KS0372 EASY plug Servo Module +Micro Servo

From Keyestudio Wiki
Revision as of 17:07, 8 May 2019 by Keyestudio (talk | contribs)
Jump to navigation Jump to search
EASY plug Servo Module + Micro Servo


Introduction

If you want to use the Micro Servo and EASY PLUG control board to make experiments, you need to use the EASY plug Servo extension module.
Here comes EASY plug Servo module and a 180° Micro Servo together in the package.

Package Includes

  • EASY plug Servo Module *1
  • Micro Servo *1


The EASY plug Servo module is extended into Registered Jack, so you can connect it to EASY PLUG control board using only a RJ11 cable.
The Servo module also comes with 3pins of 2.54mm pin pitch, fully compatible with servo pins.

EASY plug Servo Module


Servo motor comes with many specifications. But all of them have three connection wires, distinguished by brown, red, orange colors. Brown one is for ground, red one for power positive, orange one for signal line.

Micro Servo

Included with your Micro Servo you will find a variety of white motor mounts that connect to the shaft of your servo. You may choose to attach any mount you wish for the circuit. It will serve as a visual aid, making it easier to see the servo spin.
The rotation angle of Servo motor is controlled by regulating the duty cycle of PWM (Pulse-Width Modulation) signal. The standard cycle of PWM signal is 20ms (50Hz).
Theoretically, the width is distributed between 1ms-2ms, but in fact, it’s between 0.5ms -2.5ms. The width corresponds to the rotation angle from 0° to 180°.

thumb


Micro Servo Parameters

  • Operating voltage: DC 4.8V〜6V
  • Angle range: about 180°(in 500→2500μsec)
  • Pulsewidth range: 500→2500μsec
  • No-load speed: 0.12±0.01 sec/60(DC 4.8V); 0.1±0.01 sec/60(DC 6V)
  • No-load current: 200±20mA(DC 4.8V); 220±20mA(DC 6V)
  • Stop torque: 1.3±0.01kg/cm(DC 4.8V); 1.5±0.1kg/cm(DC 6V)
  • Stop current: ≦850mA(DC 4.8V); ≦1000mA(DC 6V)
  • Standby current: 3±1mA(DC 4.8V); 4±1mA(DC 6V)
  • Operation temperature: -10℃〜50℃
  • Save temperature: -20℃〜60℃
  • Motor wire length: 250 ± 5 mm


Connect It Up

Connect the EASY Plug servo module and micro servo to control board using an RJ11 cable.
Connect the servo motor to EASY Plug Servo module. Brown line is for ground, red one for V pin, orange one for signal pin.
Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See


thumb

After uploading the code, open the serial monitor, enter the number 1 to 9, and click Send, it will control the servo motor rotate at a certain angle.
thumb

thumb


Rotating back and forth

Complete the above project, you can also upload the code below to control the servo motor rotating back and forth at a certain angle.

Test Code:

thumb



Resources

Download the Arduino Code and PDF:
https://drive.google.com/open?id=1bHXCkYVAKkyWzqVm-njHSh3Ijw2al3do

Download the Mixly Code and PDF:
https://drive.google.com/open?id=1kF1zDDRj5mnB9MkB14fDC-KD72EnayyQ


Buy from