. <br> | ||
Line 339: | Line 350: | ||
4. The MCU will control the car moving action according to the signal received.<br> | 4. The MCU will control the car moving action according to the signal received.<br> | ||
'''Main hardware introduction''' | <br> | ||
'''Main hardware introduction'''<br> | |||
<br>[[File: | <br>[[File:Obstacle sensor.png|500px|frameless|thumb]]<br> | ||
Infrared obstacle avoidance sensor is equipped with a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1. | Infrared obstacle avoidance sensor is equipped with a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1. | ||
Note: you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module. | '''Note:''' you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module. | ||
'''Performance parameter:''' | <br> | ||
'''Performance parameter:''' <br> | |||
1. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1. The sensor can be directly connected to the IO port of 3.3V or 5V MCU. <br> | 1. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1. The sensor can be directly connected to the IO port of 3.3V or 5V MCU. <br> | ||
2. Detection distance is 2-40cm, long distance and high precision. (Note: for infrared sensor, the detection distance varies with difference in object color because different color has different reflectivity of light, the darker the object, the shorter the detection distance. The distance 2-40cm is calculated when the sensor is facing a white wall.)<br> | 2. Detection distance is 2-40cm, long distance and high precision. (Note: for infrared sensor, the detection distance varies with difference in object color because different color has different reflectivity of light, the darker the object, the shorter the detection distance. The distance 2-40cm is calculated when the sensor is facing a white wall.)<br> | ||
Line 354: | Line 365: | ||
4. Wide power supply range of 3-6V, suitable for using with 3.3-5V micro-controller.<br> | 4. Wide power supply range of 3-6V, suitable for using with 3.3-5V micro-controller.<br> | ||
5. Equipped with EN pin, when this pin output is “1”, the sensor is not operating; when the output is “0”, the sensor is. When the wire jumper on the module is put on, the EN pin is connected to GND and the output is “0”. If you want to use the EN pin, just take away the wire jumper.<br> | 5. Equipped with EN pin, when this pin output is “1”, the sensor is not operating; when the output is “0”, the sensor is. When the wire jumper on the module is put on, the EN pin is connected to GND and the output is “0”. If you want to use the EN pin, just take away the wire jumper.<br> | ||
6. Frequency adjusting potentiometer is used to adjust the carrier frequency of the infrared transmitting tube, because the integrated receiver is the most sensitive when in 38 KHZ carrier frequency. Adjust the 502 pot's clockwise to the upmost (that is when the transmitting tube is the brightest); then face the sensor to a white wall and adjust the 103 pot's until the detection distance is the furthest. Now the sensor is working at its best state. | 6. Frequency adjusting potentiometer is used to adjust the carrier frequency of the infrared transmitting tube, because the integrated receiver is the most sensitive when in 38 KHZ carrier frequency. Adjust the 502 pot's clockwise to the upmost (that is when the transmitting tube is the brightest); then face the sensor to a white wall and adjust the 103 pot's until the detection distance is the furthest. Now the sensor is working at its best state.<br> | ||
'''Usage:''' | <br> | ||
1. The sensor has 4 pins, namely GND, +, OUT, and EN. + and GND is for power supply; OUT is signal output pin. When in actual use, you only need to +, GND and OUT. | '''Usage:''' <br> | ||
2. When an obstacle is detected, the signal pin outputs low level signal 0, when no obstacle detected, signal end outputs high level signal 1. | 1. The sensor has 4 pins, namely GND, +, OUT, and EN. + and GND is for power supply; OUT is signal output pin. When in actual use, you only need to +, GND and OUT. <br> | ||
3. By determining whether the sensor output is 0 or 1, it can determine whether there is an obstacle ahead. | 2. When an obstacle is detected, the signal pin outputs low level signal 0, when no obstacle detected, signal end outputs high level signal 1. <br> | ||
3. By determining whether the sensor output is 0 or 1, it can determine whether there is an obstacle ahead. <br> | |||
<br> | |||
'''Module test program:'''<br> | |||
<pre> | <pre> | ||
