Ks0148 keyestudio W5100: Difference between revisions
Keyestudio (talk | contribs) (Created page with "==keyestudio W5100== <br>500px|frameless|thumb<br> ==Introduction== W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet...") |
Keyestudio (talk | contribs) |
||
| Line 108: | Line 108: | ||
== Resources == | == Resources == | ||
''' | '''PDF''' <br> | ||
https://drive.google.com/open?id=18YYdUboF_gjbShiyBKfh5lEvilyLlIph | |||
'''Libraries''' | |||
https://drive.google.com/open?id=15qCj2Yu9L3YApoVXYGcdPovWz8QlqxlD | |||
== Buy From == | == Buy From == | ||
Revision as of 16:14, 15 November 2017
keyestudio W5100
Introduction
W5100 is a multi-purpose single internet interface chip, integrated 10/100 ethernet controller inside,and applied to embedded system which is high integration, high stability, high performance and low cost. It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX. It contains TCP/IP protocol stack that is full-hardware and verified by market for years, ethernet medium transport layer and physical layer. You don’t need to consider the control of ethernet, and just need simple program of ports.
Specification
- Various interface: Direct Bus, Indirect Bus and SPI Bus
- Supporting TCP/IP protocol stack of hardware, also TCP,UDP,ICMP,IGMP,IPv4，ARP and PPPoE
- Up to 4 independent ports
- Integrating 16KBYTE transmit-receive cache
- Outputting multiple indicating information,including RX,TX,Full/Duplex,Colision,Link,Speed
- Supporting automatic conversion of polarity
- Coming with Internet access, dual row of 2*14 2.0mm pins
Connection Diagram
Sample Code
#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = {
0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,1,177);//modifying according your own IP
// Initialize the Ethernet server library
// with the IP address and port you want to use
// (port 80 is default for HTTP):
EthernetServer server(80);
void setup() {
// Open serial communications and wait for port to open:
Serial.begin(9600);
while (!Serial) {
; // wait for serial port to connect. Needed for Leonardo only
}
// start the Ethernet connection and the server:
Ethernet.begin(mac, ip);
server.begin();
Serial.print("server is at ");
Serial.println(Ethernet.localIP());
}
void loop() {
// listen for incoming clients
EthernetClient client = server.available();
if (client) {
Serial.println("new client");
// an http request ends with a blank line
boolean currentLineIsBlank = true;
while (client.connected()) {
if (client.available()) {
char c = client.read();
Serial.write(c);
// if you've gotten to the end of the line (received a newline
// character) and the line is blank, the http request has ended,
// so you can send a reply
if (c == '\n' && currentLineIsBlank) {
// send a standard http response header
client.println("HTTP/1.1 200 OK");
client.println("Content-Type: text/html");
client.println("Connection: close"); // the connection will be closed after completion
//of the response
client.println("Refresh: 5"); // refresh the page automatically every 5 sec
client.println();
client.println("<!DOCTYPE HTML>");
client.println("<html>");
// output the value of each analog input pin
for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
int sensorReading = analogRead(analogChannel);
client.print("analog input ");
client.print(analogChannel);
client.print(" is ");
client.print(sensorReading);
client.println("<br />");
}
client.println("</html>");
break;
}
if (c == '\n') {
// you're starting a new line
currentLineIsBlank = true;
}
else if (c != '\r') {
// you've gotten a character on the current line
currentLineIsBlank = false;
}
}
}
// give the web browser time to receive the data
delay(1);
// close the connection:
client.stop();
Serial.println("client disonnected");
}
}
Download Address of Libraries：
http://7326097.s21d-7.faiusrd.com/0/ABUIABAAGAAgs4zWvQUokJuN5wU?f=KS0148+Libraries.zip&v=1471514163
Result
After uploading program, you can input you own IP(matching with codes)on browser, and then press “ENTER”key, showing the result(sometime you need to restart control board.).
Resources
PDF
https://drive.google.com/open?id=18YYdUboF_gjbShiyBKfh5lEvilyLlIph
Libraries
https://drive.google.com/open?id=15qCj2Yu9L3YApoVXYGcdPovWz8QlqxlD