KS0464 KEYESTUDIO Smart Little Turtle Robot V3: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
 
(20 intermediate revisions by the same user not shown)
Line 1: Line 1:
Thanks for your support on our products, we will continue to provide you better quality and service!


'''About keyestudio''' 
Dear customer, we designed two versions of the motor drive shield for this robot kit, V1 version and V2 version, the shield will be shipped randomly with the robot.<br>
                     
Keyestudio is a best-selling brand owned by KEYES Corporation, our product lines range from Arduino boards, shields, sensor modules, Raspberry Pi, micro:bit extension boards and smart car to complete starter kits designed for customers of any level to learn Arduino knowledge. <br>
All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.
Welcome check more contents from our official website:<br>
http://www.keyestudio.com <br>


'''References and After-sales Service'''
We are very sorry for any inconvenience caused by this.<br> 


1.Download Profile:https://fs.keyestudio.com/KS0464<br>
V1 and V2 version motor drive shield for reference:<br>
2.Feel free to contact us please, if there is missing part or you encounter some troubles. Welcome to send email to us:service@keyestudio.com. We will update projects and products continuously based on your sincere advice.<br>


<br>[[File:图片168.png|500px|frameless|thumb]]<br>


'''Warning'''


1.This product contains tiny parts(screws, copper pillars), keep it out of reach of children under 7 years old please..<br>
Thanks for your support on our products, we will continue to provide you better quality and service!
2.This product contains conductive parts (control board and electronic module). Please operate according to the requirements of this tutorial. Improper operation may cause overheating and damage parts. Do not touch and immediately disconnect the circuit power.<br>
 
'''Copyright'''
 
The keyestudio trademark and logo are the copyright of KEYES DIY ROBOT co.,LTD. All products under keyestudio brand can’t be copied, sold and resold without authorization by anyone or company. If you’re interested in our items, please contact to our sales representatives: fennie@keyestudio.com
 
 
<br>[[File:0464-==.png|500px|frameless|thumb]]<br>
 
== Introduction ==
                                             
Nowadays, technological education such as VR, kids programming, and artificial intelligence, has become mainstream in educational industry. <br>
Thereby, people attach importance to STEAM education. Arduino is pretty notable in Maker education.<br>
 
So what is Arduino? Arduino is an open-source electronics platform based on easy-to-use hardware and software. Arduino boards are able to read inputs - light on a sensor, a finger on a button, or a Twitter message - and turn it into an output - activating a motor, turning on an LED, publishing something online. Based on this, Keyestudio team has designed a turtle robot. It has a processor which is programmable using the Arduino IDE, to mapped its pins to sensors and actuators by a shield that plug in the processor, it reads sensors and controls the actuators and decides how to operate.<br>
 
15 learning projects, from simple to complex, will guide you how to make a smart turtle robot on you own and introduce the detailed knowledge about sensors and modules. <br>
 
Simultaneously, it is the best choice if you intend to obtain a DIY robot for learning programming, entertainment and competition requirement.<br>
 
== Features == 
                                                   
* Multi-purpose function: Obstacle avoidance, follow, IR remote control, Bluetooth control, ultrasonic follow and displayed face emoticons.
* Simple assembly: No soldering circuit required, complete assembly easily.
* High Tenacity: Aluminum alloy bracket, metal motors, high quality wheels and tracks
* High extension: expand other sensors and modules through motor driver shield and sensor shield
* Multiple controls: IR remote control, App control(iOS and Android system)
* Basic programming:C language code of Arduino IDE.
 
 
== Specification ==
                             
 
* Working voltage: 5v
* Input voltage: 7-12V
* Maximum output current: 2A
* Maximum power dissipation: 25W (T=75℃)
* Motor speed: 5V 63 rpm/min
* Motor drive mode: dual H bridge drive
* Ultrasonic induction angle: <15 degrees
* Ultrasonic detection distance: 2cm-400cm
* Infrared remote control distance: 10M (measured)
* Bluetooth remote control distance: 50M(measured)
* Bluetooth control: support Android and iOS system
 
 
== Product Kit ==
 
<br>[[File:0464=1.png|500px|frameless|thumb]]<br>
 
<br>[[File:0464=2.png|700px|frameless|thumb]]<br>
[[File:0464=3.png|700px|frameless|thumb]]
<br>[[File:0464=4.png|700px|frameless|thumb]]<br>
[[File:0464=5.png|700px|frameless|thumb]]
<br>[[File:0464=7.png|700px|frameless|thumb]]<br>
 