const int sensorPin = 2; // the number of the sensor pin | const int sensorPin = 2; // the number of the sensor pin | ||
Line 382: | Line 394: | ||
</pre> | </pre> | ||
'''Schematic and connection diagram''' | <br> | ||
'''Schematic and connection diagram'''<br> | |||
<br>[[File: | <br>[[File:KS0159-2避障原理.jpg|600px|frameless|thumb]]<br> | ||
<br>[[File:KS0159-2避障.jpg|600px|frameless|thumb]]<br> | |||
<br>[[File: | |||
<br> | |||
'''Obstacle avoidance car program'''<br> | |||
<pre> | <pre> | ||
#define IRSensorLeft 10 // left sensor input pin | #define IRSensorLeft 10 // left sensor input pin | ||
Line 472: | Line 483: | ||
</pre> | </pre> | ||
<br> | |||
===Project 3: Bluetooth smart car=== | ===Project 3: Bluetooth smart car=== | ||
'''Introduction''' | '''Introduction''' <br> | ||
This project is a smart car system based on Bluetooth communication, including software and hardware design. The controller part is a UNO board. A Bluetooth module is used to receive the Bluetooth signal from the cellphone and pass on to the UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can be controlled by cellphone. | This project is a smart car system based on Bluetooth communication, including software and hardware design. The controller part is a UNO board. A Bluetooth module is used to receive the Bluetooth signal from the cellphone and pass on to the UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can be controlled by cellphone. | ||
'''Working principle''' | <br> | ||
'''Working principle'''<br> | |||
1. The UNO is connected to a Bluetooth module; the module communicates with cell phone through a Bluetooth APP. <br> | 1. The UNO is connected to a Bluetooth module; the module communicates with cell phone through a Bluetooth APP. <br> | ||
2. The Bluetooth APP on the cell phone will pass information of “U”“D”“L”“R”“S” to the Bluetooth module. <br> | 2. The Bluetooth APP on the cell phone will pass information of “U”“D”“L”“R”“S” to the Bluetooth module. <br> | ||
Line 485: | Line 496: | ||
4. When the UNO receives a “U”, the car goes straight forward; when it receives a “D”, the car goes backward; “L” for turning left; “R” for turning right; and “S” for stop. | 4. When the UNO receives a “U”, the car goes straight forward; when it receives a “D”, the car goes backward; “L” for turning left; “R” for turning right; and “S” for stop. | ||
'''Main hardware introduction''' | <br> | ||
'''Main hardware introduction''' <br> | |||
<br>[[File: | <br>[[File:Bluetooth module.png|500px|frameless|thumb]]<br> | ||
<br> | |||
'''Bluetooth communication:'''<br> | |||
The term “Bluetooth” is derived from a Denmark king’s name in 10th century. The king is named Harald Blatand, while “Blatand” in English means Bluetooth. | The term “Bluetooth” is derived from a Denmark king’s name in 10th century. The king is named Harald Blatand, while “Blatand” in English means Bluetooth. | ||
The so-called bluetooth technology is actually a type of short distance wireless transmission technology. We can use “Bluetooth” to effectively simplify the communication between terminal devices such as laptop and mobile phone. It can also simplify communication between these devices and the Internet, thus improving the speed and efficiency of data transmission between them, widening the application scope of wireless communication. | The so-called bluetooth technology is actually a type of short distance wireless transmission technology. We can use “Bluetooth” to effectively simplify the communication between terminal devices such as laptop and mobile phone. It can also simplify communication between these devices and the Internet, thus improving the speed and efficiency of data transmission between them, widening the application scope of wireless communication. | ||
'''Performance parameter:''' | <br> | ||
'''Performance parameter:''' <br> | |||
1. The Bluetooth module used here is a HC-06 slave module. It has 4 pins namely VCC, GND, TXD and RXD.<br> | 1. The Bluetooth module used here is a HC-06 slave module. It has 4 pins namely VCC, GND, TXD and RXD.<br> | ||
2. With an LED indicator to indicate connection status, quick flashing means no Bluetooth connected; steadily on means Bluetooth is connected and the channel is open.<br> | 2. With an LED indicator to indicate connection status, quick flashing means no Bluetooth connected; steadily on means Bluetooth is connected and the channel is open.<br> | ||
Line 506: | Line 517: | ||
9. Module size: 40mm*15mm<br> | 9. Module size: 40mm*15mm<br> | ||
