KS0507 Keyestudio Smart RV Kit: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(188 intermediate revisions by the same user not shown)
Line 215: Line 215:


<br>[[Image:0507--34.png|400px|frameless]]<br>
<br>[[Image:0507--34.png|400px|frameless]]<br>


== Projects ==
== Projects ==
Line 332: Line 331:
If output five hundred 1, that is 5V; if all of which is 1, that is 0V. If output 010101010101 in this way then the output port is 2.5V, which is like showing movie. The movie we watch are not completely continuous. It actually outputs 25 pictures per second. In this case, the human can’t tell it, neither does PWM. If want different voltage, need to control the ratio of 0 and 1. The more 0,1 signals output per unit time, the more accurately control.<br>
If output five hundred 1, that is 5V; if all of which is 1, that is 0V. If output 010101010101 in this way then the output port is 2.5V, which is like showing movie. The movie we watch are not completely continuous. It actually outputs 25 pictures per second. In this case, the human can’t tell it, neither does PWM. If want different voltage, need to control the ratio of 0 and 1. The more 0,1 signals output per unit time, the more accurately control.<br>
(2)Component:<br>
(2)Component:<br>
<br>[[File:0507--9.png|500px|frameless|thumb]]<br>
<br>[[File:QQ图片20210901132133.png|500px|frameless|thumb]]<br>
(3)Connection Diagram:<br>
(3)Connection Diagram:<br>
We keep connection diagram unchanged.<br>
We keep connection diagram unchanged.<br>
<br>[[File:0507--10.png|500px|frameless|thumb]]<br>
<br>[[File:QQ图片20210901132135.png|500px|frameless|thumb]]<br>
(4)Test Code:<br>
(4)Test Code:<br>
<pre>
<pre>
Line 433: Line 432:


(1)Description:
(1)Description:
In this project, we control LED brightness by button module. The low level(0) is output when the button is pressed; however, high level(1) is output when button is released.
In this project, we control LED brightness by button module. The low level(0) is output when the button is pressed; however, high level(1) is output when button is released.


Line 446: Line 446:
(3)Component:
(3)Component:


<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补1.png|500px|frameless|thumb]]<br>


(4)Connection Diagram:<br>
(4)Connection Diagram:<br>
Line 476: Line 476:


(6)Test Result:<br>
(6)Test Result:<br>
Upload code, open serial monitor to set baud rate to 9600. The number “1”shows up then“0”appears on the monitor.<br>
Upload code, open serial monitor to set baud rate to 9600. The number “1” shows up then “0” appears on the monitor.<br>


<br>[[File:0507--14.png|500px|frameless|thumb]]<br>
<br>[[File:0507--14.png|500px|frameless|thumb]]<br>
Line 540: Line 540:
<span style=color:red>Note: Adjust the sensitivity by rotating the potentiometer before the test. The sensitivity is best when LED is at on and off state.</span><br>
<span style=color:red>Note: Adjust the sensitivity by rotating the potentiometer before the test. The sensitivity is best when LED is at on and off state.</span><br>
(3) Component:<br>
(3) Component:<br>
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补2.png|500px|frameless|thumb]]<br>
(4)Connection Diagram:<br>
(4)Connection Diagram:<br>
<br>[[File:0507--17.png|500px|frameless|thumb]]<br>
<br>[[File:0507--17.png|500px|frameless|thumb]]<br>
Line 630: Line 630:
</pre>
</pre>
Upload the code to development board, we observe LED get brighter when covering the line tracking sensor by hand.
Upload the code to development board, we observe LED get brighter when covering the line tracking sensor by hand.
=== Project 5: PIR Motion Sensor  ===
=== Project 5: PIR Motion Sensor  ===
(1)Description:<br>
(1)Description:<br>
Line 651: Line 652:
5. Done powering up and uploading the code, you need to wait 5-10 seconds then start testing, otherwise it is not sensitive.</span><br>
5. Done powering up and uploading the code, you need to wait 5-10 seconds then start testing, otherwise it is not sensitive.</span><br>
(3)Component:<br>
(3)Component:<br>
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补3.png|500px|frameless|thumb]]<br>
(4)Connection Diagram<br>
(4)Connection Diagram<br>
<span style=color:red>Note: on expansion board, the pin G, V and S of PIR motion sensor are connected to G, V and 47; pin G, V and S of LED module are connected to G, V and 13.</span><br>
<span style=color:red>Note: on expansion board, the pin G, V and S of PIR motion sensor are connected to G, V and 47; pin G, V and S of LED module are connected to G, V and 13.</span><br>
Line 732: Line 733:
* Port:digital port
* Port:digital port
(3)Component:<br>
(3)Component:<br>
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补4.png|500px|frameless|thumb]]<br>




Line 780: Line 781:
Download code, open serial monitor and set baud rate to 9600. The serial monitor will show the corresponding key value when the key of membrane keypad is pressed, as shown below;<br>
Download code, open serial monitor and set baud rate to 9600. The serial monitor will show the corresponding key value when the key of membrane keypad is pressed, as shown below;<br>
<br>[[File:0507--B.png|500px|frameless|thumb]]<br>
<br>[[File:0507--B.png|500px|frameless|thumb]]<br>
=== Project 7: Power Amplifier Module ===   
=== Project 7: Power Amplifier Module ===   
(1)Description:<br>
(1)Description:<br>
Line 791: Line 793:
* Working voltage: DC 3.3-5V
* Working voltage: DC 3.3-5V
(3) Component:
(3) Component:
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补5.png|500px|frameless|thumb]]<br>
(4) Connection Diagram:<br>
(4) Connection Diagram:<br>
<span style=color:red>Note: the pin G, V and S of passive buzzer are connected to pin G, V and D49 of expansion board</span><br>
<span style=color:red>Note: the pin G, V and S of passive buzzer are connected to pin G, V and D49 of expansion board</span><br>
Line 924: Line 926:


(3)Component:
(3)Component:
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
 
<br>[[File:0507--补7.png|500px|frameless|thumb]]<br>


(4)Connection Diagram:<br>
(4)Connection Diagram:<br>
<br>[[File:0507--E.png|500px|frameless|thumb]]<br>
<br>[[File:0507--E.png|500px|frameless|thumb]]<br>


Line 1,001: Line 1,005:
}
}
</pre>
</pre>
=== Project 9: Adjustable Rotary Potentiomete ===
=== Project 9: Adjustable Rotary Potentiomete ===
(1)Description:
(1)Description:
Line 1,010: Line 1,015:
* Interface: analog interface
* Interface: analog interface
(3)Component:
(3)Component:
<br>[[File:0507--.png|500px|frameless|thumb]]<br>
<br>[[File:0507--补8.png|500px|frameless|thumb]]<br>


(4)Connection Diagram:<br>
(4)Connection Diagram:<br>
Line 1,068: Line 1,073:
}
}
</pre>
</pre>
=== Project10: Ambient Light Sensor ===  
=== Project10: Ambient Light Sensor ===  
(1)Description:<br>
(1)Description:<br>
Line 1,254: Line 1,260:
(7) Project Extension:<br>
(7) Project Extension:<br>
Power amplifier module will alarm when the detected combustible gas is leaked.<br>
Power amplifier module will alarm when the detected combustible gas is leaked.<br>
<br>[[File:0507--H.png|500px|frameless|thumb]]<br>
<br>[[File:0507--H.png|400px|frameless|thumb]]<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 12.2
  MQ2
  http://www.keyestudio.com
*/
#define MQ2_A  A0  // define MQ2_A as A0
#define MQ2_D  A1  //define MQ2_A as A1
#define buzzer  49 //buzzer pin to D49
volatile int analogVal, digitalVal;
 
void setup() {
  Serial.begin(9600);
 
}
 
void loop () {
  analogVal = analogRead(MQ2_A);  //read the analog value
  Serial.println(analogVal);      //print the value of sensor
  if (analogVal > 150) {          //when analog value exceeds 150, the buzzer will alarm
    tone(buzzer, 1000);
  }
  else {
    noTone(buzzer); //turn off buzzer
  }
  delay(100);
 
}
</pre>
 
=== Project 13 DHT11 Temperature and Humidity Sensor ===
<br>[[File:0507--I.png|500px|frameless|thumb]]<br>This DHT11 Temperature and Humidity Sensor is a composite sensor which contains a calibrated digital signal output of the temperature and humidity.Its technology ensures high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected.This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance advantages.Each DHT11 sensor features extremely accurate calibration data of humidity calibration chamber. The calibration coefficients stored in the OTP program memory, internal sensors detect signals in the process, and we should call these calibration coefficients.The single-wire serial interface system is integrated to make it quick and easy. Qualities of small size, low power, and 20-meter signal transmission distance make it a wide applied application or even the most demanding one. <br>
 
(2) Specification:<br>
* Supply Voltage: +5 V
* Temperature range: 0-50 ℃ error of ± 2 ℃
* Humidity: 20-90% RH ± 5% RH error
* Interface: Digital
 
 
(3) Component:<br>
<br>[[File:0507--X.png|500px|frameless|thumb]]<br>
(8)Connection Diagram:<br>
<br>[[File:0507--图片1.png|400px|frameless|thumb]]<br>
<span style=color:red>In the project, we need to import the library of DHT11.</span><br>
(9)Test Code:<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 13.1
  DHT11
  http://www.keyestudio.com
*/
#include <dht11.h>  //include the library code:
dht11 DHT;
#define DHT11_PIN 47 //define DHT11 as 48
 
void setup() {
  Serial.begin(9600);
 
}
 
void loop () {
  int chk;
  chk = DHT.read(DHT11_PIN);    // READ DATA
  switch (chk) {
    case DHTLIB_OK:
      break;
    case DHTLIB_ERROR_CHECKSUM:
      break;
    case DHTLIB_ERROR_TIMEOUT:
      break;
    default:
      break;
  }
  // DISPLAT DATA
  Serial.print("humidity:");
  Serial.print(DHT.humidity);
  Serial.print("  temperature:");
  Serial.println(DHT.temperature);
  delay(100);
}
</pre>
(10)Test Result:<br>
Upload code, power on with USB cable,open serial monitor and the temperature and humidity data is shown below:<br>
<br>[[File:0507--Z.png|500px|frameless|thumb]]<br>
=== Project 14 Servo Control === 
<br>[[File:0507--图片2.png|300px|frameless|thumb]]<br>
(1)Description <br>
Servo motor is a position control rotary actuator. It mainly consists of housing, circuit board, core-less motor, gear and position sensor. Its working principle is that the servo receives the signal sent by MCU or receiver and produces a reference signal with a period of 20ms and width of 1.5ms, then compares the acquired DC bias voltage to the voltage of the potentiometer and obtain the voltage difference output.<br>
 
When the motor speed is constant, the potentiometer is driven to rotate through the cascade reduction gear, which leads that the voltage difference is 0, and the motor stops rotating. Generally, the angle range of servo rotation is 0° --180 °<br>
 
The rotation angle of servo motor is controlled by regulating the duty cycle of PWM (Pulse-Width Modulation) signal. The standard cycle of PWM signal is 20ms (50Hz). Theoretically, the width is distributed between 1ms-2ms, but in fact, it's between 0.5ms-2.5ms. The width corresponds the rotation angle from 0° to 180°. But note that for different brand motor, the same signal may have different rotation angle. <br>
<br>[[File:0507--图片3.png|300px|frameless|thumb]]<br>
In general, servo has three line in brown, red and orange. Brown wire is grounded, red one is positive pole line and orange one is signal line.<br>
<br>[[File:0507--图片4.png|500px|frameless|thumb]]<br>
The corresponding servo angles are shown below:
<br>[[File:0507--图片5.png|500px|frameless|thumb]]<br>
(2)Specification<br>
Working voltage: <br>
* DC 4.8V ~ 6V
* Operating angle range: about 180 ° (at 500 → 2500 μsec)
* Pulse width range: 500 → 2500 μsec
* No-load speed: 0.12 ± 0.01 sec / 60 (DC 4.8V) 0.1 ± 0.01 sec / 60 (DC 6V)
* No-load current: 200 ± 20mA (DC 4.8V) 220 ± 20mA (DC 6V)
* Stopping torque: 1.3 ± 0.01kg · cm (DC 4.8V) 1.5 ± 0.1kg · cm (DC 6V)
* Stop current: ≦ 850mA (DC 4.8V) ≦ 1000mA (DC 6V)
* Standby current: 3 ± 1mA (DC 4.8V) 4 ± 1mA (DC 6V)
 
(3) Component:
<br>[[File:0507--图片6.png|500px|frameless|thumb]]<br>
(4) Connection Diagram:<br>
<span style=color:red>Note: The servo is connected to G (GND), V (VCC),8. The brown wire of the servo is connected to Gnd (G), the red wire is linked with 5v (V), and the orange wire is connected to digital pin 8.<br>
Remember to connect external power due to the high current of driving motor.</span><br>
<br>[[File:0507--图片7.png|400px|frameless|thumb]]<br>
(6)Test Code1:
<pre>
/*
  keyestudio smart motorhome
  lesson 14.1
  servo
  http://www.keyestudio.com
*/
int servoPin = 8; //pin of servo
 
void setup() {
  pinMode(servoPin, OUTPUT);//set the pin of servo to OUTPUT
}
void loop() {
  servopulse(servoPin, 0);//rotate to 0°
  delay(1000);//delay 1s
  servopulse(servoPin, 90);//rotate to 900°
  delay(1000);
  servopulse(servoPin, 180);//rotate to 180°
  delay(1000);
}
 
void servopulse(int pin, int myangle) { //output function
  int pulsewidth = map(myangle, 0, 180, 500, 2500); //map angle to pulsewidth
  for (int i = 0; i < 10; i++) { //output pulse
    digitalWrite(pin, HIGH);//set level of servo port to HIGH
    delayMicroseconds(pulsewidth);//delay the time of pulsewidth
    digitalWrite(pin, LOW);//set the level of servo port to LOW
    delay(20 - pulsewidth / 1000);
  }
}
//**********************************************************************************
</pre>
Upload code successfully, servo swings forth and back in the range of 0° 90° and 180°.
 
