KS0486 Keyestudio PLUS Development Board (Black And Eco-friendly)

From Keyestudio Wiki
Jump to navigation Jump to search


0486-1 - 副本.png




Description

Doing experiment for electronic products, we often program on the Arduino IDE development environment by arduino series microcontrollers.
Keyestudio PLUS control board is fully compatible with Arduino IDE development environment. It contains all the functions of the Arduino UNO R3 board. Moreover, some improvements we made highly strengthen its function(as shown below). In order to wire efficiently, we equip with a 1m USB cable of type-c interface for you.


04861.png

Specifications


0486.1png.png


  • USB to serial chip: CP2102
  • Working voltage: 5V or 3.3V (DIP switch control)
  • External power: DC 6-15V (recommend 9V)
  • Digital I / O pins: 14 (D0-D13)
  • PWM channel: 6 (D3 D5 D6 D9 D10 D11)
  • Analog input channel (ADC): 8 (A0-A7)
  • Each I / O Port of DC output capability : 20 mA
  • Output capability of 3.3V port: 50 mA
  • Flash Memory: 32 KB (of which 0.5 KB is used by the bootloader)
  • SRAM: 2 KB (ATMEGA328P-AU)
  • EEPROM: 1 KB (ATMEGA328P-AU)
  • Clock speed: 16MHz
  • On-board LED pin: D13


  • Serial communication interface: D0 is RX, D1 is TX
  • PWM interface (pulse width modulation): D3 D5 D6 D9 D10 D11
  • External interrupt interface: D2 (interrupt 0) and D3 (interrupt 1)
  • SPI communication interface: D10 is SS, D11 is MOSI, D12 is MISO, D13 is SCK
  • IIC communication port: A4 is SDA, A5 is SCL

Instruction

Programming the control board, we need to download Arduino IDE.
You could download from the official website: https://www.arduino.cc/en/Main/OldSoftwareReleases#1.5.x.
There are various versions of the IDE in the official link, here we download a Windows system, version 1.5.6.


0486.2png.png


Installing Arduino IDE

Double click arduino-1.5.6-r2-windows to start. Select “I Agree”to accept license agreement.


0486.3png.png
Select components to install and click “Next”.

0486-2.png
Click “Browse” and select another folder. Click “Install” to start the installation.

0486-3.png
Finally, wait for a few minutes to finish.


0486-4.png

0486-5.png


4.2 Installing Driver

The corresponding driver is needed when using Arduino IDE. Its USB serial chip is CP2102. There are drivers of all edition systems in the link below.
https://www.silabs.com/products/development-tools/software/usb-to-uart-bridge-vcp-drivers

You can refer to the link below:
https://v.qq.com/x/page/s0367yegedj.html
Next, we introduce the driver installation method of Windows systems. Open the driver file, as shown below.


0486-6.png
Click 0486-7.png click “next step”, as shown below:

0486-8.png
Click “next step”, as shown below:
0486-9.png
Installing successfully, click “complete” to end installation, as shown below.

0486-10.png
Right click computer ---> Properties ---> ---> Device Manager, then the corresponding COM port is shown. (as shown below)
0486-11.png

Arduino IDE Setting

Click0486-12.png icon,open Arduino IDE.
0486-13.png

To avoid the errors when uploading the program to the board, you need to select the correct Arduino board that matches the board connected to your computer. Then come back to the Arduino software, you should click Tools→Board, select the board. (as shown below)
0486-14.png


Then select the correct COM port (you can see the corresponding COM port after the driver is successfully installed)


0486-11.png

0486-16.png

Before uploading the program to the board, let’s demonstrate the function of each symbol in the Arduino IDE toolbar.



0486-17.png

A- Used to verify whether there is any compiling mistakes or not.
B- Used to upload the sketch to your Arduino board.
C- Used to create shortcut window of a new sketch.
D- Used to directly open an example sketch.
E- Used to save the sketch.
F- Used to send the serial data received from board to the serial monitor.

4.4 Hello World!

Copy the following code on the Arduino IDE

int val; 
int ledpin=13; 
void setup()
{
Serial.begin(9600); 
pinMode(ledpin,OUTPUT);
}
void loop()
{
val=Serial.read();
if(val=='R')
{
digitalWrite(ledpin,HIGH);
delay(500);
digitalWrite(ledpin,LOW);
delay(500);
Serial.println("Hello World!");
}
}



0486-18.png

Set the board and COM port, the corresponding board and COM port are displayed in the lower right corner of the IDE.
0486-19.png

Click 0486-20.pngicon to start compiling the program.
0486-21.png

0486-22.png

Click0486-23.png icon to start upload the program, upload successfully.
0486-24.png

0486-25.png

Click0486-26.pngto open serial monitor, set baud rate to 9600, enter “R” character, click “Send” (RX light will flash once when computer sends a “R” character to control board),then D13 indicator on the control board blinks once, "Hello World!" is shown on the serial monitor( control board sends "Hello World!" to the computer, TX light flashes once)
0486-27.png

Resource

Get One Now