'''Usage: ''' | <br> | ||
'''Usage: '''<br> | |||
1. The sensor has 4 pins, GND, VCC, RX and TX. Connect main board +5V to Bluetooth VCC, main board GND to Bluetooth GND, main board TX to Bluetooth RX and RX to Bluetooth TX. <br> | 1. The sensor has 4 pins, GND, VCC, RX and TX. Connect main board +5V to Bluetooth VCC, main board GND to Bluetooth GND, main board TX to Bluetooth RX and RX to Bluetooth TX. <br> | ||
2. Remember to open the Bluetooth on your phone; when you open the Bluetooth APP, it will remind you.<br> | 2. Remember to open the Bluetooth on your phone; when you open the Bluetooth APP, it will remind you.<br> | ||
Line 514: | Line 525: | ||
5. Open Bluetooth APP and pair up Bluetooth device. After it’s paired, the Bluetooth module can communicate with cell phone. <br> | 5. Open Bluetooth APP and pair up Bluetooth device. After it’s paired, the Bluetooth module can communicate with cell phone. <br> | ||
'''Module test:''' | <br> | ||
'''Module test:'''<br> | |||
Since this is your first try with Bluetooth module, we’ll do a simple test of having Arduino to successfully communicate with PC. First is the wire connection. Connect the module to the main board as stated in usage (refer to below figure). When the Bluetooth module is successfully connected to PC, the power indicator of the module will blink and connection indicator the green one will be on. | Since this is your first try with Bluetooth module, we’ll do a simple test of having Arduino to successfully communicate with PC. First is the wire connection. Connect the module to the main board as stated in usage (refer to below figure). When the Bluetooth module is successfully connected to PC, the power indicator of the module will blink and connection indicator the green one will be on. | ||
<br>[[File:Ks0055 蓝牙.jpg|500px|frameless|thumb]]<br> | |||
<br> | |||
Now, let’s move on to the program. I’ll enter “r” and after Arduino receives my command “r”, the pin13 LED on the main board will blink and serial monitor will print “keyes”. <br> | |||
Now, let’s move on to the program. I’ll enter “r” and after Arduino receives my command “r”, the pin13 LED on the main board will blink and serial monitor will print “keyes”. The program is as follows: | The program is as follows: | ||
<pre> | <pre> | ||
Line 534: | Line 547: | ||
if(val=='r') | if(val=='r') | ||
{ | { | ||
digitalWrite( | digitalWrite(ledpin,HIGH); | ||
delay | delay(500); | ||
digitalWrite( | digitalWrite(ledpin,LOW); | ||
delay(500); | delay(500); | ||
Serial.println("keyes"); | Serial.println("keyes"); | ||
Line 543: | Line 556: | ||
</pre> | </pre> | ||
<br> | |||
'''Schematic and connection diagram'''<br> | |||
<br>[[File:KS0159-3蓝牙原理.jpg|600px|frameless|thumb]]<br> | |||
<br>[[File:KS0159-3蓝牙.jpg|600px|frameless|thumb]]<br> | |||
<br> | |||
'''Bluetooth smart car program'''<br> | |||
'''Bluetooth smart car program''' | |||
Arduino Bluetooth remote control programmable smart car | Arduino Bluetooth remote control programmable smart car | ||
< | <pre> | ||
// | // | ||
#define E1 3 | #define E1 3 | ||
Line 620: | Line 631: | ||
if(val=='S')stopp(); | if(val=='S')stopp(); | ||
} | } | ||
</pre> | </pre> | ||
==Resources == | |||
Please access this following link to get more details: | |||
https://fs.keyestudio.com/KS0159 | |||
==Buy from == | |||
*[https://www.keyestudio.com/keyestudio-desktop-bluetooth-smart-robot-car-kit-for-arduino-robot-education-programming3projectsuser-manualpdfonline-p0049-p0049.html '''Official Website'''] | |||
*[https://www.aliexpress.com/store/product/2016-New-Keyestudio-Desktop-Wireless-Bluetooth-Mini-Smart-Car-Robot-car-DIY-Kit-for-Arduino-Kit/1452162_32654940547.html?spm=2114.12010612.8148356.17.410533d1YxHRkR '''Aliexpress store''' ] | |||
*[https://www.amazon.com/KEYESTUDIO-Arduino-Bluetooth-Tutorial-Education/dp/B01EY75RE8?ref_=w_bl_hsx_s_pc_web_13497667011 '''Amazon store'''] | |||
[[category:Smart Car]] | [[category:Smart Car]] |
Latest revision as of 10:55, 1 June 2020
keyestudio Desktop Bluetooth Mini Smart Car
Introduction
Multi-functional smart car is a learning application development system of microcontroller that can be controlled by ARDUINO. It has functions of line tracking, obstacle avoidance, Bluetooth remote control etc. This kit contains many interesting programs. It can also be expanded to have external circuit modules to have other functions. This kit is designed to help you to learn Arduino programming in an interesting way. You can learn Arduino MCU development ability while having fun.