There is another guide for restraining servo---- servo library file, the following link of official website is for your reference.
https://www.arduino.cc/en/Reference/Servo<br>
 
(7)Test Code2:<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 14.2
  servo
  http://www.keyestudio.com
*/
#include <Servo.h>  //include the library code:
Servo myservo;
 
void setup() {
  myservo.attach(8);  //connect servo to digital 8
 
}
 
void loop () {
  //rotate 0° to 180°
  for (int i = 0; i < 180; i++) {
    myservo.write(i);
    delay(20);
  }
  delay(1000);  //delay in 1s
 
  //rotate from 180° to 0°
  for (int i = 180; i > 0; i--) {
    myservo.write(i);
    delay(20);
  }
  delay(1000);  //delay in 1s
}
 
//********************************************************************************
</pre>
(8)Test Result:<br>
Upload code successfully and power on, servo swings in the range of 0° to 180°. <br>
 
(9)Code Explanation:<br>
Arduino comes with #include <Servo.h> (servo function and statement)
The following are some common statements of the servo function:<br>
1. attach(interface)——Set the pin of servo.<br>
2. write(angle)——The statement to set rotation angle of servo, the angle range is from 0° to 180°.<br>
3. read()——The statement to read angle of servo, read the command value of“write()”.<br>
4. attached()——Judge if the parameter of servo is sent to its interface <br>
<span style=color:red>Note: The above written format is“servo variable name, specific statement()”, for instance: myservo.attach(8)</span><br>
=== Project 15 Ultrasonic Sensor ===
(1)Description:<br>
The HC-SR04 ultrasonic sensor uses sonar to determine distance to an object like bats do. It offers excellent non-contact range detection with high accuracy and stable readings in an easy-to-use package. It comes complete with ultrasonic transmitter and receiver modules.The HC-SR04 or the ultrasonic sensor is being used in a wide range of electronics projects for creating obstacle detection and distance measuring application as well as various other applications. Here we have brought the simple method to measure the distance with Arduino and ultrasonic sensor and how to use ultrasonic sensor with Arduino.<br>
(2) Specification:<br>
<br>[[File:0507--图片8.png|500px|frameless|thumb]]<br>
(3) Component:<br>
<br>[[File:0507--图片10.png|500px|frameless|thumb]]<br>
(4) The principle of ultrasonic sensor<br>
The ultrasonic module will emit the ultrasonic waves after trigger signal. When the ultrasonic waves encounter the object and are reflected back, the module outputs an echo signal, so it can determine the distance of object from the time difference between trigger signal and echo signal.
The t is the time that emitting signal meets obstacle and returns.<br>
and the propagation speed of sound in the air is about 343m/s, therefore,  distance = speed * time, because the ultrasonic wave emits and comes back, which is 2 times of distance, so it needs to be divided by 2, the distance measured by ultrasonic wave = (speed * time)/2<br>
 
1.Use method and timing chart of ultrasonic module:<br>
Setting the delay time of Trig pin of SR04 to 10μs at least, which can trigger it to detect distance.<br>
2. After triggering, the module will automatically send eight 40KHz ultrasonic pulses and detect whether there is a signal return. This step will be completed automatically by the module.<br>
3. If the signal returns, the Echo pin will output a high level, and the duration of the high level is the time from the transmission of the ultrasonic wave to the return.<br>
<br>[[File:0507--图片11.png|500px|frameless|thumb]]<br>
Circuit diagram of ultrasonic sensor:<br>
<br>[[File:0507--图片12.png|500px|frameless|thumb]]<br>
(5) Connection Diagram:<br>
<br>[[File:0507--图片13.png|500px|frameless|thumb]]<br>
<span style=color:red>Wiring guide:</span><br>
  <span style=color:red> Ultrasonic sensor            keyestudio V5 Sensor Shield
      VCC          →                5v(V)
    Trig          →                22(S)
    Echo        →                23(S)
    Gnd          →                Gnd(G)<br>
</span><br>
(6) Test Code:
<pre>
/*
  keyestudio smart motorhome
  lesson 15.1
  Ultrasonic sensor
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
float dis;
void setup() {
  Serial.begin(9600);
  pinMode(EchoPin, INPUT);  // set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
 
}
 
void loop () {
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger TrigPin at least 10us high level
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 2 / 29.1;  //calculate distance
  delay(50);  //delay in 50ms
  Serial.print("distance: ");
  Serial.print(dis);
  Serial.println("cm");
}
//**************************************************************************
</pre>
(7) Test Result:
Upload code to development board, open serial monitor and set baud rate to 9600. The serial monitor shows the distance, and unit is cm. The value reduces when covering the ultrasonic sensor.
<br>[[File:0507--图片14.png|500px|frameless|thumb]]<br>
(8) Code Explanation:<br>
int trigPin- this pin is defined to transmit ultrasonic waves, generally output.<br>
int echoPin - this is defined as the pin of reception, generally input<br>
 
cm = (duration/2) / 29.1<br>
inches = (duration/2) / 74<br>
 
We can calculate the distance by using the following formula:<br>
distance = (traveltime/2) x speed of sound<br>
The speed of sound is: 343m/s = 0.0343 cm/uS = 1/29.1 cm/uS<br>
Or in inches: 13503.9in/s = 0.0135in/uS = 1/74in/uS<br>
We need to divide the traveltime by 2 because we have to take into account that the wave was sent, hit the object, and then returned back to the sensor.<br>
 
(9) Extension Practice:<br>
We’ve known how to detect the distance, next, let’s try to control an LED with detected distance
Value. <br>
Connect an LED module at D13<br>
<br>[[File:0507--图片15.png|500px|frameless|thumb]]<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 15.2
  Ultrasonic sensor
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
const int LED = 13;  //led pin to D13
volatile int distance;
void setup() {
  Serial.begin(9600);
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
  pinMode(LED, OUTPUT);
}
 
void loop () {
  distance = get_distance();  //set distance to variable distance
  Serial.println(distance);
  if (distance < 10) {
    digitalWrite(LED, HIGH);
  }
  else {
    digitalWrite(LED, LOW);
  }
}
 
int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger TRIG at least 10us high level
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;  //calculate distance
  delay(10);  //delay in 50ms
  return dis;
}
 
//****************************************************************************                         
</pre>
Upload the above code to development board. Do you find LED on when covering ultrasonic sensor by hand?<br>
=== Project 16: 1602 LCD Display ===
(1)Description:<br>
<br>[[File:0507--图片16.png|500px|frameless|thumb]]<br>
With I2C communication module, this is a display module that can show 2 lines with 16 characters per line.<br>
It shows blue background and white word and connects to I2C interface of MCU, which highly save the MCU resources.<br>
On the back of LCD display, there is a blue potentiometer for adjusting the backlight. The communication address defaults to 0x27.<br>
The original 1602 LCD can start and run with 7 IO ports, but ours is built with ARDUINOIIC/I2C interface, saving 5 IO ports. Alternatively, the module comes with 4 positioning holes with a diameter of 3mm, which is convenient for you to fix on other devices.<br>
 
Notice that when the screen gets brighter or darker, the characters will become more visible or less visible.<br>
 
(2) Specification:<br>
* I2C address: 0x27
* Backlight (blue, white)
* Power supply voltage: 5V
* Adjustable contrast
* GND: A pin that connects to ground
* VCC: A pin that connects to a +5V power supply
* SDA: A pin that connects to analog port 20 for IIC communication
* SCL: A pin that connects to analog port 21 for IIC communication
(3) Component:<br>
<br>[[File:0507--图片17.png|500px|frameless|thumb]]<br>
(4) Connection Diagram:<br>
<span style=color:red>Note: the pin GND, VCC, SDA and SCL of 1602LCD module are connected to GND(-), 5V(+), SDA and SCL.</span><br>
<br>[[File:0507--图片18.png|500px|frameless|thumb]]<br>
(5) Test Code:<br>
<pre>
//**************************************************************************
/*
  keyestudio smart motorhome
  lesson 16.1
  I2C 1602
  http://www.keyestudio.com
*/
#include <Wire.h>
#include <LiquidCrystal_I2C.h> // includes the LiquidCrystal_I2C Library
LiquidCrystal_I2C lcd(0x27, 16, 2); // set the LCD address to 0x27 for a 16 chars and 2 line display
 
void setup() {
  lcd.init();
  // Print a message to the LCD.
  lcd.backlight();  //set backlight
  lcd.setCursor(0,0); /set cursor at the first row and first column
  lcd.print("Hello, World!"); //display "Hello, World!"
  lcd.setCursor(0,1); //at the second row and first column
  lcd.print("Hello, Keyes!"); //show "Hello, Keyes!"
}
 
void loop () {
 
}
//************************************************************************
</pre>
(6) Test Result:<br>
 
Upload code, wire up according to connection diagram and power on. 1602 LCD will display“Hello World!”at the first row and show“Hello Keyes!”at the second row.<br> 
 
<span style=color:red>Note: wire up connection diagram, upload code and power on. You can adjust the potentiometer on the back of 1602LCD display module to display the character strings</span><br>
 
 
=== Project 17: 2812 Light Strip ===
                                 
(1)Description:<br>
This module is an intelligent controlled LED light source that integrates the control circuit and light-emitting circuit.
Each LED shape is as same as a 5050LED bead. Each element is a pixel. Each pixel interior includes not only intelligent digital port data latch and signal reshaping amplification drive circuit, but also a precision internal oscillator and a 12V programmable constant current control part, effectively ensuring the highly consistency of the pixel point light color.<br>
 
The data transfer protocol uses single RZ (return-to-zero) communication mode. After the pixel power-on to reset, the DI port receives data from controller, the first 24bit data is extracted by the first pixel, and then sent to the data latch inside the pixel. After being amplified by the internal shaping processing circuit, the remaining data will be forwarded to the next cascade pixel point through the DO port of the LED.<br>
The signal will be reduced by 24bit for each pixel point transmission. <br>
The pixel point adopts automatic transfer technology so that the number of cascade pixel are only limited by signal transmission speed rather than signal transmission.<br>
 
 
(2)Specification:<br>
 
* LED: WS2812
* Working voltage: DC 5V
* Working current: 40mA*10*2=8000mA (maximum) (each RGB lamp current 40mA)
* Wiring mode: G-GND V-VCC (DC 5V) DI (signal input terminal) DO (signal output terminal, used in cascade connection)
(3)Component:<br>
<br>[[File:0507--图片19.png|500px|frameless|thumb]]<br>
(4) Connection Diagram:<br>
<span style=color:red>Note: the pin GND, VCC and DI of 8x16 LED panel are interfaced with the pin -(GND), +(VCC)and 53 of sensor expansion board.</span><br>
<br>[[File:0507--图片20.png|500px|frameless|thumb]]<br>
(5) Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 17.1
  2812 led
  http://www.keyestudio.com
*/
#include <Adafruit_NeoPixel.h>
Adafruit_NeoPixel rgb_2812 = Adafruit_NeoPixel(10, 53, NEO_GRB + NEO_KHZ800); //dset the port of 10 pcs lights to 53, with GRB mode
 
void setup() {
  rgb_2812.begin();
}
 
void loop () {
 
  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,255,0,0);  //the first light shows red color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);  //the first light turns off
    rgb_2812.show();                    //show
    delay(50);
  }
 
  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,0,255,0);  //the first light shows green color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);  //the first light turns off
    rgb_2812.show();                    //display
    delay(50);
  }
 
  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,0,0,255);  //the first light shows blue color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);  //the first light turns off
    rgb_2812.show();                    //show
    delay(50);
  }
 
}
</pre>
(6) Test Result:<br>
Upload code and power on. 2812 light strip shows red, green and blue color.<br>
 
(7) Project Extension:show gradient colour <br>
<pre>
/*
  keyestudio smart motorhome
  lesson 17.2
  2812 led
  http://www.keyestudio.com
*/
#include <Adafruit_NeoPixel.h>
Adafruit_NeoPixel rgb_2812 = Adafruit_NeoPixel(10, 53, NEO_GRB + NEO_KHZ800); //set the port of 10 pcs lights to 53, with GRB mode
 
void setup() {
  rgb_2812.begin();
}
 
void loop () {
  rainbow(20);  //keep gradient color for 20ms
 
}
 
void rainbow(uint8_t wait) {
  uint16_t i, j;
  for (j = 0; j < 256; j++) {
    for (i = 0; i <= 9; i++) {
      rgb_2812.setPixelColor(i, Wheel((i + j) & 255));
    }
    rgb_2812.show(); //display
    delay(wait);
  }
}
 
uint32_t Wheel(byte WheelPos) { //set color
  if (WheelPos < 85) {
    return rgb_2812.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
  }
  else if (WheelPos < 170) {
    WheelPos -= 85;
    return rgb_2812.Color(255 - WheelPos * 3, 0, WheelPos * 3);
  }
  else {
    WheelPos -= 170;
    return rgb_2812.Color(0, WheelPos * 3, 255 - WheelPos * 3);
  }
}
</pre>
=== Project 18 Motor Driving and Speed Control ===
                                 
(1)Description:<br>
 
There are many ways to drive the motor. Our robot car uses the most commonly used TB6612FNG. TB6612FNG is an excellent high-power motor driver IC produced by STMicroelectronics.<br>
It has large current MOSFET-H bridge structure and can directly drive two motors simultaneously. We apply the design of TB6612FNG circuit to development board, which reduces the technical difficulty of using and driving the motor.<br>
 
 
Schematic Diagram<br>
<br>[[File:0507--图片21.png|500px|frameless|thumb]]<br>
(2)Specification<br>
* Logic part input voltage: DC5V
* Driving part input voltage: DC 7-12V
* Working temperature: -20~85℃
* Power supply voltage: VM = 15V max, VCC = 2.7-5.5V
* Output current: Iout = 1.2A (average) / 3.2A (peak)
* Standby control to save power Clockwise/counterclockwise/short brake/stop motor control mode
* Built-in thermal shutdown circuit and low voltage detection circuit
* Filter capacitors on two power lines
 
 
 
(3)Working Principle
 
According to the above diagram of motor driver board, we know that speed control pins of motor A, B, C and D are D12, D11, D9 and D10; in the meanwhile, their direction control pins are D35 and D34, D33 and D32, D29 and D28, D31 and D30.<br>
In the following chart, we also know how to control the speed of four motors via digital and PWM ports<br>
PWM value is in the range of 0-255, the larger the number we set, the faster the motor rotates. <span style=color:red>(We will drive a motor, therefore, speeds can be set a value in 0~255)</span><br>
<br>[[File:0507--图片22.png|500px|frameless|thumb]]<br>
(4)Component:<br>
<br>[[File:0507--图片23.png|500px|frameless|thumb]]<br>
(5) Connection Diagram:<br>
<br>[[File:0507--图片24.png|400px|frameless|thumb]]<br>
(6) Test Code:
<pre>
/*
  keyestudio smart motorhome
  lesson 18.1
  motor
  http://www.keyestudio.com
*/
//define the pins of motor
const int Motor1 = 31;
const int Motor2 = 30;
const int PWM = 10;
 
void setup() {
  //set ports of motor to OUTPUT
  pinMode(Motor1, OUTPUT);
  pinMode(Motor2, OUTPUT);
 
}
 
void loop () {
  //rotate anticlockwise for 1
  digitalWrite(Motor1, HIGH);
  digitalWrite(Motor2, LOW);
  analogWrite(PWM, 100);
  delay(2000);
  //rotate clockwise for 1s
  digitalWrite(Motor1, LOW);
  digitalWrite(Motor2, HIGH);
  analogWrite(PWM, 100);
  delay(2000);
  //stop 1s
  analogWrite(PWM, 0);
  delay(1000);
}
//*****************************************************************************
</pre>
(7) Test Result:<br>
Upload code and power on. The motor rotates clockwise for 2s, anticlockwise for 2s and stops for 1s.<br>
 
(12)Code Explanation:<br>
digitalWrite(Motor,LOW); the rotation direction of motor is decided by the high/low level and and the pins that decide rotation direction are digital pins.<br>
 
analogWrite(PWM,100); the speed of motor is regulated by PWM, and the pins that decide the speed of motor must be PWM pins.<br>
 
(9) Extension Practice:<br>
Control car’s motion via rotation direction of motors.<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 18.2
  motor
  http://www.keyestudio.com
*/
//define the pins of motor A,B,C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
void setup() {
  //set the pins of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
 
}
 
void loop () {
  //go forward for 1s
  advance();
  delay(1000);
  //go back for 1s
  back();
  delay(1000);
  //turn left for 1s
  turnleft();
  delay(1000);
  //turn right for 1s
  turnright();
  delay(1000);
  //stop 1s
  Stop();
  delay(1000);
}
 
void advance() {    //go forward
  // motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, 150);
  //motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, 150);
  //motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, 150);
  //motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, 150);
}
 
void back() {  //go back
  //motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, 150);
  //motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, 150);
  //motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, 150);
  //motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, 150);
}
 
void turnleft() {  //turn left
  //motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, 150);
  //motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, 150);
  //motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, 150);
  //motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, 150);
}
 
void turnright() {    //turn right
  //motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, 150);
  //motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, 150);
  //motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, 150);
  //motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, 150);
}
 
void Stop() {  //Car stops
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//***********************************************************************
</pre>
Upload code and power on. The car goes forward 1s, back for 1s, turns left for 1s and right for 1s, then stops.<br>
 
=== Project 19 Bluetooth Remote Control === 
 
(1)Description:<br>
 
Bluetooth, a simple wireless communication module most popular since the last few decades and easy to use are being used in most of the battery-powered devices.<br>
<br>[[File:0507--图片25.png|400px|frameless|thumb]]<br>
Over the years, there have been many upgrades of Bluetooth standard to keep fulfil the demand of customers and technology according to the need of time and situation.<br>
Over the few years, there are many things changed including data transmission rate, power consumption with wearable and IoT Devices and Security System.<br>
Here we are going to learn about HM-10 BLE 4.0 with Arduino Board. The HM-10 is a readily available Bluetooth 4.0 module. This module is used for establishing wireless data communication. The module is designed by using the Texas Instruments CC2540 or CC2541 Bluetooth low energy (BLE) System on Chip (SoC). <br>
 
