KS(3001...3012)Assemble the Housing of Raspberry Pi 4: Difference between revisions
Keyestudio (talk | contribs) (Created blank page) |
Keyestudio (talk | contribs) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
== Preparations： == | |||
What you need: | |||
<br>[[File:图片13001-1.png|500px|frameless|thumb]]<br> | |||
== Detailed Steps == | |||
=== Stick Heat Sink === | |||
Take out three heat sinks and three thermal conductive adhesives.(figure 1) <br> | |||
Glue conductive adhesives on the heat sinks.(figure 2) <br> | |||
Then stick heat sinks to the Raspberry Pi 4.(figure 3) <br> | |||
<br>[[File:图片13001-2.png|500px|frameless|thumb]]<br> (figure 1) | |||
<br>[[File:QQ图片202108261632.png|500px|frameless|thumb]]<br> (figure 2) | |||
<br>[[File:图片13001-3.png|500px|frameless|thumb]]<br> (figure 3) | |||
=== Assemble a Fan === | |||
Fix the fan onto the housing with screws, as shown below; | |||
Note: refer to the figure 4 and make fan’s back upward. | |||
<br>[[File:图片13001-4.png|500px|frameless|thumb]]<br> | |||
<br>[[File:图片13001-5.png|500px|frameless|thumb]]<br> (figure 4) | |||
== Prepare the following parts we need == | |||
<br>[[File:图片13001-6.png|500px|frameless|thumb]]<br> | |||
Cover the Raspberry Pi 4 with the housing | |||
And place the oval plastic board as follows; | |||
Screw them together. (figure 7) | |||
<br>[[File:图片13001-7.png|500px|frameless|thumb]]<br> | |||
Don’t forget to screw the bottom.(figure 8) | |||
<br>[[File:图片13001-8.png|500px|frameless|thumb]]<br> | |||
== Paste Colloidal Particles == | |||
Then glue colloidal particles in the four grooves, as shown below; | |||
图 | |||
图 | |||
== Wire up == | |||
Respectively attach the red wire, black wire of the fan to 5V and GND of the Raspberry Pi, as shown below: | |||
Note: don’t reverse the negative and positive poles of the fan. | |||
<br>[[File:图片13001-11.png|500px|frameless|thumb]]<br> | |||
Latest revision as of 17:07, 26 August 2021
Preparations：
What you need:
Detailed Steps
Stick Heat Sink
Take out three heat sinks and three thermal conductive adhesives.(figure 1)
Glue conductive adhesives on the heat sinks.(figure 2)
Then stick heat sinks to the Raspberry Pi 4.(figure 3)
(figure 1)
(figure 2)
(figure 3)
Assemble a Fan
Fix the fan onto the housing with screws, as shown below; Note: refer to the figure 4 and make fan’s back upward.
(figure 4)
Prepare the following parts we need
Cover the Raspberry Pi 4 with the housing
And place the oval plastic board as follows;
Screw them together. (figure 7)
Don’t forget to screw the bottom.(figure 8)
Paste Colloidal Particles
Then glue colloidal particles in the four grooves, as shown below;
图 图
Wire up
Respectively attach the red wire, black wire of the fan to 5V and GND of the Raspberry Pi, as shown below: Note: don’t reverse the negative and positive poles of the fan.
