Ks0243 keyestudio EASY plug W5100 Ethernet Module

EASY plug W5100 Ethernet Module

Introduction

W5100 is a multi-purpose single internet interface chip, integrated 10/100 Ethernet controller inside, and applied to embedded system which is high integration, high stability, high performance and low cost.
It can be connected to Internet without operating system and compatible with IEEE802.3 10BASE-T and 802.3u 100BASE-TX.
It contains TCP/IP protocol stack that is full-hardware and verified by market for years, Ethernet medium transport layer and physical layer. You don’t need to consider the Ethernet control, and just need simple program for ports.
The module should be connected to the SPI communication interface on EASY plug control board with only one cable, so the wiring is rather simple.

Specifications

• Various interface: Direct Bus, Indirect Bus and SPI Bus
• Supporting TCP/IP protocol stack of hardware, also TCP, UDP, ICMP, IGMP, IPv4, ARP and PPPoE
• Up to 4 independent ports
• Integrating 16KBYTE transmit-receive cache
• Supporting automatic conversion of polarity
• Coming with Internet access

Technical Details

• Dimensions: 61mm*30mm*18mm
• Weight: 14.1g

Connect It Up

Connect the EASY Plug W5100 Ethernet module to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.

Upload the Code

Copy and paste below code to Arduino IDE and upload.
Note: before compile the code, do remember to place the necessary libraries inside the libraries directory of Arduino IDE.
You can download the libraries from the link: https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG

#include <SPI.h>
#include <Ethernet.h>
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
LiquidCrystal_I2C lcd(0x27,20,4); 

// Enter a MAC address for your controller below.
// Newer Ethernet shields have a MAC address printed on a sticker on the shield
byte mac[] = {  
  0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02 };

// Initialize the Ethernet client library
// with the IP address and port of the server 
// that you want to connect to (port 80 is default for HTTP):
EthernetClient client;
void setup() {
  Serial.begin(9600);
  lcd.init();
  lcd.backlight();
}

void loop() {
 ///////////////////////////////////////////////////////////// W5100
 delay(1000); 
 lcd.clear();
 lcd.setCursor(0,0);
 lcd.print("T ..."); 
  if (Ethernet.begin(mac) == 0)  
  {
    lcd.setCursor(0,1);
    lcd.print("W5100 Error!");
    Serial.println("W5100 Error!");
    while(1);
  }
  lcd.setCursor(0,1);
  for (byte thisByte = 0; thisByte < 4; thisByte++) {
   lcd.print(Ethernet.localIP()[thisByte], DEC);
   lcd.print(".");
   Serial.print(Ethernet.localIP()[thisByte], DEC);
   Serial.print(".");
  }
  lcd.setCursor(14,1);
  lcd.print("OK");  
  Serial.println("OK");
  //while(1);
}

What You Should See

Done uploading the test code, open the serial monitor and set the baud rate to 9600, you should be able to check the IP address that W5100 Ethernet module connected.

Resources

Download the PDF:
https://drive.google.com/open?id=1p7rEYMu5YAaGPQpOddhlyCLMpdV5mDPl

Download the Code:
https://drive.google.com/open?id=1BpRSrwKWN_ff6cEQ6xhqklH1shjVc4fQ

Download the libraries:
https://drive.google.com/open?id=18_Ye5Ew1TrpnBsLUO4J9rvEqqoUL-DJG

Buy from

• Official Website: http://www.keyestudio.com/ks0243.html

• Shop on aliexpress