Ks0266 keyestudio Eight-channel Solid State Relay Module: Difference between revisions
Keyestudio (talk | contribs) |
Keyestudio (talk | contribs) |
||
Line 138: | Line 138: | ||
*[https://www.aliexpress.com/store/product/Free-shiping-Eight-Channel-Solid-State-Relay-Module-red-for-arduino/1452162_32318526166.html?spm=2114.12010615.8148356.3.513973a5GQGFM4 '''Shop on aliexpress''' ] | *[https://www.aliexpress.com/store/product/Free-shiping-Eight-Channel-Solid-State-Relay-Module-red-for-arduino/1452162_32318526166.html?spm=2114.12010615.8148356.3.513973a5GQGFM4 '''Shop on aliexpress''' ] | ||
*[https://www.amazon.com/dp/B07DR9PX7P '''Shop on amazon''' ] | |||
[[category:Module]] | [[category:Module]] |
Revision as of 16:05, 5 November 2019
Keyestudio Eight-channel Solid State Relay Module
Introduction
Keyestudio eight-channel solid state relay is active at HIGH level, that is to say, the input control signal is the high level (3.3-5 V), the relay is on; while the input control signal is high level (0-2.5 V), the relay is off.
Solid State Relay is a new kind of contactless switching device, which is composed of all solid state electronic components.
Compared with the electromagnetic relay, it has higher reliability, with the features of non-contact, long service life, fast speed and less outside interference.
The output control terminal of keyestudio solid-state relay must be connected to the circuit, can only be AC (Alternating Current) , so that the solid state relay can be disconnected normally.
Performance Parameters
- Electrical parameters:
Voltage | Static Current | Working Current | Trigger Voltage | Trigger Current | |
---|---|---|---|---|---|
Channel 1 | DC 5V | 0mA | 13.8mA | 3.3-5V | 2mA |
Channel 2 | DC 5V | 0mA | 26.8mA | 3.3-5V | 2mA |
Channel 3 | DC 5V | 0mA | 37mA | 3.3-5V | 2mA |
Channel 4 | DC 5V | 0mA | 48mA | 3.3-5V | 2mA |
Channel 5 | DC 5V | 0mA | 59mA | 3.3-5V | 2mA |
Channel 6 | DC 5V | 0mA | 70mA | 3.3-5V | 2mA |
Channel 7 | DC 5V | 0mA | 81mA | 3.3-5V | 2mA |
Channel 8 | DC 5V | 0mA | 90mA | 3.3-5V | 2mA |
- Output port: AC240V/2A
Connection Diagram
Sample Code
int BASE = 3 ; //The first relay I/O port int NUM = 8 ; //Total number of relay void setup() { for (int i = BASE; i < BASE + NUM; i ++) { pinMode(i, OUTPUT); //Set the digital I/O port to output } } void loop() { for (int i = BASE; i < BASE + NUM; i ++) { digitalWrite(i, HIGH); //Set the digital I/O port outputs to "HIGH", that is, gradually open relay delay(200); //delay } for (int i = BASE; i < BASE + NUM; i ++) { digitalWrite(i, LOW); //Set the digital I/O port outputs to "LOW", that is, gradually close relay delay(200); //delay } }
Result
Wiring as the above image, after powered-on, eight-channel solid state relays are first connected and then broken successively,repeating alternately.
Resource
- PDF:
https://drive.google.com/open?id=1bVGkOans_UoWegSrJs8Ft3D4GEKakp-1
- Code:
https://drive.google.com/open?id=1tOdLplPqGoc6RrVa1OffPwOZtjCF9Axl