Parameters
1. Motor parameters: Voltage: 1.5 -12V; shaft length: 10mm; Revolving speed: 6.0V 100rpm/min.
2. Use L298N driver module for motor control.
3. Three-channel line tracking modules, detecting black and white line, high precision, can also be used in fall prevention.
4. Three-channel infrared obstacle avoidance modules makes up the obstacle avoidance sensor, can detect whether there are obstacles ahead.
5. Equipped with Bluetooth wireless module, can remotely control the robot after pairing with mobile phone Bluetooth.
6. Can be connected to external 7 ~ 12V power supply; with various sensor modules, it can realize various functions.
Standard Component List
1. N20 metal gear motor * 4
2. High quality wheel* 4
3. Motor holder *4
4. Car chassis * 2
5. L298P motor driver shield * 1
6. ARDUINO UNO328 board * 1
7. ARDUINO sensor shield * 1
8. Infrared obstacle avoidance module *3
9. Line tracking module *3
10. HC-06 Bluetooth module * 1
11. 14500 battery pack * 1
12. 3PIN Dupont wires * 6
13. 27MM Copper bush * 4
14. 10MM Copper bush * 2
15. 3MM screws and nuts * several
Self-prepare parts:
- 3.7V large capacity 1300mA imported 14500 rechargeable batteries *2
- 14500 charger *1
Installation instructions
Application of Arduino
Introduction
What’s an Arduino?
Arduino is an open-source hardware project platform. This platform includes a circuit board with simple I/O function and program development environment software. It can be used to develop interactive products. For example, it can read signals of multiple switches and sensors, and control light, servo motor and other various physical devices. It’s widely applied in robot field.
Arduino installation and program upload:
First, download the Arduino development software, click below hyperlink:
arduino-1.5.6-r2-windows.rar
Downloaded file is a arduino-1.5.6-r2-windows.zip compressed folder, unzip it to your hard drive.
Double click Arduino-1.5.6 .exe. Click “I agree”;
Wait for the installation to be completed, click close.
Below figure shows what Arduino 1.5.6 looks like.
Next, let’s install Arduino driver.
For different operating system, there may be slight difference in installation method. Below is an example in WIN 7.
When you connect Arduino Uno to your computer at the first time, right click “Computer” —> “Properties”—> “Device manager”, you can see “Unknown devices”.
Click “Unknown devices”, select “Update Driver software”.
In this page, click “Browse my computer for driver software”.
Click “Next”; select “Install this driver software anyway” to begin the installation.
Installation completed; click “Close”.
After driver is installed, go to “Device manager” again. Right click “Computer” —> “Properties”—> “Device manager”, you can see UNO device as below figure shows, also the Com port info.
Following is a sketch uploading example called “Hello World!”.
Copy and paste the code to the Arduino environment IDE.
int val; int ledpin=13; void setup() { Serial.begin(9600); pinMode(ledpin,OUTPUT); } void loop() { val=Serial.read(); if(val=='R') { digitalWrite(ledpin,HIGH); delay(500); digitalWrite(ledpin,LOW); delay(500); Serial.println("Hello World!"); } }
First, open Arduino IDE. In this example sketch, we program Arduino to display “Hello World!” on serial monitor when it receives a specific character string “R”; also the on-board D13 LED will blink once each time it receives “R”.
First, set up board; In “Tools”, select “Arduino Uno”.
Next, set up COM port; In “Tools”, select “COM3”.
After selection, you can see indicated area is the same with settings in “Device manager”.