 
== Assembly Guide == 
 
Step 1: Bottom Motor Wheel
 
Prepare the parts as follows:
 
* M3*6MM Round Head Screw *2
* M3*6MM Flat Head Screw *2
* M3 Nickel Plated Nut *2
* Bottom PCB*1
* Tracking Sensor *1
* Universal Caster *2
 
<br>[[File:0464=8.png|500px|frameless|thumb]]<br>
 
Step 2:Assemble Parts
 
Prepare the parts as follows:
 
 
* M3*6MM Round Head Screw *2
* M2 Nut *4
* 12FN20 Motor *2
* U-type Holder* 2
* N20 Motor Wheel *2
* 2P Wire *2
* 5P Wire *1
* M2*12MM Round Head Screw *4
* 2-cell AA Battery Holder *1
* M3*6M Flat Head Screw *2
* M3 Nut *2
 
 
 
<br>[[File:0464=9.png|500px|frameless|thumb]]<br>
<br>[[File:0464=10.png|500px|frameless|thumb]]<br>
<br>[[File:0464=11.png|500px|frameless|thumb]]<br>
<br>[[File:0464=12.png|500px|frameless|thumb]]<br>
<br>[[File:0464=13.png|500px|frameless|thumb]]<br>
<br>[[File:0464=14.png|500px|frameless|thumb]]<br>
 
Step 3: Install Top PCB
Prepare the parts as follows:
 
* Top PCB *1
* M3 Nut *1
* M3*6MM Round Head Screw *9
* M3*10MM Hexagon Copper Bush *8
* IR Receiver Sensor *1
 
<br>[[File:0464=15.png|500px|frameless|thumb]]<br>
 
 
Step 4: Mount Control Board
 
Prepare the parts as follows:
 
* V4.0 Board*1
* Motor Drive Shield V2*1
* M3*6MM Round Head Screw *4
 
 
 
<br>[[File:0464=16.png|500px|frameless|thumb]]<br>
<br>[[File:0464=17.png|500px|frameless|thumb]]<br>
 
 
 
Step 5: Servo Plastic Platform
Prepare the parts as follows:
 
* Servo *1
* M2*4 Screw *1
* Black Tie*2
* Ultrasonic Sensor*1
* Black Plastic Platform *1
* M1.2*4 Tapping Screw *4
* M2*8 Tapping Screw *2
 
 
 
<br>[[File:0470---21.png|500px|frameless|thumb]]<br>
<br>[[File:0464=19.png|500px|frameless|thumb]]<br>
<br>[[File:0464=20.png|500px|frameless|thumb]]<br>
<br>[[File:0464=21.png|500px|frameless|thumb]]<br>
<br>[[File:0464=22.png|500px|frameless|thumb]]<br>
 
 
 
Step 6: Final Assembly
 
Prepare the parts as follows:
 
* M3*6MM Round Head Screw *12
* M3*40MM Hexagon Copper Bush*4
* 8x8 Dot Matrix *1
* Jumper Wire *4
 
 
 
<br>[[File:0464=23.png|500px|frameless|thumb]]<br>
<br>[[File:0464=24.png|500px|frameless|thumb]]<br>
<br>[[File:0464=25.png|500px|frameless|thumb]]<br>
<br>[[File:0464=26.png|500px|frameless|thumb]]<br>
 
 
 
Step 7: Hook-up Guide
 
<br>[[File:0464=27.png|500px|frameless|thumb]]<br>
<br>[[File:0464=28.png|500px|frameless|thumb]]<br>
<br>[[File:0464=29.png|500px|frameless|thumb]]<br>
<br>[[File:0464=30.png|500px|frameless|thumb]]<br>
<br>[[File:0464=31.png|500px|frameless|thumb]]<br>
<br>[[File:0464=32.png|500px|frameless|thumb]]<br>
 
 
== Getting Started with Arduino ==
 
When we get control board, we need to download Arduino IDE and driver firstly.
You could download Arduino IDE from the official website:
https://www.arduino.cc/, click the SOFTWARE on the browse bar, click “DOWNLOADS” to enter download page, as shown below:
 
<br>[[File:0085=04.png|500px|frameless|thumb]]<br>
 
There are various versions for Arduino, just download a suitable version for your system, we will take WINDOWS system as an example to show you how to download and install.
 
