Ks0271 keyestudio OLED Display OLED Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 94: Line 94:
*[https://www.aliexpress.com/store/product/Keyestudio-0-96-OLED-Module-128X64-Blue-LCD-LED-Display-Module-IIC-Serial/1452162_32823394893.html?spm=2114.12010615.8148356.5.6dd228c1lb6ljy      '''Shop on aliexpress''' ]
*[https://www.aliexpress.com/store/product/Keyestudio-0-96-OLED-Module-128X64-Blue-LCD-LED-Display-Module-IIC-Serial/1452162_32823394893.html?spm=2114.12010615.8148356.5.6dd228c1lb6ljy      '''Shop on aliexpress''' ]


*[https://www.amazon.com/dp/B078YQDZ17  '''Shop on amazon''' ]




[[Category: Module]]
[[Category: Module]]

Revision as of 15:58, 5 November 2019


keyestudio 0.96 OLED Display Module


thumb


Introduction

OLED is short for organic light emitting diode. On the microscopic level, an OLED display is a matrix of organic LEDs that light up when they emit energy.
Old LCD (Liquid Crystal Display) technology uses electronically controlled polarizers to change the way light passes or does not pass through them. This requires an external backlight that lights up the whole display underneath. This uses a lot of energy because at the time the display is on, enough light for all pixels must be provided.
The new OLED technology only uses electricity per pixel. Because each pixel creates its own light, only the pixels that are on use electricity. This makes OLED technology very efficient; also, the way these types of OLEDs are built allows them to be very thin compared to LCD.

thumb


Specification

  • Supply Voltage: 3.3V to 5V
  • Number of Pixels:128 × 64
  • Color Depth:blue
  • Communication way: IIC


Connection Diagram


thumb


Sample Code

#include <SPI.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

#define OLED_RESET 4
Adafruit_SSD1306 display(OLED_RESET);

void setup() {

// by default, we'll generate the high voltage from the 3.3v line internally! (neat!)
display.begin(SSD1306_SWITCHCAPVCC, 0x3C); // initialize with the I2C addr 0x3D (for the 128x64)
// init done

// Show image buffer on the display hardware.
// Since the buffer is intialized with an Adafruit splashscreen
// internally, this will display the splashscreen.
display.display();
delay(2000);

// Clear the buffer.
display.clearDisplay();
}

void loop() {

display.clearDisplay();
display.setTextSize(1);
display.setTextColor(WHITE);
display.setCursor(0,0);
display.println("Hello,world!");
display.println("Hello,keyestudio!");
display.setTextSize(2);
display.println("Hello!");
display.println("keyes!");
display.println("keyestudio");
display.display();
delay(250);
}


Result

Wiring as the above diagram and burning the code, after power-on, OLED display will as the graph shown below.

thumb


Resource

  • PDF File:

https://drive.google.com/open?id=1ksYXWqnel7kQjDK1c9mCSRpW6FphaOay

  • Code:

https://drive.google.com/open?id=1w8g0MFWgW-HVBDTVgmn_7vyJDfI_Kq_L

  • Four Libraries of OLED Display Module:

https://drive.google.com/open?id=1VneczfQemtHSrRf4cDYMrZlclz55CR7l

  • VIDEO:

http://video.keyestudio.com/ks0271/



Buy from