(2) Specification :<br>
* Bluetooth protocol: Bluetooth Specification V4.0 BLE
* No byte limit in serial port Transceiving
* In open environment, realize 100m ultra-distance communication with iphone4s
* Working frequency: 2.4GHz ISM band
* Modulation method: GFSK(Gaussian Frequency Shift Keying)
* Transmission power: -23dbm, -6dbm, 0dbm, 6dbm, can be modified by AT command.
* Sensitivity: ≤-84dBm at 0.1% BER
* Transmission rate: Asynchronous: 6K bytes ; Synchronous: 6k Bytes
* Security feature: Authentication and encryption
* Supporting service: Central & Peripheral UUID FFE0, FFE1
* Power consumption: Auto sleep mode, stand by current 400uA~800uA, 8.5mA during transmission.
* Power supply: 5V DC
* Working temperature: –5 to +65 Centigrade
 
(3) Component:<br>
<br>[[File:0507--图片26.png|500px|frameless|thumb]]<br>
(4) Connection Diagram:<br>
1. STATE: state test pins, connected to internal LED, generally keep it unconnected.<br>
2. RXD: serial interface, receiving terminal.<br>
3. TXD: serial interface, transmitting terminal.<br>
4. GND: Ground.<br>
5. VCC: positive pole of the power.<br>
6. EN/BRK: break connect, it means breaking the Bluetooth connection, generally, keep it unconnected.<br>
<br>[[File:0507--图片27.png|500px|frameless|thumb]]<br>
  <span style=color:red>(Notice Serial and Serial1)</span><br>
(5) Test Code:<br>
<pre>
/*
  keyestudio smart motorhome
  lesson 19.1
  bluetooth
  http://www.keyestudio.com
*/
char ble_val;  //set variable ble_val
 
void setup() {
  Serial.begin(9600);  //set USB baud rate to 9600
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
}
 
void loop () {
  if (Serial1.available() > 0) // determine if there is data in the buffer of serial port
  {
    ble_val = Serial1.read();  //read the data saved in the buffer of serial port
    Serial.println(ble_val);  //serial port prints data
  }
}
 
//**********************************************************************
</pre>
Upload code to development board and insert Bluetooth module and wait for the command from cellphone.<br>
 
(6) Download APP:<br>
The above code is used to read the received signals. Yet, we need to send signals.<br>
Next, we download an App to send signals.<br>
 
 
'''iOS System'''<br>
 
1.Open App store
2.Search <span style=color:red>'''Motorhome'''</span> and download it.<br>
 
<br>[[File:0507------1.png|300px|frameless|thumb]]  [[File:0507------2.png|300px|frameless|thumb]]<br>
 
 
The App page is shown below:<br>
 
<br>[[File:0507------3.png|500px|frameless|thumb]]<br>
 
Turn on Bluetooth of your device, and click “connect” to search and pair Bluetooth.<br>
 
[[File:0507------4.png|500px|frameless|thumb]]
 
 
'''Android System'''
 
Enter Google play store to search <span style=color:red>'''keyestudio motorhome'''</span>, or go to link to download it : https://play.google.com/store/apps/details?id=com.keyestudio.motorhome
 
[[File:0507--图片32.png|500px|frameless|thumb]]
 
[[File:0507------6.png|300px|frameless|thumb]]  [[File:0507------7.png|300px|frameless|thumb]]
 
 
<span style=color:red>'''Note: Allow APP to access“location”in settings of your cellphone when connecting to Bluetooth module, otherwise, Bluetooth may not be connected.'''</span>
 
Click [[File:0507--图片32.png|300px|frameless|thumb]] icon to enter APP, as shown below;
 
<br>[[File:0507------3.png|500px|frameless|thumb]]<br>
 
After connecting Bluetooth, plug in power and LED indicator of Bluetooth module will flash. Tap[[File:0507--图片36.png|100px|frameless|thumb]] to search Bluetooth.
 
 
<br>[[File:0507------8.png|500px|frameless|thumb]]<br>
 
Click “connect” below HMSoft, then the Bluetooth will be connected and its LED indicator will be always on.
 
<br>[[File:0507------9.png|500px|frameless|thumb]]<br>
 
After connecting Bluetooth module and opening serial monitor and setting baud rate to 9600. Press icons on APP, and the corresponding characters are displayed as shown below:
 
<br>[[File:0507------11.png|500px|frameless|thumb]]<br>
 
(7) Code Explanation:<br>
Serial.available():the number of left characters when back to buffer, this function is usually used to judge if there is data in buffer. Whenever Serial.available() is more than 0, serial will receive the data in serial monitor.<br>
Serial.read(): read a Byte in buffer of serial. We can read the data sent with Serial.read(), for instance, some devices send data to Arduino through serial monitor.<br>
 
Note: We use Serial and Serial1. Serial is used for Arduino monitor communication and Serial 1 is used for Bluetooth serial.<br>
(8) APP Interface:<br>
Open App and we will see its main interface as follows:<br>
<br>[[File:0507--图片40.png|500px|frameless|thumb]]<br>
<br>[[File:0507--图片41.png|500px|frameless|thumb]]<br>
<br>[[File:0507--图片43.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片44.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片45.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片46.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片47.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片50.png|700px|frameless|thumb]]<br>
<br>[[File:0507--图片48.png|700px|frameless|thumb]]<br>
The motorhome will emit the corresponding sound when pressing“do,re,mi,fa,so,la,si.”
(9) Extension Practice:<br>
Next, we will turn on and off LED via Bluetooth commands.<br>
<span style=color:red>Note: Allow APP to access“location”in settings of your cellphone when connecting to Bluetooth module, otherwise, Bluetooth may not be connected.<br></span><br>
<br>[[File:0507--图片51.png|500px|frameless|thumb]]<br>
<pre>
//*************************************************************************
/*
  keyestudio smart motorhome
  lesson 19.2
  bluetooth
  http://www.keyestudio.com
*/
char ble_val;  //set variable to ble_val
#define LED    13    //led pin to D13
void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  pinMode(LED, OUTPUT); //set the pin of LED to OUTPUT
 
}
 
void loop () {
  if (Serial1.available() > 0) //determine if there is data in the buffer of Bluetooth serial port
  {
    ble_val = Serial1.read();  //read the data saved in the buffer of Bluetooth serial port
    if (ble_val == 'A') {
      digitalWrite(LED, HIGH);
    }
    else if (ble_val == 'H') {
      digitalWrite(LED, LOW);
    }
  }
}
//*************************************************************************
</pre>
Click“Write”on app to send“F”or“B” to control LED.
 
=== Project 20: Install Smart Motorhome ===
 
<br>[[File:QQ图片20210322150434.png|500px|frameless|thumb]]<br>
<br>[[File:QQ图片20210322150435.png|500px|frameless|thumb]]<br>
<br>[[File:QQ图片20210322150436.png|500px|frameless|thumb]]<br>
<br>[[File:QQ图片20210322150437.png|500px|frameless|thumb]]<br>
 
<br>[[File:QQ图片20210322150438.png|500px|frameless|thumb]]<br>
 
Connection Diagram<br>
 
<br>[[File:0507--图片58.png|500px|frameless|thumb]]<br>
 
Test Code<br>
 
<pre>
#include <Servo.h>
Servo myservo1,myservo2,myservo3;  // create servo object to control a servo
 
void setup()
{
  Serial.begin(9600);
myservo1.attach(6);  // modify each pin to adjust
myservo2.attach(7);  // modify each pin to adjust
myservo3.attach(8);  // modify each pin to adjust
  myservo1.write(80);  // angle value 
  delay(1000);
myservo2.write(0);  // angle value 
  delay(1000);
myservo3.write(0);  // angle value 
  delay(1000);
}
 
void loop()
{
}
</pre>
 
'''Test Result'''<br>
 
Interface servo with D6, D7 and D8 of board, upload code and wire up. Plug in power and press reset button, servo will automatically rotate the initial angle we set.<br>
 
 
 
 
{| class="wikitable"
|-
!                    Installation Steps
|-
|                      Part 1
|-
| <br>[[File:0507==1.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==2.png|800px|frameless|thumb]]<br>
  Install button sensor on the number 19 area of board B
|-
| <br>[[File:0507==3.png|800px|frameless|thumb]]<br>
Mount power amplifier module at the number 4 area of board B,and rotate the potentiometer to the middle area.
|-
| <br>[[File:0507==4.png|800px|frameless|thumb]]<br>
Initialize servo2 and fix it on the number 5 area of board B and notice the direction.
|-
| <br>[[File:0507==5.png|800px|frameless|thumb]]<br>
Fix the cross mount on the board H
|-
| <br>[[File:0507==6.png|800px|frameless|thumb]]<br>
Use  M2*4 screws from servo and mount board H onto servo.
|-
| <br>[[File:0507==7.png|800px|frameless|thumb]]<br>
Install LED strip at the number 21 of board B.
|-
| <br>[[File:0507==8.png|800px|frameless|thumb]]<br>
|-
|                        Part 2
|-
| <br>[[File:0507==9.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==10.png|800px|frameless|thumb]]<br>
Mount gas sensor at number 3 area of board A
|-
| <br>[[File:0507==11.png|800px|frameless|thumb]]<br>
Assemble PIR motion sensor at number 2 of board A
|-
| <br>[[File:0507==12.png|800px|frameless|thumb]]<br>
Install LED strip at number 20 area of board A
|-
| <br>[[File:0507==13.png|800px|frameless|thumb]]<br>
Fix 4*4 membrane keypad onto number 1 area of board A
|-
| <br>[[File:0507==14.png|800px|frameless|thumb]]<br>
Assemble board I on board A
|-
|<br>[[File:0507==15.png|800px|frameless|thumb]]<br>
|-
|                          Part 3
|-
                    '''Components'''
| <br>[[File:0507==16.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==17.png|800px|frameless|thumb]]<br>
                  Wire up first
|-
| <br>[[File:0507==18.png|800px|frameless|thumb]]<br>
Install ultrasonic sensor onto number 8 area of board K
|-
| <br>[[File:0507==19.png|800px|frameless|thumb]]<br>
                      Wire up first
|-
|  <br>[[File:0507==20.png|800px|frameless|thumb]]<br>
Install the full-color LED module onto number 9 and 10 area of board K
|-
|  <br>[[File:0507==21.png|800px|frameless|thumb]]<br>
|-
|                          Part 4
|-
|                        Components
<br>[[File:0507==22.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==23.png|800px|frameless|thumb]]<br>
Mount the LCD display onto number 11 area of board L
|-
| <br>[[File:0507==24.png|800px|frameless|thumb]]<br>
|-
|                          Part 5
|-
| <br>[[File:0507==25.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==26.png|800px|frameless|thumb]]<br>
Respectively assemble rotary potentiometer and steam sensor at number 16 area and number 17 of board N
|-
| <br>[[File:0507==27.png|800px|frameless|thumb]]<br>
Initialize servo 1 and install it at number 19 area of board N
|-
| <br>[[File:0507==28.png|800px|frameless|thumb]]<br>
Fix servo cross mount onto gear of roof window with M2*4MM screws from servo
|-
| <br>[[File:0507==29.png|800px|frameless|thumb]]<br>
Install board O onto board N and don’t need to screw nuts tightly.
|-
| <br>[[File:0507==30.png|800px|frameless|thumb]]<br>
|-
|                          Part 6
|-
| <br>[[File:0507==31.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==32.png|800px|frameless|thumb]]<br>
Respectively install temperature  humidity sensor  and ambient light sensor at number 14 area and number 15 area of board M.
|-
| <br>[[File:0507==33.png|800px|frameless|thumb]]<br>
Fix white LED module onto number 12 area of board M
|-
| <br>[[File:0507==34.png|800px|frameless|thumb]]<br>
Adjust the angle of servo 3 and install it onto number 13 area.
|-
| <br>[[File:0507==35.png|800px|frameless|thumb]]<br>
Fix servo cross onto board E
|-
| <br>[[File:0507==36.png|800px|frameless|thumb]]<br>
Use M2*4MM screws from servo to install board E onto servo
|-
| <br>[[File:0507==37.png|800px|frameless|thumb]]<br>
Fix control board onto M board
|-
| <br>[[File:0507==38.png|800px|frameless|thumb]]<br>
|-
|                    Part 7
|-
                    Components
| <br>[[File:0507==39.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==40.png|800px|frameless|thumb]]<br>
Assemble motor parts onto board C
|-
| <br>[[File:0507==41.png|800px|frameless|thumb]]<br>
Install motors onto board and notice the direction of motors
|-
| <br>[[File:0507==42.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==43.png|800px|frameless|thumb]]<br>
Install the wheels onto motor
|-
| <br>[[File:0507==44.png|800px|frameless|thumb]]<br>
Assemble battery holder onto number 7 area of board C
|-
| <br>[[File:0507==45.png|800px|frameless|thumb]]<br>
Mount line tracking sensor onto number 6 area of board C
|-
| <br>[[File:0507==46.png|800px|frameless|thumb]]<br>
|-
|                      Part 8
|-
| Be patient please when you have difficulty in inserting them.
|-
| <br>[[File:0507==47.png|800px|frameless|thumb]]<br>
Use the bigger slots to install
|-
| <br>[[File:0507==48.png|800px|frameless|thumb]]<br>
Use the bigger slots to install
|-
| <br>[[File:0507==49.png|800px|frameless|thumb]]<br>
Make the side marked letters on board G face upward
|-
| <br>[[File:0507==50.png|800px|frameless|thumb]]<br>
Make the side marked letters on board P face forward
|-
| <br>[[File:0507==51.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==52.png|800px|frameless|thumb]]<br>
Be careful to install board because its protruding part is weak.
|-
| <br>[[File:0507==53.png|800px|frameless|thumb]]<br>
You need to remove board E, then install board F and slot.
|-
| <br>[[File:0507==54.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==55.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==56.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==57.png|800px|frameless|thumb]]<br>
|-
| <br>[[File:0507==58.png|800px|frameless|thumb]]<br>
|-
|                    Wiring Up
|-
|        According to diagram to wire up
<br>[[File:0507==59.png|800px|frameless|thumb]]<br>
<br>[[File:0507(.png|800px|frameless|thumb]]<br>
<br>[[File:0507==61.png|800px|frameless|thumb]]<br>
<br>[[File:0507==62.png|800px|frameless|thumb]]<br>
<br>[[File:0507==63.png|800px|frameless|thumb]]<br>
<br>[[File:0507==64.png|800px|frameless|thumb]]<br>
<br>[[File:0507==65.png|800px|frameless|thumb]]<br>
<br>[[File:0507==66.png|800px|frameless|thumb]]<br>
<br>[[File:0507==67.png|800px|frameless|thumb]]<br>
<br>[[File:0507==68.png|800px|frameless|thumb]]<br>
<br>[[File:0507==69.png|800px|frameless|thumb]]<br>
<br>[[File:0507==70.png|800px|frameless|thumb]]<br>
<br>[[File:0507==71.png|800px|frameless|thumb]]<br>
<br>[[File:0507==72.png|800px|frameless|thumb]]<br>
<br>[[File:0507==73.png|800px|frameless|thumb]]<br>
<br>[[File:0507==74.png|800px|frameless|thumb]]<br>
<br>[[File:0507==75.png|800px|frameless|thumb]]<br>
<br>[[File:0507==76.png|800px|frameless|thumb]]<br>
<br>[[File:0507==77.png|800px|frameless|thumb]]<br>
<br>[[File:0507==78.png|800px|frameless|thumb]]<br>
<br>[[File:0507==79.png|800px|frameless|thumb]]<br>
<br>[[File:0507==80.png|800px|frameless|thumb]]<br>
<br>[[File:0507==81.png|800px|frameless|thumb]]<br>
<br>[[File:0507==82.png|800px|frameless|thumb]]<br>
<br>[[File:0507==83.png|800px|frameless|thumb]]<br>
<br>[[File:0507==84.png|800px|frameless|thumb]]<br>
<br>[[File:0507==85.png|800px|frameless|thumb]]<br>
<br>[[File:0507==86.png|800px|frameless|thumb]]<br>
<br>[[File:0507==87.png|800px|frameless|thumb]]<br>
<br>[[File:0507==88.png|800px|frameless|thumb]]<br>
<br>[[File:0507==89.png|800px|frameless|thumb]]<br>
<br>[[File:0507==90.png|800px|frameless|thumb]]<br>
<br>[[File:0507==91.png|800px|frameless|thumb]]<br>
<br>[[File:0507==92.png|800px|frameless|thumb]]<br>
<br>[[File:0507==93.png|800px|frameless|thumb]]<br>
<br>[[File:0507==94.png|800px|frameless|thumb]]<br>
<br>[[File:0507==95.png|800px|frameless|thumb]]<br>
<br>[[File:0507==96.png|800px|frameless|thumb]]<br>
<br>[[File:0507==97.png|800px|frameless|thumb]]<br>
<br>[[File:0507==98.png|800px|frameless|thumb]]<br>
<br>[[File:0507==99.png|800px|frameless|thumb]]<br>
<br>[[File:0507==100.png|800px|frameless|thumb]]<br>
<br>[[File:0507==101.png|800px|frameless|thumb]]<br>
<br>[[File:0507==102.png|800px|frameless|thumb]]<br>
<br>[[File:0507==103.png|800px|frameless|thumb]]<br>
<br>[[File:0507==104.png|800px|frameless|thumb]]<br>
<br>[[File:0507==105.png|800px|frameless|thumb]]<br>
Note: be careful to mount board because its protruding part is weak.
<br>[[File:0507==106.png|800px|frameless|thumb]]<br>
<br>[[File:0507==107.png|800px|frameless|thumb]]<br>
<br>[[File:0507==108.png|800px|frameless|thumb]]<br>
|-
|}
 
