KS0221 keyestudio Ultimate Starter Kit for Raspberry Pi
keyestudio Ultimate Starter Kit for Raspberry Pi
Kit Introduction
Raspberry Pi is a delicate card computer. This is a starter kit of Raspberry Pi, very suitable for zero-based raspberry pi enthusiasts. Through this kit, you can learn more about the knowledge of linux operating system, as well as C, python and other language programming based on the debian system of Raspberry Pi. This kit also provides you with some related sensors and modules applied to the Raspberry Pi.
We offer richer learning materials that allow you to learn about Raspberry Pi from scratch. The learning materials include the installation and usage of the Raspberry Pi related system, where also offer you the learning courses of Raspberry Pi collocated with some commonly used sensors and modules. It would be better If you are an arduino hobbyist because arduino and Raspberry Pi are the best partners. You can make more creative DIY works via arduino strong community support and rich third-party library resources, integrating into Raspberry Pi's powerful function support to motivate your creativity and inspiration!
Kit List
| No. | Product Name | Quantity | Picture |
|---|---|---|---|
| 1 | Keyestudio RPI GPIO-PCF8591 Shield | 1 |  |
| 2 | LED - Blue | 5 |  |
| 3 | LED - Red | 5 |  |
| 4 | LED - Yellow | 5 |  |
| 5 | LED - RGB | 1 |  |
| 6 | 220Ω Resistor | 8 |  |
| 7 | 10KΩ Resistor | 5 |  |
| 8 | 1KΩ resistor | 5 |  |
| 9 | 10KΩ Potentiometer | 1 |  |
| 10 | Buzzer (active) | 1 |  |
| 11 | Buzzer (passive) | 1 |  |
| 12 | Large Button Switch | 4 |  |
| 13 | Ball Tilt Sensor | 2 |  |
| 14 | Photo Resistor | 3 |  |
| 15 | Flame Sensor | 1 |  |
| 16 | LM35 Temp Sensor | 1 |  |
| 17 | IC 74HC595N 16-pin | 1 |  |
| 18 | 1-digit LED | 1 |  |
| 19 | 4-digit LED | 1 |  |
| 20 | 8*8 LED Matrix | 1 |  |
| 21 | 2x16 LCD display | 1 |  |
| 22 | IR Receiver | 1 |  |
| 23 | IR Remote Control | 1 |  |
| 24 | Servo Motor | 1 |  |
| 25 | Stepper Driver | 1 |  |
| 26 | Stepper Motor | 1 |  |
| 27 | Joystick Module | 1 |  |
| 28 | Relay Module | 1 |  |
| 29 | PIR Motion Sensor | 1 |  |
| 30 | Analog Gas Sensor | 1 |  |
| 31 | ADXL345 Three Axis Acceleration Module | 1 |  |
| 32 | HC-SR04 Ultrasonic Sensor | 1 |  |
| 33 | DS3231 Clock Module | 1 |  |
| 34 | DHT11 Temperature and Humidity Sensor | 1 |  |
| 35 | Soil Humidity sensor | 1 |  |
| 36 | RC522 RFID Module | 1 |  |
| 37 | RFID Card | 1 |  |
| 38 | Access Key | 1 |  |
| 39 | RPI GPIO Shield | 1 |  |
| 40 | Pin Headers | 40 |  |
| 41 | 830-hole Breadboard | 1 |  |
| 42 | Female to Female Dupont Wire | 20 |  |
| 43 | Male to Female Dupont Wire | 20 |  |
| 44 | breadboard Jumper Wire | 30 |  |
| 45 | 40 pin Colorful Jumper Wire | 1 |  |
Kit Contents
Lesson 1: Hello World Lesson 2: LED Blinking Lesson 3: Breathing LED Lesson 4: Traffic Light Lesson 5: LED Chasing Effect Lesson 6: Button-controlled LED Lesson 7: Passive Buzzer Lesson 8: Active Buzzer Lesson 9: Responder Lesson 10: Flame Sensor Lesson 11: Ball Tilt Sensor Lesson 12: IR Remote Control Lesson 13: 1-digit LED Segment Display Lesson 14: 74HC595 Lesson 15: 4-digit LED Segment Display Lesson 16: LED Matrix Display Lesson 17: 1602 LCD Lesson 18: RGB LED Lesson 19: 9g Servo Control Lesson 20: ULN2003 Stepper Motor Lesson 21: Photo Resistor Lesson 22: LM35 Temp Sensor Lesson 23: pcf8591 Lesson 24: PIR Motion Sensor Lesson 25: MQ-2 Analog Gas Sensor Lesson 26: ADXL345 Acceleration Module Lesson 27: Ultrasonic Sensor Lesson 28: Joystick Module Lesson 29: 5V Relay Lesson 30: DHT11 Temp and Humidity Sensor Lesson 31: Soil Humidity Sensor Lesson 32: DS3231 Clock Module
System Programming & Corresponding Tool Library Installation
1. Format the TFT card:
a. Plug the TFT card into the USB port through the card reader, open and install the SDFormatter tool in tool folders we provided. Open the tool as the figure shown below:
Tool Website: https://www.sdcard.org/downloads/formatter_4/index.html
b. The Driver in the upper figure: G is the TFT card just inserted. If you have several other TFT cards inserted in the computer, you can pass the drop-down menu to select the TFT card that needs to be formatted. And then click "Format",it will automatically format the TFT card. The formatting process will pop up the warning as shown below, then click OK.
