Ks0148 keyestudio W5100: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:


<br>
<br>
==keyestudio W5100==
==keyestudio W5100 Shield==
<br>[[File:ks0148-1.png|500px|frameless|thumb]]<br>
<br>[[File:ks0148-1.png|500px|frameless|thumb]]<br>


<br>
<br>
==Introduction==
==Introduction==
W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet controller inside,and applied to embedded system which is high integration, high stability, high performance and low cost. <br>
W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet controller inside,and applied to embedded system which is high integration, high stability, high performance and low cost. <br>
Line 27: Line 28:
<br>
<br>


<br>
==Sample Code==
==Sample Code==
'''Download Address of Libraries:'''<br>
<span style=color:red> '''Download Address of Libraries:''' </span><br>
https://drive.google.com/open?id=1IZkZQrfKms2zFcjLizQlt61Wu5Z0NeXr
https://drive.google.com/open?id=1IZkZQrfKms2zFcjLizQlt61Wu5Z0NeXr


Line 119: Line 122:
<br>
<br>
== Resources ==
== Resources ==
* '''PDF''' <br>
https://drive.google.com/open?id=1jGbfIC0GfmteezbCJePhSBavKATReNrr


* '''Libraries'''<br>
* '''Download Libraries and Code'''<br>
https://drive.google.com/open?id=15qCj2Yu9L3YApoVXYGcdPovWz8QlqxlD
 
https://fs.keyestudio.com/KS0148


*'''Code''' <br>
https://drive.google.com/open?id=1IZkZQrfKms2zFcjLizQlt61Wu5Z0NeXr





Latest revision as of 15:07, 6 January 2021


keyestudio W5100 Shield


thumb


Introduction

W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet controller inside,and applied to embedded system which is high integration, high stability, high performance and low cost.
It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX.
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer.
You don’t need to consider the control of Ethernet, and just need simple program of ports.


Specification

  • Various interface: Direct Bus, Indirect Bus and SPI Bus
  • Supporting TCP/IP protocol stack of hardware, TCP,UDP,ICMP,IGMP,IPv4,ARP
  • Up to 4 independent ports
  • Integrating 16KBYTE transmit-receive cache
  • Outputting multiple indicating information,including RX,TX,Full/Duplex,Colision,Link,Speed
  • Supporting automatic conversion of polarity
  • Coming with Internet access, dual row of 2*14 2.0mm pins


Connection Diagram


thumb

thumb



Sample Code

Download Address of Libraries:
https://drive.google.com/open?id=1IZkZQrfKms2zFcjLizQlt61Wu5Z0NeXr

#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,1,177);//modifying according your own IP
// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion
//of the response
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("<!DOCTYPE HTML>");
client.println("<html>");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("<br />");
}
client.println("</html>");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}




Result

After uploading program, you can input you own IP(matching with codes)on browser, and then press the “ENTER”key, showing the result(sometime you need to restart control board).


Resources

  • Download Libraries and Code

https://fs.keyestudio.com/KS0148



Buy From