=== Project 21: Line Tracking Motorhome ===
<br>[[File:0507--图片60.png|500px|frameless|thumb]]<br>
(1)Description:<br>
We’ve introduced how to work with sensors and modules. In this part, we will integrate some modules to finish more complex program. Next, we will make a line tracking smart motorhome.<br>
<br>[[File:0507--?.png|500px|frameless|thumb]]<br>
Flow Chart<br>
<br>[[File:0507--图片61.png|500px|frameless|thumb]]<br>
(2)Connection Diagram<br>
<br>[[File:0507--图片62.png|500px|frameless|thumb]]<br>
(3)Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 21
  Tracking motorhome
  http://www.keyestudio.com
*/
//Line Tracking Sensor
#define L_pin  50
#define M_pin  51
#define R_pin  52
 
//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
volatile int speeds = 120;  //define the speed variable speeds
void setup() {
  pinMode(L_pin, INPUT); //set the pins of line tracking sensor to INPUT
  pinMode(M_pin, INPUT);
  pinMode(R_pin, INPUT);
 
  //set ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}
 
void loop () {
  int L_val = digitalRead(L_pin); //read the value of left sensor
  int M_val = digitalRead(M_pin); //read the value of middle sensor
  int R_val = digitalRead(R_pin); //read the value of right sensor
  if (M_val == 1) { //the middle one detects black line
    if (L_val == 1 && R_val == 0) { //if only left sensor detects black line, turn left
      turnleft();
    }
    else if (L_val == 0 && R_val == 1) { //if only right sensor detects black line, turn right
      turnright();
    }
    else { //go forward
      advance();
    }
  }
  else { //the middle sensor detects black line
    if (L_val == 1 && R_val == 0) { //if only left sensor detects black line, turn left
      turnleft();
    }
    else if (L_val == 0 && R_val == 1) { //if only right sensor detects black line,turn right
    }
    else { //stop
      Stop();
    }
  }
 
}
 
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void back() {  //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void turnleft() {  //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void Stop() {  //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//*******************************************************************************
</pre>
 
 
(4)Test Result<br>
Upload code to development board and power on. The smart motorhome runs along black tracks. However, if it deviates from the track, the RV can automatically adjust back.<br>
     
=== Project 22: Ultrasonic Follow Motorhome ===
<br>[[File:0507--图片63.png|500px|frameless|thumb]]<br>
(1) Description:
In this lesson, we will make an ultrasonic follow motorhome based on the working principle of ultrasonic sensor. The ultrasonic sensor detects the distance between obstacle and car. Then we will drive motorhome to move through the distance value.<br>
<br>[[File:0507--图片64.png|500px|frameless|thumb]]<br>
Flow Chart
<br>[[File:0507--图片65.png|500px|frameless|thumb]]<br>
(3) Connection Diagram<br>
<br>[[File:0507--图片66.png|500px|frameless|thumb]]<br>
(4) Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 22
  flowing motorhome
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
 
//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
volatile int speeds = 120;  //define the speed variable speeds
volatile int distance;
void setup() {
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}
 
void loop () {
  distance = get_distance();
  if (distance <= 8) {
    back();
  }
  else if (distance > 8 && distance <= 15) {
    Stop();
  }
  else if (distance > 15 && distance <= 35) {
    advance();
  }
  else {
    Stop();
  }
 
}
 
int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger at least 10us high level to TRIG
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;  //calculate the distance
  delay(10);
  return dis;
}
 
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void back() {  //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void turnleft() {  //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void Stop() {  //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//***********************************************************************************************
</pre>
(5) Test Result</pre>
 
Upload code to development board and wire up according to connection diagram. The smart motorhome will follow the obstacle to move.<pre>
 
 
=== Project 23: Ultrasonic Obstacle Avoidance Motorhome ===
<br>[[File:0507--图片67.png|500px|frameless|thumb]]<br>
(1)Description:<br>
In previous lesson, we made a follow smart motorhome. Equally, we can transform it into ultrasonic obstacle avoidance motorhome through code. Let’s get started.<br>
<br>[[File:0507--图片68.png|500px|frameless|thumb]]<br>
Flow Chart<br>
<br>[[File:0507--图片69.png|500px|frameless|thumb]]<br>
(2)Connection Diagram<br>
<br>[[File:0507--图片70.png|500px|frameless|thumb]]<br>
(3)Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 23
  avoiding motorhome  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
 
//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
volatile int speeds = 120;  //define the speed variable speeds
volatile int distance;
void setup() {
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
 
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}
 
void loop () {
  distance = get_distance();  //set the distance to variable distance
  if (distance < 8) {
    back();
    delay(300);
  }
  else if (distance < 15) {
    turnleft();
    delay(300);
  }
  else {
    advance();
  }
 
}
 
int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger at least 10us high level to TRIG
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;  //计calculate the distance
  delay(10);
  return dis;
}
 
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void back() {  //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void turnleft() {  //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void Stop() {  //stop
  //set the speed of four motors to
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
</pre>
(4)Test Result<br>
Upload code successfully, power on and smart motorhome goes forward. It can avoid the obstacle when meeting obstacle<br>
 
 
=== Project 24: Bluetooth Control motorhome ===
<br>[[File:0507--图片71.png|500px|frameless|thumb]]<br>
(1) Description:<br>
We’ve learned the basic knowledge of Bluetooth, in this lesson, we will make a Bluetooth smart motorhome. In the experiment, we default the HM-10 Bluetooth module as a Slave and the cellphone as a Host. <br>
Then install an App and connect to HM-10 Bluetooth module so as to control smart motorhome. Next, let’s control it through the key value of App.<br>
 
<span style=color:red>Note: pin RXD1, TXD1, GND and VCC of Bluetooth module are interfaced with pin TX1, RX1, -(GND)and +(VCC)of mega2560 control board. Pin STATE and BRK don’t need connecting and BAT is connected to power.</span><br>
 
 
The corresponding key values are shown below:<br>
<br>[[File:0507--图片72.png|500px|frameless|thumb]]<br>
Flow Chart:
<br>[[File:0507--图片73.png|500px|frameless|thumb]]<br>
(3) Connection Diagram<br>
<br>[[File:0507--图片74.png|500px|frameless|thumb]]<br>
(4) Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 24.1
  Bluetooth control motorhome
  http://www.keyestudio.com
*/
 
//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
volatile int speeds = 120;  //define the speed variable speeds
char ble_val;  //set variable ble_val
void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}
 
void loop () {
  if (Serial1.available() > 0) //serial port reads characters
  {
    ble_val = Serial1.read();//set the character read by serial port to val
      case 'F':  advance();    break;
      case 'B':  back();      break;
      case 'L':  turnleft();  break;
      case 'R':  turnright();  break;
      case 'S':  Stop();      break;
    }
  }
 
}
 
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void back() {  //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void turnleft() {  //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void Stop() {  //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//*********************************************************************************************
 
(2)Test Result 
Upload code to development board, insert Bluetooth module, open App and connect Bluetooth. The smart motorhome reacts the corresponding action by pressing icons on the app
 
 
(6) Project Extension:adjust speed via App
/*
  keyestudio smart motorhome
  lesson 24.2
  Bluetooth control motorhome
  http://www.keyestudio.com
*/
 
//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;
 
const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;
 
const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;
 
const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;
 
volatile int speeds = 120;  //define the speed variable speeds
char ble_val;  //set variable ble_val
 
void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  Serial.begin(9600);
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);
 
  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);
 
  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);
 
  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}
 
void loop () {
  if (Serial1.available() > 0) //serial port reads characters
  {
    ble_val = Serial1.read();//set the character read by serial port to val
    switch (ble_val) {
      case 'F':  advance();    break;
      case 'B':  back();      break;
      case 'L':  turnleft();  break;
      case 'R':  turnright();  break;
      case 'S':  Stop();      break;
      case  'W':  speeds_a();  break;  //receive ‘W’, speed up
      case  'Z':  speeds_d();  break; //receive "Z", speed down
    }
  }
 
}
 
void speeds_a() { //increment function
  int a_flag = 1; //used for while loop
  while (a_flag) {
    Serial.println(speeds);  //display velocity
    if (speeds < 255) { //increase to 255(MAX)
      speeds++;
      delay(15);  //adjust the rate of acceleration
    }
    ble_val = Serial1.read();
    if (ble_val == 'S')a_flag = 0; //receive‘S’, stop speeding up
  }
}
 
void speeds_d() { //Deceleration function
  int d_flag = 1; //used for while loop
  while (d_flag) {
    Serial.println(speeds);  //display speed
    if (speeds > 0) { //decrease to 0
      speeds--;
      delay(15);    //adjust the rate of deceleration
    }
    ble_val = Serial1.read();
    if (ble_val == 'S')d_flag = 0; //receive ‘S’and stop speeding down
  }
}
 
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void back() {  //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void turnleft() {  //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}
 
void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}
 
void Stop() {  //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
</pre>
Upload code, power on and connect to App. The speed is increasing to 255 when the speed-up button is pressed, however, speed is reducing to 0 when the speed-down button is pressed. As shown below:<br>
<br>[[File:0507--图片75.png|500px|frameless|thumb]]<br>
=== Project 25: Multi-purpose Smart Motorhome ===
In this chapter, we will test the function of smart motorhome via App. And we combine all functions together to make motorhome perform them.<br>
Next we will make a comprehensive flow chart, test the wiring-up and upload code to make a multi-purpose smart motorhome.<br>
 
For this comprehensive project, you can download tutorial in the link: https://fs.keyestudio.com/KS0507

Latest revision as of 10:21, 6 April 2022


thumb

About keyestudio

Keyestudio is a best-selling brand owned by KEYES Corporation. Our product lines range from controller boards, shields and sensor modules to smart car and complete starter kits for Arduino, Raspberry Pi and BBC micro:bit, which can help customers at any level learn electronics and programming knowledge. Likewise, all of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.
You can obtain the details and the latest information through visiting the following web sites:http://www.keyestudio.com


References and After-sales Service

1.Download Profile:https://fs.keyestudio.com/KS0507
2.Feel free to contact us please, if there is missing part or you encounter some troubles. Welcome to send email to us:service@keyestudio.com. We will update projects and products continuously from your sincere advice.


Warning

1.This product contains tiny parts(screws, copper pillars), keep it out of reach of children under 7 years old please.
2.This product contains conductive parts (control board and electronic module). Please operate according to the requirements of tutorial. Improper operation may cause parts to overheat damage. Do not touch and immediately disconnect the circuit power.

Copyright

The keyestudio trademark and logo are the copyright of KEYES DIY ROBOT co.,LTD. All products under Keyestudio brand can’t be copied, sold and resold without authorization by anyone or company. If you’re interested in our items, please contact to our sales representatives: fennie@keyestudio.com


Description:

When it comes to programming, many think it difficult. However, KEYES group issues a smart RV kit to cope with this problem.
This is low cost, easy-to-build and open source programming kit-----smart RV.
It integrates smart home and robot car. In addition, it helps you absorb the knowledge of programming like electronics, control logic and computing and science.
In compliance with the tutorial, you can create your own robot by boards, slot connection and wiring. In the assembly process, the detailed projects will guide you to learn the working principle of sensors and modules.
What’s more, it a has temperature humidity sensor and an LCD display except LED, line tracking sensor, ultrasonic sensor, Bluetooth module and motor driving modules.
Should you are interested in STEM and code programming, you can customize your RV by altering code and adding extra modules. That sounds entertaining, right? Let’s get started1

Features

  • Multi-purpose function:obstacle avoidance, line tracking, Bluetooth control, ultrasonic follow, smart sensation and so on.
  • Easy to build:Slot connection and without soldering circuit
  • Novel style:Adopt strong wood board, acrylic board, RGB and lcd1602 modules.
  • High extension:configure motor driving chip, preserve IIC, UART and SPI port and expand other sensor and module.
  • Basic programming learning:use C language and code

Specification:

  • Working voltage: 5v
  • Input voltage: 7-12V
  • Maximum output current: 3A
  • Maximum power dissipation: 15W
  • Motor speed: 200 rpm (4.5V)
  • Motor driving form: TB6612 chip drive
  • Ultrasonic sensing angle: <15 degrees
  • Ultrasonic detection distance: 2cm-400cm
  • Bluetooth remote control distance: 50 meters (measured)
  • Bluetooth APP control: support Android and iOS system


Kit

Remember to check if the components received are in line with the following product list when you getting this kit.


thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb


Getting Started with Arduino

Installing Arduino IDE

When we get control board, we need to download Arduino IDE and driver firstly. You could download Arduino IDE from the official website:
https://www.arduino.cc/, click the SOFTWARE on the browse bar, click“DOWNLOADS” to enter download page, as shown below:


thumb

You can download either Windows win7 and newer or Windows ZIP file.
The first one doesn’t require

There are two versions of IDE for WINDOWS system, you can choose from the Installer (.exe) and the Zip packages. We suggest you use the first one that installs directly everything you need to use the Arduino Software (IDE), including the drivers.
With the Zip package you need to install the drivers manually. The Zip file is also useful if you want to create a portable installation.


thumb

thumb

You just need to click JUST DOWNLOAD.

Keyestudio MEGA 2560 Smart Development Board

We need to know keyestudio MEGA 2560 development board, as a core of this smart car.


thumb

The processor core of MEGA 2560 board is ATMEGA2560-16AU, with the cp2102 chip.
It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, 1 ICSP header, and a reset button.
It can be interfaced computer with external power with a USB cable.


thumb

thumb

Install Driver on Windows System

Let’s install the driver of keyestudio MEGA 2560 smart development board. The USB-TTL chip on this board adopts CP2102 serial chip. The driver program of this chip is included in Arduino 1.8 version and above, which is convenient. Plugged in USB port, the computer can recognize the hardware and automatically install the driver of CP2102.

If install unsuccessfully, or you intend to install manually, open the device manager of computer. Right click Computer----- Properties----- Device Manager.


thumb

There is a yellow exclamation mark on the page, which implies installing unsuccessfully. Then we double click the hardware and update the driver.


thumb

Click “OK” to enter the following page, click“browse my computer for updated driver software”, find out the installed or downloaded ARDUINO software. As shown below:


thumb

There is a DRIVERS folder in Arduino software installed package. Just open driver folder and you can see the driver of CP210X series chips.