<br>[[File:04862png.png|500px|frameless|thumb]]<br>
 
There are two versions for WINDOWS system, one is installed version, another one is download version, you just need to download file to computer directly and unzip it. These two versions can be used normally. Choose one and download on your computer.
 
<br>[[File:04863png.png|500px|frameless|thumb]]<br>
 
You just need to click JUST DOWNLOAD, then click the downloaded file to install it. And when the ZIP file is downloaded, you can directly unzip and start it.
 
 
We need to know keyestudio V4.0 development board, as a core of this smart car.
 
<br>[[File:0077-78--1.png|400px|frameless|thumb]]<br>
 
(1)Keyestudio V4.0 Development Board
 
keyestudio V4.0 development board is an Arduino uno-compatible board, which is based on ATmega328P MCU, and with a cp2102 Chip as a UART-to-USB converter. 
 
<br>[[File:0470---42.png|500px|frameless|thumb]]<br>
 
It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, 2 ICSP headers and a reset button.
 
<br>[[File:0428---1000.png|500px|frameless|thumb]]<br>
 
It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it via an external DC power jack (DC 7-12V) or via female headers Vin/ GND(DC 7-12V) to get started.
 
<br>[[File:0470---40.png|500px|frameless|thumb]]<br>
 
 
 
=== Installing driver ===
 
Let’s install the driver of keyestudio PLUS control board. The USB-TTL chip on PLUS board adopts CP2102 serial chip. The driver program of this chip is included in Arduino 1.8 version and above, which is convenient. Plug on USB port of board, the computer can recognize the hardware and automatically install the driver of CP2102.
 
If install unsuccessfully, or you intend to install manually, open the device manager of computer. Right click Computer----- Properties----- Device Manager.
 
<br>[[File:0085=07.png|700px|frameless|thumb]]<br>
 
There is a yellow exclamation mark on the page, which implies installing the driver of CP2102 unsuccessfully. Then we double click the hardware and update the driver.
 
<br>[[File:0085=08.png|500px|frameless|thumb]]<br>
 
Click “OK” to enter the following page, click “browse my computer for updated driver software”, find out the installed or downloaded ARDUINO software. As shown below:
 
<br>[[File:0085=09.png|500px|frameless|thumb]]<br>
 
There is a DRIVERS folder in Arduino software installed package([[File:0085=10.png|500px|frameless|thumb]]), open driver folder and you can see the driver of CP210X series chips.
 
 
We click “Browse”, then find out the driver folder, or you could enter “driver” to search in rectangular box, then click “next”, the driver will be installed successfully. (I place Arduino software folder on the desktop, you could follow my way)
 
<br>[[File:0085=11.png|500px|frameless|thumb]]<br>
 
 
Open device manager, we will find the yellow exclamation mark disappear. The driver of CP2102 is installed successfully.
<br>[[File:0085=12.png|500px|frameless|thumb]]<br>
<br>[[File:0085=13.png|500px|frameless|thumb]]<br>
 
 
 
=== Install other visions of driver ===
 
 
 
 
 
 
 
 
 
=== Arduino IDE Setting ===
 
 
 
 
 
=== Start First Program ===
 
 
 
 
== Add project Libraries ==
                                 
=== What are Libraries ? ===




=== How to Install a Library ? ===
Tutorial for the robot with V1 motor shield: https://fs.keyestudio.com/KS0464oo<br>
Tutorial for the robot with V2 motor shield: https://fs.keyestudio.com/KS0464<br>




== Projects ==
After-sales service:<br>


For more projects or Mixly projects, please navigate link: https://fs.keyestudio.com/KS0464
For Amazon platform: service@keyestudio.com<br>
For AliExpress: tivon2944150264@outlook.com<br>
Other Channels: sunny@keyestudio.com<br>

Latest revision as of 10:44, 20 July 2023

Dear customer, we designed two versions of the motor drive shield for this robot kit, V1 version and V2 version, the shield will be shipped randomly with the robot.

We are very sorry for any inconvenience caused by this.

V1 and V2 version motor drive shield for reference:


thumb


Thanks for your support on our products, we will continue to provide you better quality and service!


Tutorial for the robot with V1 motor shield: https://fs.keyestudio.com/KS0464oo
Tutorial for the robot with V2 motor shield: https://fs.keyestudio.com/KS0464


After-sales service:

For Amazon platform: service@keyestudio.com
For AliExpress: tivon2944150264@outlook.com
Other Channels: sunny@keyestudio.com