Ks0273 keyestudio GY-ML8511 Ultraviolet Sensor Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(2 intermediate revisions by the same user not shown)
Line 25: Line 25:
<br>
<br>
==Sample Code ==
==Sample Code ==
Hooked up well, upload the below code to [https://wiki.keyestudio.com/How_to_Download_Arduino_IDE  Arduino software]. <br>


<pre>
<pre>
Line 53: Line 54:


<br>
<br>
==Result ==
==Result ==
Connect the wire and burn the program; after powered-on, open the serial monitor of Arduino IDE and see the value below.
Connect the wire and burn the program; after powered-on, open the serial monitor of Arduino IDE and see the value below.
Line 69: Line 71:
<br>
<br>
==Resource ==
==Resource ==
* '''PDF File:''' <br>
https://drive.google.com/open?id=16beq7w6udJhZLor3GUBm60EfuBXuS8s_


* '''Code:''' <br>
* '''Code:''' <br>
https://drive.google.com/open?id=1IGsXkg3cyV4e_BtbjQspYdD7B10BZtZa
https://fs.keyestudio.com/KS0273


* '''VIDEO:''' <br>
* '''VIDEO:''' <br>
Line 80: Line 80:


<br>
<br>
==Buy from ==
==Buy from ==
*[https://www.keyestudio.com/keyestudio-gy-ml8511-ultraviolet-sensor-module-for-arduino-black-ampamp-environmental-friendly-p0016.html    '''Official website''' ]
*[https://www.keyestudio.com/keyestudio-gy-ml8511-ultraviolet-sensor-module-for-arduino-black-ampamp-environmental-friendly-p0016.html    '''Official website''' ]

Latest revision as of 16:53, 8 January 2021

keyestudio GY-ML8511 Ultraviolet Sensor Module


Introduction

The module uses a common ML8511 UV sensor original, which can be used to detect indoor or outdoor UV density.
The sensor IC uses a high integrated SOI-CMOS technology, suitable for digital and analog circuits.
By the principle of converting the photocurrent to the voltage, it can detect the UV intensity and is well used for external circuits.
ML8511 can be proportional to the UV light quantity to output analog voltage, so it can be directly connected to the built-in MCU A / D digital / analog converter without photoelectric conversion circuit.
Using small and thin surface package, it is suitable for portable equipment.
The model also has a fast power saving mode up to 0.1uA, suitable for wearable smart devices, mobile phones and other equipment.

thumb


Specification

  • Working Voltage:DC 3.3-5V
  • Working Temperature:-20~70°C
  • Sensitive Area:UV-A, UV-B
  • Sensitive Wavelength: 280-390nm


Connection Diagram


thumb


Sample Code

Hooked up well, upload the below code to Arduino software.


/*
  AnalogReadSerial
  Reads an analog input on pin 0, prints the result to the serial monitor.
  Attach the center pin of a potentiometer to pin A0, and the outside pins to +5V and ground.

 This example code is in the public domain.
 */

// the setup routine runs once when you press reset:
void setup() {
  // initialize serial communication at 9600 bits per second:
  Serial.begin(9600);
}

// the loop routine runs over and over again forever:
void loop() {
  // read the input on analog pin 0:
  int sensorValue = analogRead(A0);
  // print out the value you read:
  Serial.println(sensorValue);
  delay(1);        // delay in between reads for stability
}


Result

Connect the wire and burn the program; after powered-on, open the serial monitor of Arduino IDE and see the value below.
thumb

When irradiating the sensor with ultraviolet light, the value changes shown below.
thumb


Further Learn

You can use this ultraviolet module to turn on an LED if you like. As shown below.
thumb



Resource

  • Code:

https://fs.keyestudio.com/KS0273

  • VIDEO:

http://video.keyestudio.com/ks0273/



Buy from