We click “Browse”, then find out the driver folder, or you could enter “driver” to search in rectangular box, then click“next”, the driver will be installed successfully. (I place Arduino software folder on the desktop, you can follow my way)


thumb

thumb

Open device manager, we will find the yellow exclamation mark disappear. The driver of CP2102 is installed successfully.


thumb

Install Driver on MAC System

The USB to serial chip of control board is CP2102. We install driver on MAC as follows: https://wiki.keyestudio.com/How_to_Install_the_Driver_of_CP2102_on_MAC_System


Arduino IDE Setting

Click0486-12.png icon,open Arduino IDE.


0507--25.png


To avoid the errors when uploading the program to the board, you need to select the correct Arduino board that matches the board connected to your computer. Then come back to the Arduino software, you should click Tools→Board, select the board. (as shown below)


0507--26.png


Then select the correct COM port (you can see the corresponding COM port after the driver is successfully installed)


0507-22.png

0507--28.png

Before uploading the program to the board, let’s demonstrate the function of each symbol in the Arduino IDE toolbar.


0507--29.png


  • A- Used to verify whether there is any compiling mistakes or not.
  • B- Used to upload the sketch to your Arduino board.
  • C- Used to create shortcut window of a new sketch.
  • D- Used to directly open an example sketch.
  • E- Used to save the sketch.
  • F- Used to send the serial data received from board to the serial monitor.


Note: the setting method on Mac system is same as on Windows system except different COM port, as shown below:


0497=图片8.png

Start First Program

We’ve known how to download and install the driver of development board , next, we will burn a code to show“Hello World!”in the monitor.

Test Code


void setup() {
  // initialize serial communication at 9600 bits per second:
  Serial.begin(9600);   
}

void loop() {
  // print out "Hello world!"
  Serial.println("Hello world!");
  delay(1000);// delay 1 second
}


Open Arduino IDE, and set board as follows:


0507--31.png


Set COM port, as shown below:


0507--32.png

Click 0486-20.png to start compiling the program, and check errors.
Click 0486-23.png to upload the program, upload successfully.


0507--33.png

Upload the program successfully, open serial monitor and set baud rate to 9600. Monitor will print“Hello World!”each 1s.
Congratulation, you finish the first program.


0507--34.png

Projects

For detailed projects, nevigated the website https://fs.keyestudio.com/KS0507


The whole project begins with basic program. Starting from simple to complex, the lessons will guide you to assemble smart RV and absorb the knowledge of electronic and machinery step by step. I reckon that you might hardly sit still and itch to have a go, let’s get started.

Note: (G), marked on each sensor and module, is negative pole and connected to“G”,“-”or“GND”on the sensor shield or control board ; (V) is positive pole and interfaced with“V”,“VCC”,“+”or“5V”on the sensor shield or control board.

Project 1: LED Blink

(1)Description:


0507--1.png

For the starter and enthusiast, this is a fundamental program---LED Blink. LED, the abbreviation of light emitting diodes, consist of Ga, As, P, N chemical compound and so on. It is often applied to numbers and text display as an indicator in the circuit.

The LED can flash diverse color by altering the delay time in the test code. When in control, power on GND and VCC, the LED will be on if S end is high level; nevertheless, it will go off.

(2) Parameter:


0507--2.png 0507--3.png

  • Control interface: digital port
  • Working voltage: DC 3.3-5V
  • Pin spacing: 2.54mm
  • LED display color: red


(3) Component:


0507--4.png

(4)Connection Diagram:


0507--5.png

From the above diagram, pin -, + and S of LED module are respectively connected to pin G, 5V and D13 of expansion board. Then we compile the code as follows:


(5)Test Code:

  /*
  keyestudio smart RV
  lesson 1.1
  Blink
  http://www.keyestudio.com
*/
#define LED  13 //define the pin of LED as D13
void setup()
{
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}
void loop() // the loop function runs over and over again forever
{
  digitalWrite(LED, HIGH);   // turn the LED on (HIGH is the voltage level
  delay(1000);    // wait for a second
  digitalWrite(LED, LOW);    // turn the LED off by making the voltage LOW
  delay(1000);    // wait for a second
}
//*******************************************************************


(6)Test Result:

Upload the program, LED blinks with the interval of 1s.

(7)Code Explanation:

pinMode(LED,OUTPUT) - This function can denote that the pin is INPUT or OUTPUT.
digitalWrite(LED,HIGH) - When pin is OUTPUT, we can set it to HIGH(output 5V) or LOW(output 0V).

(8)Extension Practice:
The LED flashes for 1s through the test result, therefore, pins and delay time affect flash frequency.

/*
  keyestudio smart RV
  lesson 1.2
  Blink
  http://www.keyestudio.com
*/
#define LED 13 //Define the pin of LED as D13
void setup()
{
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}
void loop() // the loop function runs over and over again forever
{
  digitalWrite(LED, HIGH);   // turn LED on (HIGH is the voltage level
  delay(100);    // wait for a second
  digitalWrite(LED, LOW);    // turn LED off by making the voltage LOW
  delay(100);    // wait for a second
}
//****************************************************************

The LED flashes faster through the lesson 1.2 test.

Project 2: Adjust LED Brightness

(1)Description: In previous lesson, we control LED on and off and make it blink. In this project, we will control LED brightness through PWM to simulate breathing effect. Similarly, you can change the step length and delay time in the code so as to demonstrate different breathing effect.

PWM is a means of controlling the analog output via digital means. Digital control is used to generate square waves with different duty cycles (a signal that constantly switches between high and low levels) to control the analog output.In general, the input voltage of port are 0V and 5V. What if the 3V is required? Or what if switch among 1V, 3V and 3.5V? We can’t change resistor constantly. For this situation, we need to control by PWM.


thumb
For the Arduino digital port voltage output, there are only LOW and HIGH, which correspond to the voltage output of 0V and 5V. You can define LOW as 0 and HIGH as 1, and let the Arduino output five hundred 0 or 1 signals within 1 second.
If output five hundred 1, that is 5V; if all of which is 1, that is 0V. If output 010101010101 in this way then the output port is 2.5V, which is like showing movie. The movie we watch are not completely continuous. It actually outputs 25 pictures per second. In this case, the human can’t tell it, neither does PWM. If want different voltage, need to control the ratio of 0 and 1. The more 0,1 signals output per unit time, the more accurately control.
(2)Component:

thumb
(3)Connection Diagram:
We keep connection diagram unchanged.

thumb
(4)Test Code:

/*
  keyestudio smart RV
  lesson 2.1
  PWM
  http://www.keyestudio.com
*/
#define LED 13 //Define the pin of LED as D13
int value;
void setup()
{
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}
void loop () {
  for (value = 0; value < 255; value = value + 1) {
    analogWrite (LED, value); // LED lights gradually light up
    delay (5); // delay 5MS
  }
  for (value = 255; value > 0; value = value - 1) {
    analogWrite (LED, value); // LED gradually goes out
    delay (5); // delay 5MS
  }
}

(5) Test Result:
Upload test code successfully, LED gradually becomes brighter then darker, like human breath.

(6) Code Explanation When we need to repeat some statements, we could use FOR statement. FOR statement format is shown below:


thumb
FOR cyclic sequence:
Round 1:1 → 2 → 3 → 4
Round 2:2 → 3 → 4 …
Until number 2 is not established, “for”loop is over, After knowing this order, go back to code:

for (int value = 0; value < 255; value=value+1){

       ...}

for (int value = 255; value >0; value=value-1){

      ...}


The two“for”statements make value increase from 0 to 255, then reduce from 255 to 0, then increase to 255,....infinitely loop There is a new function in the following ----- analogWrite()
We know that digital port only has two state of 0 and 1. So how to send an analog value to a digital value? Here,this function is needed. Let’s observe the Arduino board and find 6 pins marked“~”which can output PWM signals.
Function format as follows:

analogWrite(pin,value)
analogWrite() is used to write an analog value from 0~255 for PWM port, so the value is in the range of 0~255. Attention that you only write the digital pins with PWM function, such as pin 3, 5, 6, 9, 10, 11.
PWM is a technology to obtain analog quantity through digital method. Digital control forms a square wave, and the square wave signal only has two states of turning on and off (that is, high or low levels). By controlling the ratio of the duration of turning on and off, a voltage varying from 0 to 5V can be simulated. The time turning on(academically referred to as high level) is called pulse width, so PWM is also called pulse width modulation.
Through the following five square waves, let’s acknowledge more about PWM.

thumb


In the above figure, the green line represents a period, and value of analogWrite() corresponds to a percentage which is called Duty Cycle as well. Duty cycle implies that high-level duration is divided by low-level duration in a cycle. From top to bottom, the duty cycle of first square wave is 0% and its corresponding value is 0. The LED brightness is lowest, that is, turn off. The more time high level lasts, the brighter the LED. Therefore, the last duty cycle is 100%, which correspond to 255, LED is brightest. 25% means darker.
PWM mostly is used for adjusting the LED brightness or rotation speed of motor.
It plays vital role in controlling smart robot car. I believe that you can’t wait to enter next project.

(7) Extension Practice:
Let’s keep pins unchanged and change the delay value, then observe how LED changes.

/*
  keyestudio smart RV
  lesson 2.2
  PWM
  http://www.keyestudio.com
*/
#define LED 13 //Define the pin of LED as D13
int value;
void setup()
{
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}
void loop () {
  for (value = 0; value < 255; value = value + 1) {
    analogWrite (LED, value); // LED lights gradually light up
    delay (20); // delay 30MS
  }
  for (value = 255; value > 0; value = value - 1) {
    analogWrite (LED, value); // LED gradually goes out
    delay (20); // delay 30MS
  }
}
//**********************************************************

Upload code to development board, the LED’s blink frequency is slower, isn’t it?

Project 3: Button Module

(1)Description:

In this project, we control LED brightness by button module. The low level(0) is output when the button is pressed; however, high level(1) is output when button is released.

(2)Specification:

  • Operating Voltage: 3.3-5V (DC)
  • Control Signal: Digital signal
  • Detection Height: 0-3 cm
  • Weight: 3.8g
  • Dimension: 34*22*15mm


(3)Component:


thumb

(4)Connection Diagram:
Note: the pin G, V and S of button sensor are interfaced with pin G, V and
D2 of expansion board, and connect pin G, V and S of LED module to G, V
and D13 of expansion board.


thumb

(5)Test Code:read the signal of button

/*
  keyestudio smart RV
  lesson 3.1
  button
  http://www.keyestudio.com
*/
#define button 2 //Define the pin of LED as D12
volatile int buttonState;  //The output level state of button module
void setup()
{
  Serial.begin(9600);//set baud rate to 9600
  pinMode(button, INPUT);// initialize digital pin button as an input.
}
void loop () {
  buttonState = digitalRead(button);
  Serial.println(buttonState);  //auto wrap and output the digital signals from digital 2
  delay(100);//delay in 100ms
}


(6)Test Result:
Upload code, open serial monitor to set baud rate to 9600. The number “1” shows up then “0” appears on the monitor.


thumb
(7)Code Explanation:
Serial.begin(9600)- Initialize serial port, set baud rate to 9600
pinMode(pin, INPUT)-This function can denote that the pin is INPUT or OUTPUT

digitalRead(pin)-Read the state of pin, which are generally HIGH and LOW level. Function digitalRead() will come back to HIGH or LOW level if pins are not connected.

(8) Extension Practice:button-controlled LED

thumb

 /*
  keyestudio smart RV
  lesson 3.2
  button
  http://www.keyestudio.com
*/
#define LED 13 //Define the pin of LED as D13
#define button 2 //Define the pin of button module as D2
volatile int buttonState;  //the state of button
void setup()
{
  Serial.begin(9600); //set baud rate to 9600
  pinMode(button, INPUT); // initialize digital pin button as an input.
  pinMode(LED, OUTPUT); // initialize digital pin LED as an output.
}
void loop ()
{
  buttonState = digitalRead(button);    //read the status of button
  if (buttonState == 0) //if the button is pressed
  {
    digitalWrite(LED, HIGH);  //Turn on LED
  }
  else
  {
    digitalWrite(LED, LOW);   //turn off LED
  }
  delay(100); //dealy in 100ms


It turns out that LED is on when the button is pressed, and LED off when button is released.

Project 4: Line Tracking Sensor

(1)Description:


thumb
The tracking sensor is actually an infrared sensor. The component used here is the TCRT5000 infrared tube.
Its working principle is to use the different reflectivity of infrared light to the color, then convert the strength of the reflected signal into a current signal. During the process of detection, black is active at HIGH level, but white is active at LOW level. The detection height is 0-3 cm.
Keyestudio 3-channel line tracking module has integrated 3 sets of TCRT5000 infrared tube on a single board, which is more convenient for wiring and control.
By rotating the adjustable potentiometer on the sensor, it can adjust the detection sensitivity of the sensor.The tracking sensor is actually an infrared sensor.

(2) Specification:

  • Operating Voltage: 3.3-5V (DC)
  • Interface: 5PIN
  • Output Signal: Digital signal
  • Detection Height: 0-3 cm


Note: Adjust the sensitivity by rotating the potentiometer before the test. The sensitivity is best when LED is at on and off state.
(3) Component:

thumb
(4)Connection Diagram:

thumb
(5)Test Code:

/*
  keyestudio smart RV 
  lesson 4.1
  Line Track sensor
  http://www.keyestudio.com
*/
//Line Tracking Sensor
#define L_pin  50
#define M_pin  51
#define R_pin  52
void setup()
{
  Serial.begin(9600); //Set baud rate to 9600
  pinMode(L_pin, INPUT); //set pins of line tracking sensor to INPUT
  pinMode(M_pin, INPUT);
  pinMode(R_pin, INPUT);
}
void loop ()
{
  int L_val = digitalRead(L_pin); //read the value of left sensor
  int M_val = digitalRead(M_pin); //read the value of middle sensor
  int R_val = digitalRead(R_pin); //read the value of right sensor
  Serial.print(L_val);
  Serial.print("  ");
  Serial.print(M_val);
  Serial.print("  ");
  Serial.print(R_val);
  Serial.println("  ");
  delay(100); //delay in 100ms
}//****************************************************************************

(6)Test Result:
Upload code to development board, open serial monitor to check the state of three line tracking sensors. When no signals are received, they are in high level state and“1”shows up ; however, 1 changes into 0 when covering sensor with white paper.
thumb
(7) Code Explanation:
Serial.begin(9600)-initialize the serial port, set serial baud rate to 9600  pinMode- define the PIN state(input and output) of MCU digitalRead- read the level status of pin(HIGH, LOW)
(8)Extension Practice:
We’ve known how line tracking sensor works, next, we connect an LED at pin 13. We will control LED on and off by line tracking sensor, as shown below

thumb
Test Code

/*
  keyestudio smart RV
  lesson 4.2
  Line Track sensor
  http://www.keyestudio.com
*/
//LED pin
#define LED 13
//Line Tracking Sensor
#define L_pin  50
#define M_pin  51
#define R_pin  52
void setup()
{
  Serial.begin(9600); //set baud rate to 9600
  pinMode(LED, OUTPUT); //set LED to OUTPUT
  pinMode(L_pin, INPUT); //set the pin of line tracking sensor to INPUT
  pinMode(M_pin, INPUT);
  pinMode(R_pin, INPUT);
}
void loop ()
{
  int L_val = digitalRead(L_pin); //read the value of left sensor
  int M_val = digitalRead(M_pin); //read the value of middle sensor
  int R_val = digitalRead(R_pin); //read the value of right sensor
  Serial.print(L_val);
  Serial.print("  ");
  Serial.print(M_val);
  Serial.print("  ");
  Serial.print(R_val);
  Serial.println("  ");
  delay(100); //delay in 100ms
  if (L_val == 0 || M_val == 0 || R_val == 0) {
    digitalWrite(LED, HIGH);
  }
  else {
    digitalWrite(LED, LOW);
  }
}
//****************************************************************************

Upload the code to development board, we observe LED get brighter when covering the line tracking sensor by hand.

