KS0502 Keyestudio MEGA 2560 PRO Development Board(Black and Eco-friendly)

From Keyestudio Wiki
Jump to navigation Jump to search


0502-1.png

Introduction

The mega 2560 control board, among the series of MCUs , is the most popular since it has numerous pins. However, a substantial of pins don’t meet the space demand of DIY design. To tackle this issue, we roll out the Keyestudio MEGA 2560 PRO development board. In fact, its use method is as same as the official mega board, in addition to the different volume.

Its processor core is ATMEGA2560-16AU. In the meantime, it has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 channel serial communication ports, a USB connection, 1 ICSP header, and a reset button. And all ports are extended by pins with the interval of 2.54mm. What’s more, you can burn the firmware for ATMEGA2560-16AU through the built-in ICSP port. Luckily, the firmware of this chip is burnt well before delivery, therefore, you don’t need to burn firmware.

The power can be supplied through USB cable, port 5V, GND(DC 5V), as well as Vin GND(DC 7-12V).

Specification

  • Microcontroller: ATMEGA2560-16AU
  • USB to serial chip:CH340G
  • Operating Voltage: 5V
  • Input Voltage (recommended):DC 7-12V
  • Digital I/O Pins: 54 (D0-D53)
  • PWM Digital I/O Pins:15(D2-D13 D44-D46)
  • Analog Input Pins: 16(A0-A15)
  • DC Current per I/O Pin: 20 mA
  • DC Current for 3.3V Pin: 50 mA
  • Flash Memory: 256 KB of which 8 KB used by bootloader
  • SRAM: 8 KB
  • EEPROM: 4 KB
  • Clock Speed: 16 MHz
  • LED_BUILTIN:D13


Pin Interfaces:


0502-2.png


1 External Power Ports External input: DC 7-12V
2 Ground GND
3 LED indicator(TX) 5V
4 3.3V Provide DC 3.3V output voltage
5 AREF Analog reference. Used to set the external reference voltage(0-5V)
6 Reset Button Port
Can be connected to press button, as same as reset button
7 Serial communication port The default serial communication port,

RX responds to D0(digital port), TX responds to D1(digital port)

8 Digital Ports Have 54 digital input/output pins (of which 15 can be used as PWM outputs). These pins can be configured as digital input pin to read the logic value (0 or 1). Or used as digital output pin to drive different modules like LED, relay, etc.
9 Analog Ports 16 analog pins (A0-A15)
10 ATMEGA2560(Microcontroller) Each board has its own microcontroller.

The MCU of this board is ATMEGA2560-16AU.

11 ICSP Pin the AVR, an Arduino micro-program header consisting of MOSI, MISO, SCK, RESET, VCC, and GND.

It is often called the SPI (serial peripheral interface) and can be considered an "extension" of the output. In fact, slave the output devices to the SPI bus host.When connecting to PC, program the firmware to ATMEGA2560-16AU.

12 L Indicator When D13 is high level, LED will be on; when it is low level, LED will be off
13 ON Indicator LED is on when control board is plugged in power, otherwise, it will be off
14 TX Indicator When Arduino board communicates via serial port and sends the message, TX led will flash
15 RX Indicator When Arduino board communicates via serial port and receive the message, RX led will flash.
16 Reset Button Used to reset the control board
17 Micro USB Supply power for control board and upload code
18 USB to serial chip CH340G, transform USB signals of computer to serial signals

Specialized Functions of Some Pins:

Serial Communication Port(4-channel):Serial(D0 corresponds to RX0, D1 is equivalent to TX0), Serial1(D19 corresponds RX1, D18 is equivalent to TX1), Serial2 (D17 corresponds to RX2, D16 stands for TX2) and Serial3(D15 stands for RX3, D14 corresponds to TX3). RX(D0)and TX(D1)are connected to the USB to serial chip of CH340G.

  • Serial Communication: D0 (RX0) and D1 (TX1); Serial 1: D19 (RX1) and D18 (TX1); Serial 2: D17 (RX2) and D16 (TX2); Serial 3: D15 (RX3) and D14 (TX3).
  • PWM Pins (Pulse-Width Modulation): D2 to D13, and D44 to D46.
  • External Interrupts: D2 (interrupt 0), D3 (interrupt 1), D18 (interrupt 5), D19 (interrupt 4), D20 (interrupt 3), and D21 (interrupt 2).
  • SPI communication: D53 (SS), D52 (SCK), D51 (MOSI), D50 (MISO).
  • IIC communication: D20 (SDA); D21 (SCL).

Windows System

Download Arduino IDE

When getting this control board, we need to install Arduino IDE Enter the website https://www.arduino.cc/
And click SOFTWARE,then click DOWNLOADS


thumb

You can select the latest version-----1.8.13. Alternatively, the previous release is your another choice. In this project, we use 1.8.12 version.


thumb

Clickthumbto enter the new page. As shown below; The Windows installer needs installing manually. Yet , the Windows zip file for non admin install,a zip file of Arduino 1.8.12 version, can be directly downloaded and installed.


thumb

Install Driver

For this part, we need to install the driver of Arduino IDE First, let’s attach USB cable to computer. The driver can be installed automatically if the PC system is Windows 10, however, you need to install the driver manually if the PC system is other version. The USB to serial chip of control board is CH340G, therefore, we will install its driver(usb_ch341_3.1.2009.06).

Click Computer----- Properties----- Device Manager, as shown below:


thumb

Clickthumband“Update Driver Program”


thumb

Jump into the following page and select“Browse my computer for driver software”.


thumb

Search the usb_ch341_3.1.2009.06 folder


thumb

After the driver is installed, you need to click Close.


thumb

Click Computer----- Properties----- Device Manager, as shown below


thumb

Arduino IDE Setting

Clickthumbicon to pen Arduino IDE.


thumb


When downloading the sketch to the board, you must select the correct name of Arduino board that matches the board connected to your computer. As shown below;


thumb


Then select the correct COM port (you can see the corresponding COM port after the driver is successfully installed).


thumb


thumb


thumb

A- Used to verify whether there is any compiling mistakes or not.
B- Used to upload the sketch to your Arduino board.
C- Used to create shortcut window of a new sketch.
D- Used to directly open an example sketch.
E- Used to save the sketch.
F- Used to send the serial data received from board to the serial monitor.

Start A Program

Resources

Download the PDF:

https://fs.keyestudio.com/KS0502