Copy the example sketch and paste it to the IDE; click “Verify ” to check compiling mistakes; click “Upload ” to upload the program to the board.
After uploading is done, open “serial monitor ”; enter “R”; click “Send”, the serial monitor will display “Hello World!” and the D13 LED will blink once.
Congratulations! Your first sketch uploading is successful!
Project details
Project 1: Line-tracking smart car
Introduction
This project is a simple line-tracking smart car system based on Arduino. The controller part is a UNO board. An infrared photoelectric sensor is used to detect black line, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically move towards a black line.
Working principle
1. For color black, it has characteristic of low reflectivity to light. When the surface color is not black, most of the red light the sensor sends will be reflected. The sensor outputs low level signal 0.
2. If there is black line on a surface, when the sensor is above it, color black has low reflectivity; reflected infrared light is not enough to reach the sensor’s action level, so the sensor output is still l.
3. To detect the black line, we only need a MCU to determine whether the sensor output is 0 or 1.
4. The MCU will control the car moving action according to the signal received.
Main hardware introduction
In the line tracking sensor, TCRT5000 infrared tubes are applied. The working principle is based on the infrared's different reflectivity of different color. The strength of the reflected signal is then converted into current signal. For this line tracking module, it's high level signal when detecting black line, low level when detecting white line. Detection height is 0-3cm.
Note: you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module.
Performance parameter:
1. Detection height: 3cm when detecting black line on white background; the detection height varies with background color; highest in white background.
2. Power supply voltage: 2.5V to 12V, no more than 12V. (Note: it is better to use low voltage power supply, high power supply voltage will shorten service life of the sensor. 5V power supply is preferred.)
3. Working current: 18~20ma under 5V power supply. After testing, when the working current is 18~20ma, the sensor is at its best performance in anti-jamming capability.
4. When it detects black line, the signal end outputs high level signal 1; when no black line detected, the signal end outputs low level 0.
5. The sensor outputs TTL level signal; can be directly connected to the IO port of 3.3V or 5V MCU.
Usage:
1. The sensor has 3 pins, namely G, +V and S. G and +V are for power supply. S is signal output pin.
2. When it detects black line, the signal end outputs high level signal 1; when no black line detected, the signal end outputs low level 0.
3. From the output 0 or 1, the sensor can determine whether the color is black or not.
Module test program:
///Arduino Sample Code void setup() { Serial.begin(9600); } void loop() { Serial.println(digitalRead(3)); // print the data from the sensor delay(500); }
Schematic and connection diagram
Line tracking car program
#define SensorLeft 4 // left sensor input pin #define SensorMiddle 5 // middle sensor input pin #define SensorRight 6 // right sensor input pin unsigned char SL; // left sensor status unsigned char SM; // middle sensor status unsigned char SR; // right sensor status #define E1 3 // speed control pin, ENA pin on motor driver shield #define E2 11 // speed control pin, ENA pin on motor driver shield #define M1 12 // motor direction control, IN1 pin on motor driver shield #define M2 13 // motor direction control, IN2 pin on motor driver shield void Sensor_IO_Config() { pinMode(SensorLeft,INPUT); pinMode(SensorMiddle,INPUT); pinMode(SensorRight,INPUT); } void Sensor_Scan(void) { SL = digitalRead(SensorLeft); SM = digitalRead(SensorMiddle); SR = digitalRead(SensorRight); } void M_Control_IO_config(void)// initialization function of motor driver shield IO { pinMode(M1,OUTPUT); pinMode(M2,OUTPUT); pinMode(E1,OUTPUT); pinMode(E2,OUTPUT); } void advance(void) // move forward { digitalWrite(M1,LOW); // wheel on the right moves forward digitalWrite(M2, LOW); // wheel on the left moves forward analogWrite(E1,150); analogWrite(E2, 150); } void turnR(void) // turn right { digitalWrite(M1,LOW); // wheel on the left moves forward digitalWrite(M2,HIGH); // wheel on the right moves backward analogWrite(E1,150); analogWrite(E2, 150); } void turnL(void) // turn left { digitalWrite(M1,HIGH); // wheel on the left moves backward digitalWrite(M2, LOW); // wheel on the right moves forward analogWrite(E1,150); analogWrite(E2, 150); } void stopp(void) // stop { digitalWrite(M1,LOW); digitalWrite(M2, LOW); analogWrite(E1, 0); analogWrite(E2, 0); // both right &left wheel stop } void back(void) // move backwards { digitalWrite(M1,HIGH); // both right &left wheel moves backwards digitalWrite(M2, HIGH); analogWrite(E1,150); analogWrite(E2, 150); } void setup() { Sensor_IO_Config(); M_Control_IO_config(); // initialization of motor controller module IO stopp(); } void loop() { Sensor_Scan(); if((SL==1&&SM==1&&SR==1)||(SL==1&&SM==1&&SR==0)||(SL==0&&SM==1&&SR==1)||(SL==0&&SM==1&&SR==0))advance(); if((SL==0&&SM==0&&SR==0)||(SL==0&&SM==0&&SR==1))turnL(); if(SL==1&&SM==0&&SR==0)turnR(); }
When the car enters line tracking mode, it begins constantly scanning I/O port of the MCU that connects the detecting sensor. When it picks up a signal of the I/O port , it will enter the judgment processing; firstly determine which sensor detects the black line.