Project 5: PIR Motion Sensor

(1)Description:

thumb
The Pyroelectric infrared motion sensor can detect infrared signals from a moving person or animal, and output switching signals. It can be applied to a variety of occasions to detect the movement of human body. Conventional pyroelectric infrared sensors are much more bigger, with complex circuit and lower reliability. Now we launch this new pyroelectric infrared motion sensor, specially designed for ARDUINO. This sensor integrates a digital pyroelectric infrared sensor and connecting pins. It features higher sensibility and reliability, lower power consumption, light weight, small size, lower voltage working mode and simpler peripheral circuit.
(2)Specification:

  • Input voltage: DC 3.3V ~ 5V
  • Working current: 15uA
  • Working temperature: -20 ~ 85 degrees Celsius
  • Output voltage: high 3 V, low 0 V
  • Output delay time (high level): about 2.3 to 3 seconds
  • Detection angle: about 100 °
  • Detection distance: 3-4 meters
  • Output indicator LED (high-level )
  • Pin limit current: 100mA

Note:
1. The maximum distance is 3-4 meters during testing.
2. When testing, firstly open the white lens, you can see the rectangular sensing part. When the long line of the rectangular sensing part is parallel to the ground, the distance is the best.
3. When testing, need to cover the sensor with white lens, otherwise it will affect the distance.
4. The distance is best at 25℃, and the detection distance is shortened when it exceeds 30℃.
5. Done powering up and uploading the code, you need to wait 5-10 seconds then start testing, otherwise it is not sensitive.

(3)Component:

thumb
(4)Connection Diagram
Note: on expansion board, the pin G, V and S of PIR motion sensor are connected to G, V and 47; pin G, V and S of LED module are connected to G, V and 13.

thumb
(5)Test Code:

/*
  keyestudio smart RV
  lesson 5.1
  PIR
  http://www.keyestudio.com
*/

//PIR Motion Sensor
#define PIR  47   //PIR pin to D47  

void setup()
{
  Serial.begin(9600); //set baud rate to 9600
  pinMode(PIR, INPUT); //set the pin of PIR motion sensor to INPUT

}
void loop ()
{
  int val = digitalRead(PIR); //set the variable val to the value read
  Serial.println(val);
  delay(100); //delay in 100ms

}

(6)Test Result:

Upload code, open serial monitor and set baud rate to 9600. The serial monitor will show“1”when PIR motion sensor detects people around; on the contrary, number“0”will appear on the monitor when nobody is detected.
thumb

(7)Project Extension:

thumb

/*
  keyestudio smart RV
  lesson 5.2
  PIR
  http://www.keyestudio.com
*/

//PIR Motion Sensor
#define PIR  47   //PIR pin to D47  
#define LED  13   //LED pin to D13
void setup()
{
  pinMode(LED, OUTPUT); //set LED to OUTPUT
  pinMode(PIR, INPUT); //set PIR motion sensor to INPUT

}
void loop ()
{
  int val = digitalRead(PIR); //set val to the value read by sensor
  if (val == 1) {   //People is detected
    digitalWrite(LED, HIGH); //turn on LED
  }
  else {
    digitalWrite(LED, LOW); //otherwise, lED will be off
  }

}

The LED connected to digital 13 will be on when the sensor detects people moving, otherwise, LED will be off.

Project 6: 4*4 Membrane Keypad

(1)Description:
To save I/O ports of MCU, we make a Membrane Keypad. In this project, we will make an experiment; serial monitor will display the corresponding character when the membrane keypad is pressed.

thumb
Schematic Diagram:

thumb

(2)Specification:

  • Working Voltage: 3.3V~5V
  • Port:digital port

(3)Component:

thumb


(4)Connection Diagram:

thumb

(5)Test Code:

/*
  keyestudio smart RV
  lesson 6.1
  Keypad
  http://www.keyestudio.com
*/

#include <Keypad.h>
const byte ROWS = 4; //four rows
const byte COLS = 4; //four columns
char keypressed;
//define the cymbols on the buttons of the keypads
char keyMap[ROWS][COLS] = {
  {'1', '2', '3', 'A'},
  {'4', '5', '6', 'B'},
  {'7', '8', '9', 'C'},
  {'*', '0', '#', 'D'}
};
byte rowPins[ROWS] = {14, 15, 16, 17}; //Row pinouts of the keypad
byte colPins[COLS] = {36, 37, 38, 39}; //Column pinouts of the keypad
Keypad myKeypad = Keypad( makeKeymap(keyMap), rowPins, colPins, ROWS, COLS);

void setup()
{
  Serial.begin(9600); //set baud rate to 9600

}
void loop ()
{
  keypressed = myKeypad.getKey(); //read key value
  if (keypressed != NO_KEY) { //read key value
    Serial.print("key:"); 
    Serial.println(keypressed); //print key value
  }

}

(6)Test Result:
Download code, open serial monitor and set baud rate to 9600. The serial monitor will show the corresponding key value when the key of membrane keypad is pressed, as shown below;

thumb

Project 7: Power Amplifier Module

(1)Description:

thumb
We can use Arduino to make many interactive works of which the most commonly used is acoustic-optic display.
All the previous experiment has something to do with LED. However, the experiment of this chapter is related to produce sound. Normally, the experiment is done with a buzzer or a speaker.
In this lesson, we will replace buzzer with power amplifier module, input different frequencies square wave to emit different sound like“do re mi fa so la si do”.

(2) Specification:

  • Control interface: digital port
  • Working voltage: DC 3.3-5V

(3) Component:
thumb
(4) Connection Diagram:
Note: the pin G, V and S of passive buzzer are connected to pin G, V and D49 of expansion board

thumb
(5)Test Code:

//*************************************************************************
/*
  keyestudio smart car
  lesson 7.1
  buzzer
  http://www.keyestudio.com
*/

#define buzzer 49 //buzzer pin to D49

void setup() {
  pinMode(buzzer, OUTPUT);//set digital 49 to OUTPUT
}

void loop () {
  tone(buzzer, 262);  //buzzer emits the sound with 262Hz
  delay(250);   //delay in 250ms
  tone(buzzer, 294);;   //buzzer emits the sound with 294Hz
  delay(250);   //delay in 250ms
  tone(buzzer, 330);
  delay(250);
  tone(buzzer, 349);
  delay(250);
  tone(buzzer, 392);
  delay(250);
  tone(buzzer, 440);
  delay(250);
  tone(buzzer, 494);
  delay(250);
  tone(buzzer, 532);
  delay(250);
  noTone(buzzer);   //buzzer turns off sound output
  delay(1000);
}
//*************************************************************************************

(6) Test Result:
Upload code to MEGA 2560 smart development board, power amplifier module will emit“do re mi fa so la si do”.

(7)Project Extension:Playing Music

  /*
  keyestudio smart RV
  lesson 7.2
  buzzer
  http://www.keyestudio.com
*/

#define buzzer 49 //buzzer pin to D49

void setup() {
  pinMode(buzzer, OUTPUT);//set digital 3 to OUTPUT
}

void loop () {
  birthday();
}

////////////////////////set "Happy Birthday" Song//////////////////////////////////
void birthday()
{
  tone(buzzer, 294); //buzzer emits sound with 294Hz
  delay(250);//delay in 250ms
  tone(buzzer, 440);
  delay(250);
  tone(buzzer, 392);
  delay(250);
  tone(buzzer, 532);
  delay(250);
  tone(buzzer, 494);
  delay(500);
  tone(buzzer, 392);
  delay(250);
  tone(buzzer, 440);
  delay(250);
  tone(buzzer, 392);
  delay(250);
  tone(buzzer, 587);
  delay(250);
  tone(buzzer, 532);
  delay(500);
  tone(buzzer, 392);
  delay(250);
  tone(buzzer, 784);
  delay(250);
  tone(buzzer, 659);
  delay(250);
  tone(buzzer, 532);
  delay(250);
  tone(buzzer, 494);
  delay(250);
  tone(buzzer, 440);
  delay(250);
  tone(buzzer, 698);
  delay(375);
  tone(buzzer, 659);
  delay(250);
  tone(buzzer, 532);
  delay(250);
  tone(buzzer, 587);
  delay(250);
  tone(buzzer, 532);
  delay(500);
}

Project 8: RGB Module

(1)Description:
In the previous project, we know how to control the LED brightness.Yet, in this chapter, we will learn a special LED---- RGB. RGB LED is divided into

Common cathode means that all the cathodes are connected to a single pin. Common anode means that all the anodes are connected to a single pin. We use common anode RGB.
Common anode RGB LED has 4 pins and its anodes are interfaced with +5V. The rest of LEDs need a 220Ω resistor in cascade series to prevent circuit from burning.

We need to interface R, G and B signal ends of RGB with PWM ports of MCU. In addition, the color proportion of LED can be controlled by adjusting three PWM values, that is, LED can display different colors.
The larger corresponding color proportion is, the larger the PWM value we set.

(2)Specification:

  • Working voltage: DC 5V
  • Working current: 0.6A (maximum)
  • Maximum power: 0.3W
  • Working temperature: -25~+65℃
  • Interface: 4pin header (spacing 2.54mm)
  • Positioning hole: 3mm in diameter
  • Size: 30*20mm
  • Environmental protection attributes: ROHS

(3)Component:


thumb

(4)Connection Diagram:


thumb

(5)Test Code:

/*
  keyestudio smart RV
  lesson 8.1
  RGB
  http://www.keyestudio.com
*/

#define RGB_R  3  //define pin R of RGB as D3
#define RGB_B  4  // define pin B of RGB as D4
#define RGB_G  5  //define pin B of RGB as D5

void setup() {
  pinMode(RGB_R, OUTPUT); //set the digital ports to OUTPUT
  pinMode(RGB_G, OUTPUT);
  pinMode(RGB_B, OUTPUT);
}

void loop () {
  set_RGBColor(0,255,255);   //red
  delay(500);
  set_RGBColor(255,0,255);   //green
  delay(500);
  set_RGBColor(255,255,0);   //blue
  delay(500);
}

//set color
void set_RGBColor(int red, int green, int blue) {
  analogWrite(RGB_R, red);
  analogWrite(RGB_G, green);
  analogWrite(RGB_B, blue);
}

(6)Test Result:
After uploading code, RGB module shows red, green and blue colors.
(7)Project Extension:display random color

/*
  keyestudio smart RV
  lesson 8.2
  RGB
  http://www.keyestudio.com
*/

#define RGB_R  3  //define the pin R of RGB as D3
#define RGB_B  4  //set pin B of RGB to D4
#define RGB_G  5  //set pin g of RGB to D5
int r, g, b;
void setup() {
  pinMode(RGB_R, OUTPUT); // set digital ports of RGB to OUTPUT
  pinMode(RGB_G, OUTPUT);
  pinMode(RGB_B, OUTPUT);
}

void loop () {
  //choose a random number from 0 to 255
  r = random(255);  
  g = random(255);
  b = random(255);
  set_RGBColor(r, g, b); //random colors
  delay(500);
}

//set color
void set_RGBColor(int red, int green, int blue) {
  analogWrite(RGB_R, red);
  analogWrite(RGB_G, green);
  analogWrite(RGB_B, blue);
}

Project 9: Adjustable Rotary Potentiomete

(1)Description:
thumb
There is a rotary potentiometer module which uses a 10K adjustable resistor in this kit. By rotating the potentiometer, we can change the value of the resistor and then build the circuit to convert the resistance change into the voltage change. In addition, its voltage can be divided into 1025 parts and can be easily connected to 2560 control board.
In this chapter, we will adjust LED brightness by potentiometer.
(2)Specification:

  • Operating voltage: 3.3V to 5V
  • Interface: analog interface

(3)Component:
thumb

(4)Connection Diagram:

thumb
(5) Test Code:


/*
  keyestudio smart motorhome
  lesson 9.1
  Adjustable potentiometer
  http://www.keyestudio.com
*/
#define RES  A3   //potentiometer pin to A3
volatile int value=0;
void setup() {
  Serial.begin(9600);//set baud rate
}

void loop () {
  value = analogRead(RES);  //read the value of potentiometer
  Serial.println(value);    //print value
  delay(100);               //delay in 100MS
}

(6) Code Explanation:
1. In the project,we set pins to A3.
2. Set a integer to variable value and assign the detected result to value.
3. Serial monitor shows the value of variable value, and set baud rate to 9600.
analogRead(pin)-read the analog value of pin, mega2560 control board had 16 analog ports (A0-A15), in the range of 0~1023,that is, the accuracy is 5V/1024=0.0049V.
map(value, fromLow, fromHigh, toLow, toHigh)-value is mapped value,fromLow- current value range lower limit,fromHigh- current value range upper limit,toLow- target value range lower limit,toHigh-target value range upper limit.
(7) Test Result:
Upload code, power on with USB cable, open serial monitor and set baud rate to 9600. The serial monitor shows the corresponding analog value.
In the project, rotate the potentiometer clockwise, and the analog value increases; yet, the analog value(0-1023) decreases if rotating anticlockwise, as shown below,

thumb
(8)Project Extension:control LED brightness by potentiometer

thumb

/*
  keyestudio smart motorhome
  lesson 9.2
  Adjustable potentiometer
  http://www.keyestudio.com
*/
#define RES A3   //set potentiometer pin to A3
#define LED 13   //define the pin of LED as D13
volatile int value = 0;
void setup() {
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}

void loop () {
  value = analogRead(RES);  //read the value of potentiometer 
  int light = map(value, 0, 1023, 0, 255); //map the analog value 0~1023 of potentiometer to 0~255
  analogWrite(LED, light);   //set LED brightness to light
  delay(100);               //delay in 100MS
}

Project10: Ambient Light Sensor

(1)Description:

thumb
Ambient light sensor adopts TEMT6000 element which is a high sensitivity and visible photo sensitive (NPN type) triode. It can catch tiny light ray, amplify for 100 times and be recognized by MCU. What’s more, the reaction to light is similar to human eyes, which can determine light intensity and help create interactive appliances.

(2) Specification:

  • Working voltage: 3.3V-5V (DC)
  • Interface: 3PIN interface
  • Output signal: analog signal
  • Weight: 2.3g


thumb

(4) Connection Diagram:
Note: pin G,V and S of ambient light sensor are separately interfaced with G, V and A4; pin G, V and S of LED module are connected to G, V and 13.

thumb
(5) Test Code:

//****************************************************************************
/*
  keyestudio smart motorhome
  lesson 10.1
  photovaristor
  http://www.keyestudio.com
*/
#define photos  A4   //set photoresistance pin to A4
#define LED 13   //define the pin of LED as D13
volatile int value = 0;
void setup() {
  Serial.begin(9600);
  pinMode(LED, OUTPUT);// initialize digital pin LED as an output.
}

void loop () {
  value = analogRead(photos);  //read the value of photoresistor 
  Serial.println(value);
  if (value < 300) {  //when the analog vlaue is les than 300
    digitalWrite(LED, HIGH); //turn on LED
  }
  else {  //when the analog value is higher than 300
    digitalWrite(LED, LOW); //turn off LED
  }
  delay(100);               //delay in 100MS
}
//***************************************************************************

(6) Test Result:
Wire up, upload code and set baud rate to 9600. We see the value detected by ambient light sensor.
The value reduces when covering ambient sensor, however, LED will be on when the value is less than 300; on the contrary, LED will be off.

thumb

Project 11:Steam Sensor


thumb
(1)Description:
This is a commonly used steam sensor. Its principle is to detect the amount of water by bare printed parallel lines on the circuit board. The more the water is, the more wires will be connected. As the conductive contact area increases, the output voltage will gradually rise. It can detect water vapor in the air as well. The steam sensor can be used as a rain water detector and level switch. When the humidity on the sensor surface surges, the output voltage will increase.

