Ks0112 keyestudio EASY plug Digital Push Button: Difference between revisions
Keyestudio (talk | contribs) |
Keyestudio (talk | contribs) |
||
| (5 intermediate revisions by the same user not shown) | |||
| Line 6: | Line 6: | ||
When the button is pressed, it outputs HIGH level signal; if release the button, it outputs LOW level signal.<br> | When the button is pressed, it outputs HIGH level signal; if release the button, it outputs LOW level signal.<br> | ||
You can simply connect to an IO port to have your first taste of Arduino.<br> | You can simply connect to an IO port to have your first taste of Arduino.<br> | ||
<span style= | This sensor needs to be used together with EASY plug control board.<br> | ||
<span style=color:red> '''Special Note:''' <br> | |||
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module. </span><br> | |||
<br> | <br> | ||
==Specification== | ==Specification== | ||
* Connector: Easy plug | * Connector: Easy plug | ||
| Line 27: | Line 31: | ||
<br> | <br> | ||
==Example 1: Button Controlled Light== | ==Example 1: Button Controlled Light== | ||
<br> | |||
'''Upload the Code'''<br> | '''Upload the Code'''<br> | ||
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly Mixly Blocks] and upload. <br> | Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly Mixly Blocks] and upload. <br> | ||
| Line 36: | Line 40: | ||
Powered up and upload well the code, press down the button, LED module is turned on. While release the button, LED is off. | Powered up and upload well the code, press down the button, LED module is turned on. While release the button, LED is off. | ||
<br>[[File:ks0397 4-1.png|500px|frameless|thumb]]<br> | <br>[[File:ks0397 4-1.png|500px|frameless|thumb]]<br> | ||
<br>[[File:ks0397 4- | <br>[[File:ks0397 4-3.png|500px|frameless|thumb]]<br> | ||
<br> | <br> | ||
Open the monitor, it will print out the value read from the button. | Open the monitor, it will print out the value read from the button. | ||
<br>[[File:ks0397 4- | <br>[[File:ks0397 4-2.png|500px|frameless|thumb]]<br> | ||
| Line 62: | Line 64: | ||
<br> | <br> | ||
==Resources == | ==Resources == | ||
https://fs.keyestudio.com/KS0112 | |||
<br> | <br> | ||
Latest revision as of 16:12, 7 January 2021
Introduction
The EASY Plug Push-button module is a tidy little design that lets you control a DC power source using an everyday tactile button.
This basic application module is widely applied to Arduino, Raspberry Pi platforms.
When the button is pressed, it outputs HIGH level signal; if release the button, it outputs LOW level signal.
You can simply connect to an IO port to have your first taste of Arduino.
This sensor needs to be used together with EASY plug control board.
Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.
Specification
- Connector: Easy plug
- Supply Voltage: 3.3V to 5V
- Large button and high-quality top cap
- Sensor type: Digital
Technical Details
- Dimensions: 38mm*20mm*18mm
- Weight: 5.6g
Connect It Up
Connect the EASY Plug push button sensor and LED module to control board using RJ11 cables.
Example 1: Button Controlled Light
Upload the Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.
What You Should See
Powered up and upload well the code, press down the button, LED module is turned on. While release the button, LED is off.
Open the monitor, it will print out the value read from the button.
Example 2: Simulating Table Lamp
Upload the Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.
What You Should See
Powered up and upload well the code, press down the button, LED light is turned on, it will not be off when release the button; But if press the button once again, LED will be turned off. It seems like your table lamp.
Open the monitor, you should be able to see how many times do you press the button.
Resources
https://fs.keyestudio.com/KS0112