Project 2: Obstacle-avoidance smart car
Introduction
This project is a simple obstacle avoidance smart car system based on Arduino. The controller part is a UNO board. An obstacle avoidance sensor is used to detect whether there is obstacle ahead, and feedback the signal to UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can automatically avoid obstacles.
Working principle
1. Obstacle avoidance sensor is applied here. The sensor has a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal.
2. When it detects an obstacle ahead, the sensor will output low level 0; when there is no obstacle detected, the sensor outputs high level signal 1.
3. To detect an obstacle, we only need a MCU to determine whether the sensor output is 0 or 1.
4. The MCU will control the car moving action according to the signal received.
Infrared obstacle avoidance sensor is equipped with a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube. The reflecting light strength is then converted into current signal. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1.
Note: you can adjust the potentiometer knob in the circuit to adjust the sensitivity of this line tracking module.
Performance parameter:
1. When it detects an obstacle, it outputs low level signal 0; when no obstacle is detected, it outputs high level signal 1. The sensor can be directly connected to the IO port of 3.3V or 5V MCU.
2. Detection distance is 2-40cm, long distance and high precision. (Note: for infrared sensor, the detection distance varies with difference in object color because different color has different reflectivity of light, the darker the object, the shorter the detection distance. The distance 2-40cm is calculated when the sensor is facing a white wall.)
3. Quick response, suitable for smart car obstacle avoidance, black and white line tracking, fall prevention, liquid level detection, etc.
4. Wide power supply range of 3-6V, suitable for using with 3.3-5V micro-controller.
5. Equipped with EN pin, when this pin output is “1”, the sensor is not operating; when the output is “0”, the sensor is. When the wire jumper on the module is put on, the EN pin is connected to GND and the output is “0”. If you want to use the EN pin, just take away the wire jumper.
6. Frequency adjusting potentiometer is used to adjust the carrier frequency of the infrared transmitting tube, because the integrated receiver is the most sensitive when in 38 KHZ carrier frequency. Adjust the 502 pot's clockwise to the upmost (that is when the transmitting tube is the brightest); then face the sensor to a white wall and adjust the 103 pot's until the detection distance is the furthest. Now the sensor is working at its best state.
Usage:
1. The sensor has 4 pins, namely GND, +, OUT, and EN. + and GND is for power supply; OUT is signal output pin. When in actual use, you only need to +, GND and OUT.
2. When an obstacle is detected, the signal pin outputs low level signal 0, when no obstacle detected, signal end outputs high level signal 1.