The sensor is compatible with various microcontroller control boards, such as Arduino series microcontrollers. When using it, we provide the guide to operate steam sensor and Arduino control board. Connect the signal end of the sensor to the analog port of the microcontroller, sense the change of the analog value, and display the corresponding analog value on the serial monitor.
Note: the connect part is not waterproof, don’t immerse it in the water please.
(7)Specification: Working voltage: DC 3.3-5V Working current: <20mA Operating temperature range: -10℃~+70℃; Control signal: analog signal output Interface: 2.54mm 3pin pin interface Size: 35*20*8mm Weight: 2.2g 3. Pin Description:
S:signal pin output
V(+):Power(VCC)
G(-):Ground(GND)
(3) Component:

thumb
(4) Connection Diagram:
Note: on expansion board, pin G, V and S of steam sensor are connected to G, V and A2.


thumb
(6)Test Code:

//*************************************************************************
/*
  keyestudio smart motorhome 
  lesson 11.1
  water sensor
  http://www.keyestudio.com
*/
#define waterpin A5 //water sensor pin to A5
volatile int water = 0;

void setup() {
  Serial.begin(9600);

}

void loop () {
  water = analogRead(waterpin);  //read the analog value of water sensor
  Serial.println(water);
  delay(100);
}
//******************************************************************************

(7)Test Result:
Upload code, power on according to connection diagram, open serial monitor and set baud rate to 9600. The value on monitor increases when the water is on steam sensor; whereas, the value decreases when the water is wiped off.

thumb
(8)Project Extension: Power amplifier module will alarm when the water content exceeds 300

thumb

/*
  keyestudio smart motorhome
  lesson 11.2
  water sensor
  http://www.keyestudio.com
*/
#define waterpin A5 //define the pin of water sensor as A5
#define buzzer   49 //define the pin of buzzer as D49
volatile int water = 0;
void setup() {
  Serial.begin(9600);
  pinMode(buzzer, OUTPUT);//set buzzer to OUTPUT
}

void loop () {
  water = analogRead(waterpin);  //read the analog value of water sensor
  Serial.println(water);
  if (water > 300) {  //when the analog value is more than 300
    tone(buzzer,2000); //buzzer emits the sound with 2000Hz 
  }
  else {  //when the analog value is less than 300
    noTone(buzzer); //turn off buzzer
  }
  
}

Project 12 Analog Gas(MQ-2)Sensor

(1)Description:
This gas sensor is used for household gas leak alarms, industrial combustible gas alarms and portable gas detection instruments. And it is suitable for the detection of liquefied gas, benzene, alkane, alcohol, hydrogen, etc., and widely used in various fire alarm systems. The MQ-2 smoke sensor can be accurately a multi-gas detector, and has the advantages of high sensitivity, fast response, good stability, long life, and simple drive circuit. It can detect the concentration of flammable gas and smoke in the range of 300~10000ppm.Meanwhile, it has high sensitivity to natural gas, liquefied petroleum gas and other smoke, especially to alkanes smoke.

It must be heated for a period of time before using the smoke sensor, otherwise the output resistance and voltage are not accurate. However, the heating voltage should not be too high, otherwise it will cause my internal signal line to blow.
It is belongs to the tin dioxide semiconductor gas-sensitive material, and belongs to the surface ion type N-type semiconductor. At a certain temperature, tin dioxide adsorbs oxygen in the air and forms negative ion adsorption of oxygen, reducing the electron density in the semiconductor, thereby increasing its resistance value. When in contact with flammable gas in the air and smog, if the potential barrier at the grain boundary is adjusted by the smog, it will cause the surface conductivity to change. With this, information about the presence of smoke or flammable gas can be obtained. The greater the concentration of smoke or flammable gas in the air, the greater the conductivity, and the lower the output resistance, the larger the analog signal output. The sensor comes with a positioning hole, which is convenient for you to fix the sensor to other devices. In addition, the sensitivity can be adjusted by rotating the potentiometer.

(2) Specification:

  • Working voltage: 3.3-5V (DC)
  • Interface: 4 pins (GND, VCC, D0, A0)
  • Output signal: digital signal and analog signal
  • Weight: 7.5g

(3) Component:

thumb
(4) Connection Diagram:
Note: on expansion board, the pin GND, VCC, D0 and A0 of analog gas (MQ-2)sensor are interfaced with G,V, A1 and A0.

thumb
(5) Test Code:

//********************************************************************************
/*
  keyestudio smart motorhome
  lesson 12.1
  MQ2
  http://www.keyestudio.com
*/
#define MQ2_A   A0  //define the pin mq2 as A0
#define MQ2_D   A1  //define the pin mq2 as A1
volatile int analogVal,digitalVal;

void setup() {
  Serial.begin(9600);

}

void loop () {
  digitalVal = digitalRead(MQ2_D);  //read the digital value
  analogVal = analogRead(MQ2_A);  //read the analog value
  Serial.print("digitalVal:");
  Serial.print(digitalVal);
  Serial.print("  analogVal:");
  Serial.println(analogVal);
  delay(100);

}
//******************************************************************************

(6) Test Result:
Wire up, upload code and open serial monitor to set baud rate to 9600.
The analog value increases and digital level varies from 1 to 0 when the combustible gas is detected.

thumb
(7) Project Extension:
Power amplifier module will alarm when the detected combustible gas is leaked.

thumb

/*
  keyestudio smart motorhome
  lesson 12.2
  MQ2
  http://www.keyestudio.com
*/
#define MQ2_A   A0  // define MQ2_A as A0
#define MQ2_D   A1  //define MQ2_A as A1
#define buzzer  49 //buzzer pin to D49
volatile int analogVal, digitalVal;

void setup() {
  Serial.begin(9600);

}

void loop () {
  analogVal = analogRead(MQ2_A);  //read the analog value
  Serial.println(analogVal);      //print the value of sensor
  if (analogVal > 150) {          //when analog value exceeds 150, the buzzer will alarm
    tone(buzzer, 1000);
  }
  else {
    noTone(buzzer); //turn off buzzer
  }
  delay(100);

}

Project 13 DHT11 Temperature and Humidity Sensor


thumb
This DHT11 Temperature and Humidity Sensor is a composite sensor which contains a calibrated digital signal output of the temperature and humidity.Its technology ensures high reliability and excellent long-term stability. A high-performance 8-bit microcontroller is connected.This sensor includes a resistive element and a sense of wet NTC temperature measuring devices. It has excellent quality, fast response, anti-interference ability and high cost performance advantages.Each DHT11 sensor features extremely accurate calibration data of humidity calibration chamber. The calibration coefficients stored in the OTP program memory, internal sensors detect signals in the process, and we should call these calibration coefficients.The single-wire serial interface system is integrated to make it quick and easy. Qualities of small size, low power, and 20-meter signal transmission distance make it a wide applied application or even the most demanding one.

(2) Specification:

  • Supply Voltage: +5 V
  • Temperature range: 0-50 ℃ error of ± 2 ℃
  • Humidity: 20-90% RH ± 5% RH error
  • Interface: Digital


(3) Component:

thumb
(8)Connection Diagram:

thumb
In the project, we need to import the library of DHT11.
(9)Test Code:

/*
  keyestudio smart motorhome
  lesson 13.1
  DHT11
  http://www.keyestudio.com
*/
#include <dht11.h>  //include the library code:
dht11 DHT;
#define DHT11_PIN 47 //define DHT11 as 48

void setup() {
  Serial.begin(9600);

}

void loop () {
  int chk;
  chk = DHT.read(DHT11_PIN);    // READ DATA
  switch (chk) {
    case DHTLIB_OK:
      break;
    case DHTLIB_ERROR_CHECKSUM:
      break;
    case DHTLIB_ERROR_TIMEOUT:
      break;
    default:
      break;
  }
  // DISPLAT DATA
  Serial.print("humidity:");
  Serial.print(DHT.humidity);
  Serial.print("   temperature:");
  Serial.println(DHT.temperature);
  delay(100);
}

(10)Test Result:
Upload code, power on with USB cable,open serial monitor and the temperature and humidity data is shown below:

thumb

Project 14 Servo Control


thumb
(1)Description
Servo motor is a position control rotary actuator. It mainly consists of housing, circuit board, core-less motor, gear and position sensor. Its working principle is that the servo receives the signal sent by MCU or receiver and produces a reference signal with a period of 20ms and width of 1.5ms, then compares the acquired DC bias voltage to the voltage of the potentiometer and obtain the voltage difference output.

When the motor speed is constant, the potentiometer is driven to rotate through the cascade reduction gear, which leads that the voltage difference is 0, and the motor stops rotating. Generally, the angle range of servo rotation is 0° --180 °

The rotation angle of servo motor is controlled by regulating the duty cycle of PWM (Pulse-Width Modulation) signal. The standard cycle of PWM signal is 20ms (50Hz). Theoretically, the width is distributed between 1ms-2ms, but in fact, it's between 0.5ms-2.5ms. The width corresponds the rotation angle from 0° to 180°. But note that for different brand motor, the same signal may have different rotation angle. 

thumb
In general, servo has three line in brown, red and orange. Brown wire is grounded, red one is positive pole line and orange one is signal line.

thumb
The corresponding servo angles are shown below:
thumb
(2)Specification
Working voltage:

  • DC 4.8V ~ 6V
  • Operating angle range: about 180 ° (at 500 → 2500 μsec)
  • Pulse width range: 500 → 2500 μsec
  • No-load speed: 0.12 ± 0.01 sec / 60 (DC 4.8V) 0.1 ± 0.01 sec / 60 (DC 6V)
  • No-load current: 200 ± 20mA (DC 4.8V) 220 ± 20mA (DC 6V)
  • Stopping torque: 1.3 ± 0.01kg · cm (DC 4.8V) 1.5 ± 0.1kg · cm (DC 6V)
  • Stop current: ≦ 850mA (DC 4.8V) ≦ 1000mA (DC 6V)
  • Standby current: 3 ± 1mA (DC 4.8V) 4 ± 1mA (DC 6V)

(3) Component:
thumb
(4) Connection Diagram:
Note: The servo is connected to G (GND), V (VCC),8. The brown wire of the servo is connected to Gnd (G), the red wire is linked with 5v (V), and the orange wire is connected to digital pin 8.
Remember to connect external power due to the high current of driving motor.


thumb
(6)Test Code1:

/*
  keyestudio smart motorhome
  lesson 14.1
  servo
  http://www.keyestudio.com
*/
int servoPin = 8; //pin of servo

void setup() {
  pinMode(servoPin, OUTPUT);//set the pin of servo to OUTPUT
}
void loop() {
  servopulse(servoPin, 0);//rotate to 0°
  delay(1000);//delay 1s
  servopulse(servoPin, 90);//rotate to 900°
  delay(1000);
  servopulse(servoPin, 180);//rotate to 180°
  delay(1000);
}

void servopulse(int pin, int myangle) { //output function
  int pulsewidth = map(myangle, 0, 180, 500, 2500); //map angle to pulsewidth
  for (int i = 0; i < 10; i++) { //output pulse
    digitalWrite(pin, HIGH);//set level of servo port to HIGH
    delayMicroseconds(pulsewidth);//delay the time of pulsewidth
    digitalWrite(pin, LOW);//set the level of servo port to LOW
    delay(20 - pulsewidth / 1000);
  }
}
//**********************************************************************************

Upload code successfully, servo swings forth and back in the range of 0° 90° and 180°.

There is another guide for restraining servo---- servo library file, the following link of official website is for your reference. https://www.arduino.cc/en/Reference/Servo

(7)Test Code2:

/*
  keyestudio smart motorhome
  lesson 14.2
  servo
  http://www.keyestudio.com
*/
#include <Servo.h>  //include the library code:
Servo myservo;

void setup() {
  myservo.attach(8);  //connect servo to digital 8

}

void loop () {
  //rotate 0° to 180°
  for (int i = 0; i < 180; i++) {
    myservo.write(i);
    delay(20);
  }
  delay(1000);  //delay in 1s

  //rotate from 180° to 0°
  for (int i = 180; i > 0; i--) {
    myservo.write(i);
    delay(20);
  }
  delay(1000);  //delay in 1s
}

//********************************************************************************

(8)Test Result:
Upload code successfully and power on, servo swings in the range of 0° to 180°.

(9)Code Explanation:
Arduino comes with #include <Servo.h> (servo function and statement) The following are some common statements of the servo function:
1. attach(interface)——Set the pin of servo.
2. write(angle)——The statement to set rotation angle of servo, the angle range is from 0° to 180°.
3. read()——The statement to read angle of servo, read the command value of“write()”.
4. attached()——Judge if the parameter of servo is sent to its interface
Note: The above written format is“servo variable name, specific statement()”, for instance: myservo.attach(8)

Project 15 Ultrasonic Sensor

(1)Description:
The HC-SR04 ultrasonic sensor uses sonar to determine distance to an object like bats do. It offers excellent non-contact range detection with high accuracy and stable readings in an easy-to-use package. It comes complete with ultrasonic transmitter and receiver modules.The HC-SR04 or the ultrasonic sensor is being used in a wide range of electronics projects for creating obstacle detection and distance measuring application as well as various other applications. Here we have brought the simple method to measure the distance with Arduino and ultrasonic sensor and how to use ultrasonic sensor with Arduino.
(2) Specification:

thumb
(3) Component:

thumb
(4) The principle of ultrasonic sensor
The ultrasonic module will emit the ultrasonic waves after trigger signal. When the ultrasonic waves encounter the object and are reflected back, the module outputs an echo signal, so it can determine the distance of object from the time difference between trigger signal and echo signal. The t is the time that emitting signal meets obstacle and returns.
and the propagation speed of sound in the air is about 343m/s, therefore, distance = speed * time, because the ultrasonic wave emits and comes back, which is 2 times of distance, so it needs to be divided by 2, the distance measured by ultrasonic wave = (speed * time)/2

1.Use method and timing chart of ultrasonic module:
Setting the delay time of Trig pin of SR04 to 10μs at least, which can trigger it to detect distance.
2. After triggering, the module will automatically send eight 40KHz ultrasonic pulses and detect whether there is a signal return. This step will be completed automatically by the module.
3. If the signal returns, the Echo pin will output a high level, and the duration of the high level is the time from the transmission of the ultrasonic wave to the return.

thumb
Circuit diagram of ultrasonic sensor:

thumb
(5) Connection Diagram:

thumb
Wiring guide:

  Ultrasonic sensor            keyestudio V5 Sensor Shield 
     VCC           →                5v(V)
    Trig          →                22(S)
    Echo         →                23(S)
    Gnd          →                Gnd(G)


(6) Test Code:

/*
  keyestudio smart motorhome
  lesson 15.1
  Ultrasonic sensor
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
float dis;
void setup() {
  Serial.begin(9600);
  pinMode(EchoPin, INPUT);  // set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT

}

void loop () {
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger TrigPin at least 10us high level 
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 2 / 29.1;   //calculate distance
  delay(50);  //delay in 50ms
  Serial.print("distance: ");
  Serial.print(dis);
  Serial.println("cm");
}
//**************************************************************************

(7) Test Result: Upload code to development board, open serial monitor and set baud rate to 9600. The serial monitor shows the distance, and unit is cm. The value reduces when covering the ultrasonic sensor.
thumb
(8) Code Explanation:
int trigPin- this pin is defined to transmit ultrasonic waves, generally output.
int echoPin - this is defined as the pin of reception, generally input

cm = (duration/2) / 29.1
inches = (duration/2) / 74

We can calculate the distance by using the following formula:
distance = (traveltime/2) x speed of sound
The speed of sound is: 343m/s = 0.0343 cm/uS = 1/29.1 cm/uS
Or in inches: 13503.9in/s = 0.0135in/uS = 1/74in/uS
We need to divide the traveltime by 2 because we have to take into account that the wave was sent, hit the object, and then returned back to the sensor.

(9) Extension Practice:
We’ve known how to detect the distance, next, let’s try to control an LED with detected distance Value.
Connect an LED module at D13

thumb

/*
  keyestudio smart motorhome
  lesson 15.2
  Ultrasonic sensor
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22
const int LED = 13;  //led pin to D13
volatile int distance;
void setup() {
  Serial.begin(9600);
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
  pinMode(LED, OUTPUT);
}

void loop () {
  distance = get_distance();  //set distance to variable distance
  Serial.println(distance);
  if (distance < 10) {
    digitalWrite(LED, HIGH);
  }
  else {
    digitalWrite(LED, LOW);
  }
}

int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger TRIG at least 10us high level
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;   //calculate distance
  delay(10);  //delay in 50ms
  return dis;
}

//****************************************************************************                           

Upload the above code to development board. Do you find LED on when covering ultrasonic sensor by hand?

