KS4009(4010) 45 in 1 Sensor Starter Kit For BBC Micro:bit

Keyestudio 45 in 1 Starter Kit for BBC micro:bit

Introduction

micro: bit is a powerful hand-held, fully programmable, computer designed by the BBC. It is only half size of a credit card, available for children’s programming education. Onboard comes with Bluetooth, accelerometer, compass, three buttons, 5x5 LED matrix, USB interface, connection pins. In order to learn micro bit more easier, we particularly make this kit, in which includes a keyestudio sensor shield fully compatible with micro bit and other commonly used sensor modules. In addition, this sensor kit also provides various learning projects for you, including wiring diagram, source code and more. It can help you make learning easy and fun to enjoy the programming.

Kit List

Note: The micro:bit main board is Not Included in KS4009 starter kit, but Included in KS4010 starter kit.

KS4010

No.	Product Name	Quantity
0	No micro：bit Board in KS4009 Kit
0	With micro:bit board in KS4010 Kit	1
1	Micro bit Sensor Shield V2	1
2	Digital White LED Module	1
3	Red LED Module	1
4	3W LED Module	1
5	keyestudio RGB LED Module	1
6	keyestudio Analog Temperature Sensor	1
7	keyestudio Photocell Sensor	1
8	keyestudio Analog Sound Sensor	1
9	Analog Rotation Sensor	1
10	keyestudio Passive Buzzer module	1
11	keyestudio Digital Buzzer Module	1
12	keyestudio Digital Push Button	1
13	keyestudio Digital Tilt Sensor	1
14	keyestudio Photo Interrupter Module	1
15	Capacitive Touch Sensor	1
16	Traffic Light Module	1
17	Hall Magnetic Sensor	1
18	Line Tracking Sensor	1
19	Infrared Obstacle Detector Sensor	1
20	PIR Motion Sensor	1
21	Flame Sensor	1
22	Crash Sensor	1
23	Analog Gas Sensor	1
24	Analog Alcohol Sensor	1
25	Reed Switch Module	1
26	keyestudio Water Sensor	1
27	Soil Humidity Sensor	1
28	LM35 Linear Temperature Sensor	1
29	Vibration Sensor	1
30	Thin-film Pressure Sensor	1
31	GUVA-S12SD 3528 Ultraviolet Sensor	1
32	1602 I2C Module	1
33	TEMT6000 Ambient Light Sensor	1
34	HC-SR04 Ultrasonic Module	1
35	Joystick Module	1
36	Micro Servo	1
37	Single Relay Module	1
38	Steam Sensor	1
39	F-F Dupont Jumper Wire 40pin	1
40	USB Cable	1
41	Premium Battery Case 6-cell AA	1
42	Keyestudio Knock Sensor Module	1
43	Keyestudio Digital IR Receiver Module	1
44	Keyestudio Magic Light Cup Sensor	1
45	Keyestudio 0.96inch OLED Module	1
46	Keyestudio L9110 Fan Module	1
47	Keyestudio DHT11 Temperature and Humidity Sensor	1
48	Keyestudio 18B20 Temperature Sensor	1
49	Keyestudio IR Remote Control	1
50	Keyestudio BBC Micro bit Motherboard	1

micro:bit Pins

Before getting started with the following projects, first need to figure out each pin of micro:bit main board. Please refer to the reference diagram shown below.

The BBC micro:bit has 25 external connections on the edge connector of the board, which we refer to as ‘pins’. The edge connector is the grey area on the right side of the figure above. There are five large pins, that are also connected to holes in the board labelled: 0, 1, 2, 3V, and GND. And along the same edge, there are 20 small pins that you can use when plugging the BBC micro:bit into an edge connector.

Note that it read from the BBC micro:bit official website. More reference you can click the link below:
BBC micro bit Pins: http://microbit.org/guide/hardware/pins/
BBC micro:bit website: http://microbit.org/
Micro bit MakeCode Block Editor: https://makecode.microbit.org/
Meet micro:bit starter programming: http://microbit.org/guide/
BBC micro:bit Features Guide: http://microbit.org/guide/features/
BBC micro:bit Safety Warnings: http://microbit.org/guide/features/
BBC micro:bit Quick Start Guide: http://microbit.org/guide/quick/

After mastering the basic information of BBC micro:bit, in the following part let’s move on to programming projects. Use this small board with keyestudio micro bit sensor shield and other sensor modules to make some interactive experiments. Play it and learn it. Enjoy your wonderful time!

Installing Arduino Software

We will use the Arduino software in the following projects. First you should install the Arduino software and driver.
We usually use the Windows software Arduino 1.5.6 version. You can download it from the link below:
https://www.arduino.cc/en/Main/OldSoftwareReleases#1.5.x
Or you can browse the ARDUINO website to download the latest version from this link, https://www.arduino.cc, pop up the following interface.

Then click the SOFTWARE on the browse bar, you will have two options ONLINE TOOLS and DOWNLOADS.

Click DOWNLOADS, it will appear the latest software version of ARDUINO 1.8.5 shown as below.

In this software page, on the right side you can see the version of development software for different operating systems. You should download the software that is compatible with the operating system of your computer.
We will take WINDOWS system as an example here. There are also two options under Windows system, one is installed version, the other is non-installed version. For simple installed version, first click Windows Installer, you will get the following page.

This way you just need to click JUST DOWNLOAD, then click the downloaded file to install it.
For non-installed version, first click Windows ZIP file, you will also get the pop-up interface as the above figure.
Click JUST DOWNLOAD, and when the ZIP file is downloaded well to your computer, you can directly unzip the file and click the icon of ARDUINO software to start it.

Installing Arduino (Windows)

Install Arduino with the exe. Installation package downloaded well.

Click“I Agree”to see the following interface.

Click “Next”. Pop up the interface below.

You can press Browse… to choose an installation path or directly type in the directory you want.
Then click “Install” to initiate installation.

Wait for the installing process, if appear the interface of Window Security, just continue to click Install to finish the installation.

Installing Driver

The driver installation may have slight differences in different computer systems. So in the following let’s move on to the driver installation in the WIN 7 system.
The Arduino folder contains both the Arduino program itself and the drivers that allow the Arduino to be connected to your computer by a USB cable. Before we launch the Arduino software, you are going to install the USB drivers.

Plug one end of your USB cable into the Arduino and the other into a USB socket on your computer. When you connect UNO board to your computer at the first time, right click the icon of your “Computer” —>for “Properties”—> click the “Device manager”, under “Other Devices”, you should see an icon for “Unknown device” with a little yellow warning triangle next to it. This is your Arduino.

Then right-click on the device and select the top menu option (Update Driver Software...) shown as the figure below..

It will then be prompted to either “Search Automatically for updated driversoftware” or “Browse my computer for driver software”. Shown as below. In this page, select “Browse my computer for driver software”.

After that, select the option to browseand navigate to the “drivers” folder of Arduino installation.

Click “Next” and you may get a security warning, if so, allow the software to be installed. Shown as below.

Once the software has been installed, you will get a confirmation message. Installation completed, click “Close”.

Up to now, the driver is installed well. Then you can right click “Computer” —>“Properties”—>“Device manager”, you should see the device as the figure shown below.