3. By determining whether the sensor output is 0 or 1, it can determine whether there is an obstacle ahead.
Module test program:
const int sensorPin = 2; // the number of the sensor pin const int ledPin = 13; // the number of the LED pin int sensorState = 0; // variable for reading the sensor status void setup() { pinMode(ledPin, OUTPUT); pinMode(sensorPin, INPUT); } void loop(){ // read the state of the sensor value: sensorState = digitalRead(sensorPin); // if it is, the sensorState is HIGH: if (sensorState == HIGH) { digitalWrite(ledPin, HIGH); } else { digitalWrite(ledPin, LOW); }}
Schematic and connection diagram
Obstacle avoidance car program
#define IRSensorLeft 10 // left sensor input pin #define IRSensorMiddle 9 // middle sensor input pin #define IRSensorRight 8 // right sensor input pin unsigned char IRSL; // left sensor status unsigned char IRSM; // middle sensor status unsigned char IRSR; // right sensor status #define E1 3 #define E2 11 #define M1 12 #define M2 13 void Sensor_IO_Config() { pinMode(IRSensorLeft,INPUT); pinMode(IRSensorMiddle,INPUT); pinMode(IRSensorRight,INPUT); } void Sensor_Scan(void) { IRSL = digitalRead(IRSensorLeft); IRSM = digitalRead(IRSensorMiddle); IRSR = digitalRead(IRSensorRight); } void M_Control_IO_config(void)// initialization function of motor driver shield IO { pinMode(M1,OUTPUT); pinMode(M2,OUTPUT); pinMode(E1,OUTPUT); pinMode(E2,OUTPUT); } void advance(void) // move forward { digitalWrite(M1,LOW); // right wheel moves forward digitalWrite(M2, LOW); // left wheel moves forward analogWrite(E1,150); analogWrite(E2, 150); } void turnR(void) // turn right { digitalWrite(M1,LOW); // left wheel moves forward digitalWrite(M2,HIGH); // right wheel moves backward analogWrite(E1,150); analogWrite(E2, 150); } void turnL(void) // turn left { digitalWrite(M1,HIGH); // left wheel moves backwards digitalWrite(M2, LOW); // right wheel moves forward analogWrite(E1,150); analogWrite(E2, 150); } void stopp(void) // stop { digitalWrite(M1,LOW); digitalWrite(M2, LOW); analogWrite(E1, 0); analogWrite(E2, 0); // both left and right wheels stop } void back(void) // move backward { digitalWrite(M1,HIGH); // both left and right wheels move forward digitalWrite(M2, HIGH); analogWrite(E1,150); analogWrite(E2, 150); } void setup() { Sensor_IO_Config(); M_Control_IO_config(); // initialization of motor driver shield IO stopp(); } unsigned char old_IRSL,old_IRSM,old_IRSR; void loop() { Sensor_Scan(); if(IRSL==1&&IRSM==1&&IRSR==1)advance(); if((IRSL==0&&IRSM==0&&IRSR==1)||(IRSL==0&&IRSM==1&&IRSR==1)||(IRSL==1&&IRSM==0&&IRSR==1))turnL(); if((IRSL==0&&IRSM==0&&IRSR==0)||(IRSL==1&&IRSM==0&&IRSR==0)||(IRSL==1&&IRSM==1&&IRSR==0))turnR(); }
Project 3: Bluetooth smart car
Introduction
This project is a smart car system based on Bluetooth communication, including software and hardware design. The controller part is a UNO board. A Bluetooth module is used to receive the Bluetooth signal from the cellphone and pass on to the UNO. UNO will analyze the signal to determine and control the motors movement to adjust car moving direction. Therefore the smart car can be controlled by cellphone.
Working principle
1. The UNO is connected to a Bluetooth module; the module communicates with cell phone through a Bluetooth APP.
2. The Bluetooth APP on the cell phone will pass information of “U”“D”“L”“R”“S” to the Bluetooth module.
3. The Bluetooth module will pass the information to the UNO, so the UNO can determine car movement according to the information received.
4. When the UNO receives a “U”, the car goes straight forward; when it receives a “D”, the car goes backward; “L” for turning left; “R” for turning right; and “S” for stop.
Bluetooth communication:
The term “Bluetooth” is derived from a Denmark king’s name in 10th century. The king is named Harald Blatand, while “Blatand” in English means Bluetooth.
The so-called bluetooth technology is actually a type of short distance wireless transmission technology. We can use “Bluetooth” to effectively simplify the communication between terminal devices such as laptop and mobile phone. It can also simplify communication between these devices and the Internet, thus improving the speed and efficiency of data transmission between them, widening the application scope of wireless communication.
Performance parameter:
1. The Bluetooth module used here is a HC-06 slave module. It has 4 pins namely VCC, GND, TXD and RXD.
2. With an LED indicator to indicate connection status, quick flashing means no Bluetooth connected; steadily on means Bluetooth is connected and the channel is open.