c. The picture below shows the successful format of the TFT card:
2. Program Raspberry Mirror Image:
a. Open the Win32DiskImager in tool folder we provided, open the tool as the following figure shown:
b. Click marked 1 to select the formatted TFT card, then click marked 2 to choose the system image file "2017-01-11-raspbian-jessie-lite" in the raspberry image folder we provided. The figure shown as below:
Raspberry Pi Download Address：https://www.raspberrypi.org/downloads/
c. The above steps are configured well and click “Write”, it will automatically program the raspberry mirror image to the TFT card, and you need to wait for a few minutes in this process. Below shows the Write Successful. Then click “OK “ to unplug the TFT card.
Log into Raspberry
1. Log into Raspberry via SSH
a. Insert TFT card burning well the system into Raspberry board. Internet interface of the motherboard is connected to LAN via the network cable, and the mini USB port on the motherboard is powered by an external power supply.
Then, use Advanced IP Scanner software，click 
，find the corresponding IP address of the raspberry pi, as shown below:
When logging in by SSH, you first need to put an ssh file in the system root directory, as shown below:
b. Open the PUTTY tool in the folder tool, only set two places of red circle as the figure shown below, the other places not to be set, and then click "Open" to log in.
Username for the initial login in Raspberry system: pi
Password: raspberry
Logging in Raspberry system for the first time, it is best to expand the root partition to the entire TFT card, then on the terminal please input: sudo raspi-config
It will appear the following window after execution:
Then, select 1 Expand Filesystem through the keyboard’s "↑↓"key, and click “Enter” key on the keyboard. Then through the "→ ←"key to select “Finish”, and click the “Enter” key on the keyboard. Finally, pop up the following window, then click “Yes”.
After click Yes, it has rebooted the Raspberry, so you just need to re-login it.
2. Using WinSCP to transfer file between PC host and Raspberry
a. Plug the network cable of the router into the Raspberry motherboard, and network cable must belong to the same network segment with the computer.
Then input ifconfig command in the terminal to check the Raspberry’s IP, and the IP at this moment is 192.168.1.121 as shown in the following figure:
b. Open the folder tool where provides a WinSCP installation package, then install and open the application program, the window interface shown as the figure below:
c. File protocol is SCP; Host name is Raspberry’s IP address; Default port number is 22; Username is pi; Password is raspberry.
Then click “Login”, if the login process appears prompts, click “Yes”. Appearing the below figure means successfully log in WinSCP.
3. Install Wiringpi
a. Wiringpi is a library file for raspberry to control IO port, in which integrates I2C library, SPI library, UART library, software PWM library and more.
The relevant library function folder provides the compression package of wiringpi library file.
Or you can download it on the official website: https://projects.drogon.net/raspberry-pi/wiringpi/download-and-install/
Use winSCP to put the wiringPi-b0a60c3.tar of PC into the pi user folder of raspberry system, as shown in the figure below:
b. In the terminal input cd/home/pi to enter pi folder; execute tar-xzf wiringPi-b0a60c3.tar.gz to unzip the file, getting wiringPi-b0a60c3 folder; in the terminal input cd wiringPi-b0a60c3 command, execute ./build to install wiringpi. The window interface below shows the successful installation:
c. To see whether the wiringpi installation is successful, in the terminal execute gpio readall command.
Pop up the below window interface means installation successfully.
Learning Courses
Documents
File:
https://drive.google.com/open?id=1309GFYVPZwPOBOqR1904CCM0fNGei9kD
Download Link of Mirror Image File:
https://www.raspberrypi.org/downloads/raspbian/