Ks0026 keyestudio Digital IR Receiver Module: Difference between revisions
Jump to navigation
Jump to search
Keyestudio (talk | contribs) |
Keyestudio (talk | contribs) |
||
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
<br> | |||
==Introduction== | ==Introduction== | ||
IR is widely used in remote control. With this IR receiver, Arduino project is able to receive command from any IR remoter controllers if you have | IR is widely used in remote control. With this IR receiver, Arduino project is able to receive command from any IR remoter controllers if you have right decoder. Well, it will be also easy to make your own IR controller using IR transmitter. | ||
<br>[[File:KS0026 (3).jpg|500px|frameless|thumb]]<br> | <br>[[File:KS0026 (3).jpg|500px|frameless|thumb]]<br> | ||
<br> | |||
==Specification== | ==Specification== | ||
*Power Supply: 5V | *Power Supply: 5V | ||
*Interface:Digital | *Interface: Digital | ||
*Modulation Frequency: 38Khz | *Modulation Frequency: 38Khz | ||
<br> | |||
==Connection Diagram == | ==Connection Diagram == | ||
The following image shows a suggested connection method. You may use any Digital I/O pin that is not in use by another device. | The following image shows a suggested connection method. You may use any Digital I/O pin that is not in use by another device. | ||
<br>[[File:Ks0026.png|700px|frameless|thumb]]<br> | |||
NOTE: In the sample code below Digital pin 11 is in use, you may either change your wiring or change the sample code to match. | <span style=color:red> '''NOTE:''' In the sample code below Digital pin 11 is in use, you may either change your wiring or change the sample code to match. <br> | ||
<br> | |||
==Sample Code == | ==Sample Code == | ||
<span style=color:red> '''Note:''' before compiling the code, do remember to place the library into libraries directory of Arduino IDE. Otherwise, compiling will fail. <br> | |||
<pre> | <pre> | ||
#include <IRremote.h> | #include <IRremote.h> | ||
int RECV_PIN = 11; | int RECV_PIN = 11; | ||
| Line 35: | Line 36: | ||
Serial.println(results.value, HEX); | Serial.println(results.value, HEX); | ||
irrecv.resume(); // Receive the next value | irrecv.resume(); // Receive the next value | ||
}</pre> | } | ||
} | |||
</pre> | |||
= | <br> | ||
<br>[ | <span style=color:red> | ||
IR Remote Library includes some sample codes for sending and receiving: <br> | |||
[https://github.com/shirriff/Arduino-IRremote IR Remote Library] | |||
<br> | |||
== Result == | |||
Done wiring and uploading the code, then control the IR receiver module by an infrared remote control, D1 led will flash. Shown as below. | |||
<br>[[File:KS0349 33-4.png|600px|frameless|thumb]]<br> | |||
<br> | |||
==Resources == | ==Resources == | ||
''' | * '''All Info.'''<br> | ||
https://fs.keyestudio.com/KS0026 | |||
''' | * '''Video'''<br> | ||
http://video.keyestudio.com/ks0026/ | |||
<br> | |||
==Buy from == | ==Buy from == | ||
*[https://www.keyestudio.com/free-shipping-keyestudio-digital-ir-infrared-receiver-module-for-arduino-uno-r3-mega-2560-r3-p0151.html '''Official Website'''] | |||
*[https://www.aliexpress.com/store/product/Free-shipping-Keyestudio-38kHz-1838-Universal-Digital-IR-Infrared-Receiver-Module-for-Arduino-UNO-R3/4247007_32887932794.html?spm=2114.12010615.8148356.13.53827852viTGyz '''Shop on aliexpress''' ] | |||
[[Category: Sensor]] | [[Category: Sensor]] | ||
Latest revision as of 10:49, 2 March 2021
Introduction
IR is widely used in remote control. With this IR receiver, Arduino project is able to receive command from any IR remoter controllers if you have right decoder. Well, it will be also easy to make your own IR controller using IR transmitter.
.jpg)
Specification
- Power Supply: 5V
- Interface: Digital
- Modulation Frequency: 38Khz
Connection Diagram
The following image shows a suggested connection method. You may use any Digital I/O pin that is not in use by another device.
NOTE: In the sample code below Digital pin 11 is in use, you may either change your wiring or change the sample code to match.
Sample Code
Note: before compiling the code, do remember to place the library into libraries directory of Arduino IDE. Otherwise, compiling will fail.
#include <IRremote.h>
int RECV_PIN = 11;
IRrecv irrecv(RECV_PIN);
decode_results results;
void setup()
{
Serial.begin(9600);
irrecv.enableIRIn(); // Start the receiver
}
void loop() {
if (irrecv.decode(&results)) {
Serial.println(results.value, HEX);
irrecv.resume(); // Receive the next value
}
}
IR Remote Library includes some sample codes for sending and receiving:
IR Remote Library
Result
Done wiring and uploading the code, then control the IR receiver module by an infrared remote control, D1 led will flash. Shown as below.
Resources
- All Info.
https://fs.keyestudio.com/KS0026
- Video
http://video.keyestudio.com/ks0026/