KS0373 EASY plug Slide Potentiometer: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
 
(4 intermediate revisions by the same user not shown)
Line 15: Line 15:
==Parameters==
==Parameters==
* Operating Voltage: DC 3.3V-5V
* Operating Voltage: DC 3.3V-5V
* Resistance: 10K
* Resistance: 5K
* Port: analog quantity
* Port: analog quantity
* Property: ROHS
* Property: ROHS
Line 32: Line 32:
==Upload the Code==
==Upload the Code==
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
Below is an example code. Open or drag below code to [https://wiki.keyestudio.com/Getting_Started_with_Mixly  Mixly Blocks] and upload. <br>
<br>[[File:0373-2.png|500px|frameless|thumb]]<br>
<br>[[File:0373-2.png|600px|frameless|thumb]]<br>


<br>
<br>
==What You Should See==
==What You Should See==
<br>[[File:KS0373-3.png|500px|frameless|thumb]]<br>
<br>[[File:KS0373-3.png|600px|frameless|thumb]]<br>
<br>
<br>
After uploading the code, open the serial monitor and set the baud rate to 9600; <br>
After uploading the code, open the serial monitor and set the baud rate to 9600; <br>
you should be able to see the analog value of analog pin A6,A7. If slide the slider, the value will change.  
you should be able to see the analog value of analog pin A6,A7. If slide the slider, the value will change.  
<br>[[File:KS0373-4.png|500px|frameless|thumb]]<br>
<br>[[File:KS0373-4.png|600px|frameless|thumb]]<br>


<br>
<br>
==Controlling LED Brightness==
==Controlling LED Brightness==
Except from reading the analog value of slide potentiometer, you are able to use the slide potentiometer to control the brightness of LED.
Except from reading the analog value of slide potentiometer, you are able to use the slide potentiometer to control the brightness of LED.
Line 59: Line 61:
<br>
<br>


<br>
==Controlling Servo Angle==
==Controlling Servo Angle==


'''Hookup Guide'''<br>
'''Hookup Guide'''<br>
<br>[[File:KS0373-8.png|500px|frameless|thumb]]<br>
<br>[[File:KS0373-8.png|600px|frameless|thumb]]<br>


<br>  
<br>  
Line 77: Line 80:


==Resources ==
==Resources ==
'''Download the Arduino Code and PDF:'''<br>
https://drive.google.com/open?id=1zbdjlPfSHBYk4Ae13_jN_dALxI5-LPIi
'''Download the Mixly Code and Datasheet:'''<br>
https://drive.google.com/open?id=1P3ktlTE2OxDgnfScaCHHkTiFgty4NKT5


'''Download the Mixly Easy plug library:'''<br>
https://fs.keyestudio.com/KS0373
https://wiki.keyestudio.com/How_to_Import_Mixly_Library


<br>
<br>

Latest revision as of 08:47, 8 January 2021

EASY plug Slide Potentiometer

Introduction

The EASY plug slide potentiometer uses high-quality sliding appliances for stable and reliable performance. It is a dual analog output that outputs a 0-VCC analog voltage signal.
The module pins are extended into Registered jack, so you can easily connect it to EASY Plug control board using a RJ11 cable.
There are 6 pad interfaces on the module. So you can solder two 3pin headers with a pitch of 2.54mm on the module.
It can be used to connect with other MCUs. The signal terminal outputs two analog values. The sum of the two analog values is 1023.
This module should be used together with EASY plug control board.

Special Note:
The sensor/module is equipped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equipped with the RJ11 6P6C interface but has different internal line sequence, can’t be used compatibly with our sensor/module.


Parameters

  • Operating Voltage: DC 3.3V-5V
  • Resistance: 5K
  • Port: analog quantity
  • Property: ROHS


Technical Details

  • Dimensions: 28mm*76.7mm*31.3mm
  • Weight: 17g


Connect It Up

Connect the EASY Plug Slide Potentiometer to control board using an RJ11 cable. Then connect the control board to your PC with a USB cable.
thumb


Upload the Code

Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See


thumb

After uploading the code, open the serial monitor and set the baud rate to 9600;
you should be able to see the analog value of analog pin A6,A7. If slide the slider, the value will change.
thumb


Controlling LED Brightness

Except from reading the analog value of slide potentiometer, you are able to use the slide potentiometer to control the brightness of LED.
Hookup Guide

thumb


Test Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See
After uploading the code, slide the potentiometer, the brightness of LED will change.


Controlling Servo Angle

Hookup Guide

thumb


Test Code
Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See
After uploading the code, slide the potentiometer, the servo motor will rotate to a certain angle.



Resources

https://fs.keyestudio.com/KS0373


Buy from