KS0349 Keyestudio 48 in 1 Sensor Kit: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 148: Line 148:


Step 3: Next to find out the “libraries” folder of this kit(seen in the link: https://fs.keyestudio.com/KS0349), you just need to replicate and paste it into the libraries folder of Arduino IDE.
Step 3: Next to find out the “libraries” folder of this kit(seen in the link: https://fs.keyestudio.com/KS0349), you just need to replicate and paste it into the libraries folder of Arduino IDE.


<br>[[File:0349=7.png|800px|frameless|thumb]]<br>
<br>[[File:0349=7.png|800px|frameless|thumb]]<br>
<br>[[File:0349=8.png|800px|frameless|thumb]]<br>
<br>[[File:0349=8.png|800px|frameless|thumb]]<br>
<br>[[File:0349=9.png|800px|frameless|thumb]]<br>
<br>[[File:0349=9.png|800px|frameless|thumb]]<br>
Then copy the above libraries in the libraries of Arduino, as shown below:
<br>[[File:0349=10.png|800px|frameless|thumb]]<br>
<br>[[File:0349=10.png|800px|frameless|thumb]]<br>


== Projects ==
== Projects ==

Revision as of 08:09, 19 November 2020

Description

This sensor kit contains 48 kinds of commonly used sensor modules in playing the microcontroller, such as active buzzer module, 5V relay module, temperature and humidity module and so on. It is compatible for various microcontrollers and Raspberry Pi. At the same time, we also provide some detailed projects for each sensor based on development board, including wiring method, test code, etc. It can help you have further understanding of those sensor modules and can apply them to interactive projects. Note that in the following projects, the main board and other wires are not included in this kit. You need to prepare them by yourself.

Component List


thumb

thumb

thumb

thumb

thumb

Install Arduino IDE and Driver

Download software

When we get control board, we need to download Arduino IDE and driver firstly. You could download Arduino IDE from the official website: https://www.arduino.cc/, click the SOFTWARE on the browse bar, click “DOWNLOADS” to enter download page, as shown below:


thumb

There are various versions for Arduino, just download a suitable version for your system, we will take WINDOWS system as an example to show you how to download and install.


thumb

There are two versions for WINDOWS system, one is installed version, another one is download version, you just need to download file to computer directly and unzip it. These two versions can be used normally. Choose one and download on your computer.


thumb

You just need to click JUST DOWNLOAD, then click the downloaded file to install it. And when the ZIP file is downloaded, you can directly unzip and start it.


We need to know keyestudio V4.0 development board, as a core of this smart car.


thumb

(1)Keyestudio V4.0 Development Board

keyestudio V4.0 development board is an Arduino uno-compatible board, which is based on ATmega328P MCU, and with a cp2102 Chip as a UART-to-USB converter.


thumb

It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz quartz crystal, a USB connection, a power jack, 2 ICSP headers and a reset button.


thumb

It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it via an external DC power jack (DC 7-12V) or via female headers Vin/ GND(DC 7-12V) to get started.


thumb


Install other visions of driver

If your development board is Arduino board, install the driver as follows: Step 1: Plug in the development board, click Computer----- Properties----- Device Manager, you could see the unknown device is shown.
thumb


Step 2: Update the driver
thumb

Step 3: click“browse my computer for updated driver software”


thumb

Step 4: find out the folder where the ARDUINO software is installed, click drivers folder and tap“Next”


thumb

Step 5: the driver is installed successfully.


thumb

The device manager shows the serial port of Arduino.
thumb

Arduino IDE Setting

Click0486-12.png icon,open Arduino IDE.
0085=14.png

To avoid the errors when uploading the program to the board, you need to select the correct Arduino board that matches the board connected to your computer. Then come back to the Arduino software, you should click Tools→Board, select the board. (as shown below)
0085=15.png


Then select the correct COM port (you can see the corresponding COM port after the driver is successfully installed)


0085=16.png

0085=17.png

Before uploading the program to the board, let’s demonstrate the function of each symbol in the Arduino IDE toolbar.

A- Used to verify whether there is any compiling mistakes or not.
B- Used to upload the sketch to your Arduino board.
C- Used to create shortcut window of a new sketch.
D- Used to directly open an example sketch.
E- Used to save the sketch.
F- Used to send the serial data received from board to the serial monitor.

Start your first program

Open the file to select Example, choose BLINK from BASIC, as shown below:



048610png.png


048611png.png

Set board and COM port, the corresponding board and COM port are shown on the lower right of IDE.


048612png.png

Click 0486-20.png to start compiling the program, check errors.


048613png.png

Click 0486-23.pngto upload the program, upload successfully.


048614png.png

Upload the program successfully, the onboard LED lights on for 1s, lights off for 1s. Congratulation, you finish the first program.


Add project Libraries

What are Libraries ?

Libraries are a collection of code that makes it easy for you to connect to a sensor,display, module, etc.
For example, the built-in LiquidCrystal library helps talk to LCD displays. There are hundreds of additional libraries available on the Internet for download.
The built-in libraries and some of these additional libraries are listed in the reference.

How to Install a Library ?

Here we will introduce the most simple way for you to add libraries.
Step 1:After downloading well the Arduino IDE, you can right-click the icon of Arduino IDE.
Find the option "Open file location" shown as below:


thumb

Step 2: Enter it to find out libraries folder which is the library file of Arduino.


thumb

Step 3: Next to find out the “libraries” folder of this kit(seen in the link: https://fs.keyestudio.com/KS0349), you just need to replicate and paste it into the libraries folder of Arduino IDE.


thumb

thumb

thumb

thumb

Projects