Search results
Jump to navigation
Jump to search
- ...ds to work with Keyestudio nano ch340 . It can be used as driver expansion board for engraving machines. It has in total 3 channel slots for A4988 stepper m keyestudio nano ch340 controller is a small, complete board based on the ATmega328. It’s a open source Simple I/O platform with 12 Di14 KB (2,193 words) - 10:29, 28 April 2021
- ...uits, suitable for a variety of development boards and controllers such as Arduino controller, STC single-chip microcomputer, AVR single-chip microcomputer, e ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d4 KB (574 words) - 15:57, 7 January 2021
- sensors/modules, the Raspberry Pi Pico board, the Raspberry Pi Pico expansion board and Dupont wires. <br> ...the Raspberry Pi Pico shield. You only need to stack the Raspberry Pi Pico board onto the Raspberry Pi Pico shield, and hook up them with Dupont wires, whic5 KB (638 words) - 14:02, 31 December 2021
- ...rface to communicate. When using it, directly stack it onto UNO R3 control board. ...tp://wiki.keyestudio.com/index.php/Ks0001_keyestudio_UNO_R3_BOARD UNO R3 board ]. <br>5 KB (772 words) - 14:24, 6 January 2021
- You can refer to the following connection. For UNO board and pressure sensor, connect the S pin of sensor to A0, negative pin to GND ...://wiki.keyestudio.com/index.php/Download_Arduino_IDE_and_Install_Driver Arduino IDE ].3 KB (364 words) - 12:18, 7 January 2021
- ...ed out as Registered Jack, allowing you to connect it to EASY plug Control board V2.0 for communication with only an RJ11 cable. <br> ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d5 KB (763 words) - 08:54, 8 January 2021
- You can download different version of Arduino IDE from the link here:<br> https://www.arduino.cc/en/Main/OldSoftwareReleases#1.5.x <br>6 KB (793 words) - 11:58, 4 March 2021
- ...UNO_R3_BOARD UNO R3 ]. So you just need to stack it onto UNO R3 control board when using. <br> To easily debug the operating mode of stepper motor driver board, there are 3 jumper caps under each pin slots. You can set the working mode5 KB (692 words) - 10:40, 29 April 2021
- ...UNO_R3_BOARD UNO R3 ]. So you just need to stack it onto UNO R3 control board when using. <br> To easily debug the operating mode of stepper motor driver board, there are 3 jumper caps under each pin slots. You can set the working mode5 KB (700 words) - 13:31, 14 August 2018
- You can connect the module to control board for communication using jumper wires.<br> ...g the code, do remember to place the Matrix library folder into directory \Arduino\libraries. Otherwise, fail to compile the code. <br>4 KB (599 words) - 10:05, 8 January 2021
- This is an Arduino servo driver shield. It has a PS2 interface for using a PS2 handle control. Stack the driver board onto the control board, wire up and upload the code. Four servos rotate from 0° to 180°, then fr2 KB (280 words) - 13:55, 23 May 2022
- This module should be used together with EASY plug control board. ...plug Control Board with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has d4 KB (716 words) - 17:04, 7 January 2021
- Ks0286 keyestudio CNC Kit / CNC Shield V3.0 +keyestudio Uno R3+4pcs DRV8825 Driver / GRBL CompatibleKeyestudio CNC Shield V3.0 can be used as driver expansion board for engraving machines. <br> * GRBL 0.8c compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)10 KB (1,531 words) - 09:32, 5 March 2021
- ...honeycomb hall magnetic sensor is fully compatible with micro bit control board. In the experiment, we connect it with the micro: bit by a crocodile clip. During the test, we test the analog value of S end via micro: bit control board. The analog value read is decreasing fast when the nearby magnetic field is2 KB (313 words) - 10:53, 22 January 2021
- ...quired. We particularly design this driver board compatible UNO R3 control board. * 1.Design in stacked style, only need to stack on UNO R3 control board which save space and facilitate to connect.<br>5 KB (676 words) - 11:24, 22 January 2021
- For each project, we offer you two programming language: Arduino C and graphical programming on the basis of KidsBlock Desktop, which is ben ...ions:''' Nano or ESP32 development board are both available as the control board; 15 sensors are integrated; The VCC of 3.3V/5V can be adjusted via DIP swit3 KB (477 words) - 13:59, 19 May 2023
- [[image:KS0341.jpg|thumb|500px|right|Keyestudio UNO Compatible Board Advanced ]] ....com/index.php/Ks0001_keyestudio_UNO_R3_BOARD keyestudio UNO R3 board] and ARDUINO UNO REV3. <br>20 KB (3,148 words) - 08:08, 30 April 2021
- [[image:0341.jpg|thumb|500px|right|Keyestudio REV4 Compatible Board Advanced ]] ...io.com/index.php/Ks0001_keyestudio_UNO_R3_BOARD keyestudio REV3 board] and ARDUINO UNO. <br>20 KB (3,182 words) - 13:56, 30 April 2021
- ...h the Arduino development platform, the Micro control board belongs to the Arduino series microcontroller. ...nd Micro control board, we will provide some learning courses based on the Arduino, like wiring methods, test code, etc.14 KB (2,023 words) - 15:44, 6 May 2020
- ...GSM/GPRS shield is based on Quad-Band SIM900 GSM/GPRS module. It provides Arduino with GSM/GPRS function. <br> ...DBG-Port, you can connect the port to Arduino or connect the port to PC by Arduino to proceed the debugging. <br>7 KB (1,084 words) - 15:11, 6 January 2021