3. Module bottom is equipped with anti-reverse diode, with 3.3V LDO; input voltage between 3.6~6V. When the Bluetooth is not paired, the current is around 30mA; when Bluetooth is paired, current is around 10mA. The input voltage should not be over 7V.
4. Interface level is 3.3V, can be directly connected to various MCU (51, AVR, PIC, ARM, MSP430 etc.), also 5V MCU, no need for MAX232, and can not be used with MAX232.
5. 10m effective distance in open area (power class is CLASS 2). The distance can be further, but the connection quality can not be ensured.
6.Can be used as full duplex com after it’s paired, no need to have knowledge of any Bluetooth protocols; supports 8 data bit, 1 stop bit; can set up odd-even check communication format, which is the most commonly used communication format, does not support other formats.
7.Compact design (40mm*15.5mm), factory SMD production ensures quality; with transparent heat shrinkable film for dust-proof and anti-static.
8. Supports standard baud rate between 4800bps~1382400bps.
9. Module size: 40mm*15mm
Usage:
1. The sensor has 4 pins, GND, VCC, RX and TX. Connect main board +5V to Bluetooth VCC, main board GND to Bluetooth GND, main board TX to Bluetooth RX and RX to Bluetooth TX.
2. Remember to open the Bluetooth on your phone; when you open the Bluetooth APP, it will remind you.
3. Pair up Bluetooth device on your phone, search and pair.
4. Pair up device, PIN No. is 1234.
5. Open Bluetooth APP and pair up Bluetooth device. After it’s paired, the Bluetooth module can communicate with cell phone.
Module test:
Since this is your first try with Bluetooth module, we’ll do a simple test of having Arduino to successfully communicate with PC. First is the wire connection. Connect the module to the main board as stated in usage (refer to below figure). When the Bluetooth module is successfully connected to PC, the power indicator of the module will blink and connection indicator the green one will be on.
Now, let’s move on to the program. I’ll enter “r” and after Arduino receives my command “r”, the pin13 LED on the main board will blink and serial monitor will print “keyes”.
The program is as follows:
char val; int ledpin=13; void setup() { Serial.begin(9600); pinMode(ledpin,OUTPUT); } void loop() { val=Serial.read(); if(val=='r') { digitalWrite(ledpin,HIGH); delay(500); digitalWrite(ledpin,LOW); delay(500); Serial.println("keyes"); } }
Schematic and connection diagram
Bluetooth smart car program
Arduino Bluetooth remote control programmable smart car
// #define E1 3 #define E2 11 #define M1 12 #define M2 13 int val; void M_Control_IO_config(void)// initialization function of motor driver shield IO { pinMode(M1,OUTPUT); // pinMode(M2,OUTPUT); // pinMode(E1,OUTPUT); // pinMode(E2,OUTPUT); // } void advance(void) // move forward { digitalWrite(M1,LOW); // right wheel moves forward digitalWrite(M2, LOW); // left wheel moves forward analogWrite(E1,150); analogWrite(E2, 150); } void turnR(void) // turn right { digitalWrite(M1,LOW); // left wheel moves forward digitalWrite(M2,HIGH); // right wheel moves forward analogWrite(E1,150); analogWrite(E2, 150); } void turnL(void) // turn left { digitalWrite(M1,HIGH); // left wheel moves backward digitalWrite(M2, LOW); // right wheel moves forward analogWrite(E1,150); analogWrite(E2, 150); } void stopp(void) // stop { digitalWrite(M1,LOW); digitalWrite(M2, LOW); analogWrite(E1, 0); analogWrite(E2, 0); // both left and right wheel stop } void back(void) // move backward { digitalWrite(M1,HIGH); // both left and right wheel move backward digitalWrite(M2, HIGH); analogWrite(E1,150); analogWrite(E2, 150); } void setup() { Serial.begin(9600); M_Control_IO_config(); // initialization of motor driver shield IO stopp(); } void loop() { val=Serial.read(); if(val=='U')advance(); if(val=='D')back(); if(val=='L')turnL(); if(val=='R')turnR(); if(val=='S')stopp(); }
Resources
Please access this following link to get more details:
https://fs.keyestudio.com/KS0159