Project 16: 1602 LCD Display

(1)Description:

thumb
With I2C communication module, this is a display module that can show 2 lines with 16 characters per line.
It shows blue background and white word and connects to I2C interface of MCU, which highly save the MCU resources.
On the back of LCD display, there is a blue potentiometer for adjusting the backlight. The communication address defaults to 0x27.
The original 1602 LCD can start and run with 7 IO ports, but ours is built with ARDUINOIIC/I2C interface, saving 5 IO ports. Alternatively, the module comes with 4 positioning holes with a diameter of 3mm, which is convenient for you to fix on other devices.

Notice that when the screen gets brighter or darker, the characters will become more visible or less visible.

(2) Specification:

  • I2C address: 0x27
  • Backlight (blue, white)
  • Power supply voltage: 5V
  • Adjustable contrast
  • GND: A pin that connects to ground
  • VCC: A pin that connects to a +5V power supply
  • SDA: A pin that connects to analog port 20 for IIC communication
  • SCL: A pin that connects to analog port 21 for IIC communication

(3) Component:

thumb
(4) Connection Diagram:
Note: the pin GND, VCC, SDA and SCL of 1602LCD module are connected to GND(-), 5V(+), SDA and SCL.

thumb
(5) Test Code:

//**************************************************************************
/*
  keyestudio smart motorhome
  lesson 16.1
  I2C 1602
  http://www.keyestudio.com
*/
#include <Wire.h>
#include <LiquidCrystal_I2C.h> // includes the LiquidCrystal_I2C Library 
LiquidCrystal_I2C lcd(0x27, 16, 2); // set the LCD address to 0x27 for a 16 chars and 2 line display

void setup() {
  lcd.init();
  // Print a message to the LCD.
  lcd.backlight();  //set backlight
  lcd.setCursor(0,0); /set cursor at the first row and first column
  lcd.print("Hello, World!"); //display "Hello, World!"
  lcd.setCursor(0,1); //at the second row and first column
  lcd.print("Hello, Keyes!"); //show "Hello, Keyes!"
}

void loop () {
  
}
//************************************************************************

(6) Test Result:

Upload code, wire up according to connection diagram and power on. 1602 LCD will display“Hello World!”at the first row and show“Hello Keyes!”at the second row.

Note: wire up connection diagram, upload code and power on. You can adjust the potentiometer on the back of 1602LCD display module to display the character strings


Project 17: 2812 Light Strip

(1)Description:
This module is an intelligent controlled LED light source that integrates the control circuit and light-emitting circuit. Each LED shape is as same as a 5050LED bead. Each element is a pixel. Each pixel interior includes not only intelligent digital port data latch and signal reshaping amplification drive circuit, but also a precision internal oscillator and a 12V programmable constant current control part, effectively ensuring the highly consistency of the pixel point light color.

The data transfer protocol uses single RZ (return-to-zero) communication mode. After the pixel power-on to reset, the DI port receives data from controller, the first 24bit data is extracted by the first pixel, and then sent to the data latch inside the pixel. After being amplified by the internal shaping processing circuit, the remaining data will be forwarded to the next cascade pixel point through the DO port of the LED.
The signal will be reduced by 24bit for each pixel point transmission.
The pixel point adopts automatic transfer technology so that the number of cascade pixel are only limited by signal transmission speed rather than signal transmission.


(2)Specification:

  • LED: WS2812
  • Working voltage: DC 5V
  • Working current: 40mA*10*2=8000mA (maximum) (each RGB lamp current 40mA)
  • Wiring mode: G-GND V-VCC (DC 5V) DI (signal input terminal) DO (signal output terminal, used in cascade connection)

(3)Component:

thumb
(4) Connection Diagram:
Note: the pin GND, VCC and DI of 8x16 LED panel are interfaced with the pin -(GND), +(VCC)and 53 of sensor expansion board.

thumb
(5) Test Code

/*
  keyestudio smart motorhome
  lesson 17.1
  2812 led
  http://www.keyestudio.com
*/
#include <Adafruit_NeoPixel.h>
Adafruit_NeoPixel rgb_2812 = Adafruit_NeoPixel(10, 53, NEO_GRB + NEO_KHZ800); //dset the port of 10 pcs lights to 53, with GRB mode

void setup() {
  rgb_2812.begin();
}

void loop () {

  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,255,0,0);  //the first light shows red color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);   //the first light turns off
    rgb_2812.show();                    //show
    delay(50);
  }

  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,0,255,0);  //the first light shows green color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);   //the first light turns off
    rgb_2812.show();                    //display
    delay(50);
  }

  for (int i = 0; i <= 9; i++) {
    rgb_2812.setPixelColor(i,0,0,255);  //the first light shows blue color
    rgb_2812.show();                    //show
    delay(50);
  }
  for (int i = 9; i >= 0; i--) {
    rgb_2812.setPixelColor(i, 0,0,0);   //the first light turns off
    rgb_2812.show();                    //show
    delay(50);
  }

}

(6) Test Result:
Upload code and power on. 2812 light strip shows red, green and blue color.

(7) Project Extension:show gradient colour

/*
  keyestudio smart motorhome
  lesson 17.2
  2812 led
  http://www.keyestudio.com
*/
#include <Adafruit_NeoPixel.h>
Adafruit_NeoPixel rgb_2812 = Adafruit_NeoPixel(10, 53, NEO_GRB + NEO_KHZ800); //set the port of 10 pcs lights to 53, with GRB mode

void setup() {
  rgb_2812.begin();
}

void loop () {
  rainbow(20);  //keep gradient color for 20ms

}

void rainbow(uint8_t wait) {
  uint16_t i, j;
  for (j = 0; j < 256; j++) {
    for (i = 0; i <= 9; i++) {
      rgb_2812.setPixelColor(i, Wheel((i + j) & 255));
    }
    rgb_2812.show(); //display
    delay(wait);
  }
}

uint32_t Wheel(byte WheelPos) { //set color
  if (WheelPos < 85) {
    return rgb_2812.Color(WheelPos * 3, 255 - WheelPos * 3, 0);
  }
  else if (WheelPos < 170) {
    WheelPos -= 85;
    return rgb_2812.Color(255 - WheelPos * 3, 0, WheelPos * 3);
  }
  else {
    WheelPos -= 170;
    return rgb_2812.Color(0, WheelPos * 3, 255 - WheelPos * 3);
  }
}

Project 18 Motor Driving and Speed Control

(1)Description:

There are many ways to drive the motor. Our robot car uses the most commonly used TB6612FNG. TB6612FNG is an excellent high-power motor driver IC produced by STMicroelectronics.
It has large current MOSFET-H bridge structure and can directly drive two motors simultaneously. We apply the design of TB6612FNG circuit to development board, which reduces the technical difficulty of using and driving the motor.


Schematic Diagram

thumb
(2)Specification

  • Logic part input voltage: DC5V
  • Driving part input voltage: DC 7-12V
  • Working temperature: -20~85℃
  • Power supply voltage: VM = 15V max, VCC = 2.7-5.5V
  • Output current: Iout = 1.2A (average) / 3.2A (peak)
  • Standby control to save power Clockwise/counterclockwise/short brake/stop motor control mode
  • Built-in thermal shutdown circuit and low voltage detection circuit
  • Filter capacitors on two power lines


(3)Working Principle

According to the above diagram of motor driver board, we know that speed control pins of motor A, B, C and D are D12, D11, D9 and D10; in the meanwhile, their direction control pins are D35 and D34, D33 and D32, D29 and D28, D31 and D30.
In the following chart, we also know how to control the speed of four motors via digital and PWM ports
PWM value is in the range of 0-255, the larger the number we set, the faster the motor rotates. (We will drive a motor, therefore, speeds can be set a value in 0~255)

thumb
(4)Component:

thumb
(5) Connection Diagram:

thumb
(6) Test Code:

/*
  keyestudio smart motorhome
  lesson 18.1
  motor
  http://www.keyestudio.com
*/
//define the pins of motor
const int Motor1 = 31;
const int Motor2 = 30;
const int PWM = 10;

void setup() {
  //set ports of motor to OUTPUT
  pinMode(Motor1, OUTPUT);
  pinMode(Motor2, OUTPUT);

}

void loop () {
  //rotate anticlockwise for 1
  digitalWrite(Motor1, HIGH);
  digitalWrite(Motor2, LOW);
  analogWrite(PWM, 100);
  delay(2000);
  //rotate clockwise for 1s
  digitalWrite(Motor1, LOW);
  digitalWrite(Motor2, HIGH);
  analogWrite(PWM, 100);
  delay(2000);
  //stop 1s
  analogWrite(PWM, 0);
  delay(1000);
}
//*****************************************************************************

(7) Test Result:
Upload code and power on. The motor rotates clockwise for 2s, anticlockwise for 2s and stops for 1s.

(12)Code Explanation:
digitalWrite(Motor,LOW); the rotation direction of motor is decided by the high/low level and and the pins that decide rotation direction are digital pins.

analogWrite(PWM,100); the speed of motor is regulated by PWM, and the pins that decide the speed of motor must be PWM pins.

(9) Extension Practice:
Control car’s motion via rotation direction of motors.

/*
  keyestudio smart motorhome
  lesson 18.2
  motor
  http://www.keyestudio.com
*/
//define the pins of motor A,B,C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

void setup() {
  //set the pins of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);

}

void loop () {
  //go forward for 1s
  advance();
  delay(1000);
  //go back for 1s
  back();
  delay(1000);
  //turn left for 1s
  turnleft();
  delay(1000);
  //turn right for 1s
  turnright();
  delay(1000);
  //stop 1s
  Stop();
  delay(1000);
}

void advance() {    //go forward
  // motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, 150);
  //motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, 150);
  //motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, 150);
  //motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, 150);
}

void back() {   //go back
  //motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, 150);
  //motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, 150);
  //motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, 150);
  //motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, 150);
}

void turnleft() {   //turn left
  //motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, 150);
  //motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, 150);
  //motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, 150);
  //motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, 150);
}

void turnright() {    //turn right
  //motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, 150);
  //motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, 150);
  //motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, 150);
  //motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, 150);
}

void Stop() {   //Car stops
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//***********************************************************************

Upload code and power on. The car goes forward 1s, back for 1s, turns left for 1s and right for 1s, then stops.

Project 19 Bluetooth Remote Control

(1)Description:

Bluetooth, a simple wireless communication module most popular since the last few decades and easy to use are being used in most of the battery-powered devices.

thumb

Over the years, there have been many upgrades of Bluetooth standard to keep fulfil the demand of customers and technology according to the need of time and situation.
Over the few years, there are many things changed including data transmission rate, power consumption with wearable and IoT Devices and Security System.
Here we are going to learn about HM-10 BLE 4.0 with Arduino Board. The HM-10 is a readily available Bluetooth 4.0 module. This module is used for establishing wireless data communication. The module is designed by using the Texas Instruments CC2540 or CC2541 Bluetooth low energy (BLE) System on Chip (SoC).

(2) Specification :

  • Bluetooth protocol: Bluetooth Specification V4.0 BLE
  • No byte limit in serial port Transceiving
  • In open environment, realize 100m ultra-distance communication with iphone4s
  • Working frequency: 2.4GHz ISM band
  • Modulation method: GFSK(Gaussian Frequency Shift Keying)
  • Transmission power: -23dbm, -6dbm, 0dbm, 6dbm, can be modified by AT command.
  • Sensitivity: ≤-84dBm at 0.1% BER
  • Transmission rate: Asynchronous: 6K bytes ; Synchronous: 6k Bytes
  • Security feature: Authentication and encryption
  • Supporting service: Central & Peripheral UUID FFE0, FFE1
  • Power consumption: Auto sleep mode, stand by current 400uA~800uA, 8.5mA during transmission.
  • Power supply: 5V DC
  • Working temperature: –5 to +65 Centigrade

(3) Component:

thumb
(4) Connection Diagram:
1. STATE: state test pins, connected to internal LED, generally keep it unconnected.
2. RXD: serial interface, receiving terminal.
3. TXD: serial interface, transmitting terminal.
4. GND: Ground.
5. VCC: positive pole of the power.
6. EN/BRK: break connect, it means breaking the Bluetooth connection, generally, keep it unconnected.

thumb

  (Notice Serial and Serial1)

(5) Test Code:

/*
  keyestudio smart motorhome
  lesson 19.1
  bluetooth
  http://www.keyestudio.com
*/
char ble_val;   //set variable ble_val

void setup() {
  Serial.begin(9600);   //set USB baud rate to 9600
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
}

void loop () {
  if (Serial1.available() > 0) // determine if there is data in the buffer of serial port
  { 
    ble_val = Serial1.read();  //read the data saved in the buffer of serial port
    Serial.println(ble_val);  //serial port prints data
  }
}

//**********************************************************************

Upload code to development board and insert Bluetooth module and wait for the command from cellphone.

(6) Download APP:
The above code is used to read the received signals. Yet, we need to send signals.
Next, we download an App to send signals.


iOS System

1.Open App store 2.Search Motorhome and download it.


thumb thumb


The App page is shown below:


thumb

Turn on Bluetooth of your device, and click “connect” to search and pair Bluetooth.

thumb


Android System

Enter Google play store to search keyestudio motorhome, or go to link to download it : https://play.google.com/store/apps/details?id=com.keyestudio.motorhome

thumb

thumb thumb


Note: Allow APP to access“location”in settings of your cellphone when connecting to Bluetooth module, otherwise, Bluetooth may not be connected.

Click thumb icon to enter APP, as shown below;


thumb

After connecting Bluetooth, plug in power and LED indicator of Bluetooth module will flash. Tapthumb to search Bluetooth.



thumb

Click “connect” below HMSoft, then the Bluetooth will be connected and its LED indicator will be always on.


thumb

After connecting Bluetooth module and opening serial monitor and setting baud rate to 9600. Press icons on APP, and the corresponding characters are displayed as shown below:


thumb

(7) Code Explanation:
Serial.available():the number of left characters when back to buffer, this function is usually used to judge if there is data in buffer. Whenever Serial.available() is more than 0, serial will receive the data in serial monitor.
Serial.read(): read a Byte in buffer of serial. We can read the data sent with Serial.read(), for instance, some devices send data to Arduino through serial monitor.

Note: We use Serial and Serial1. Serial is used for Arduino monitor communication and Serial 1 is used for Bluetooth serial.
(8) APP Interface:
Open App and we will see its main interface as follows:

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb
The motorhome will emit the corresponding sound when pressing“do,re,mi,fa,so,la,si.” (9) Extension Practice:
Next, we will turn on and off LED via Bluetooth commands.
Note: Allow APP to access“location”in settings of your cellphone when connecting to Bluetooth module, otherwise, Bluetooth may not be connected.


thumb

//*************************************************************************
/*
  keyestudio smart motorhome
  lesson 19.2
  bluetooth
  http://www.keyestudio.com
*/
char ble_val;   //set variable to ble_val
#define LED    13    //led pin to D13
void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  pinMode(LED, OUTPUT); //set the pin of LED to OUTPUT

}

void loop () {
  if (Serial1.available() > 0) //determine if there is data in the buffer of Bluetooth serial port
  {
    ble_val = Serial1.read();  //read the data saved in the buffer of Bluetooth serial port
    if (ble_val == 'A') {
      digitalWrite(LED, HIGH);
    }
    else if (ble_val == 'H') {
      digitalWrite(LED, LOW);
    }
  }
}
//*************************************************************************

Click“Write”on app to send“F”or“B” to control LED.

Project 20: Install Smart Motorhome


thumb

thumb

thumb

thumb


thumb

Connection Diagram


thumb

Test Code

#include <Servo.h>
Servo myservo1,myservo2,myservo3;  // create servo object to control a servo

void setup()
{
  Serial.begin(9600); 
myservo1.attach(6);  // modify each pin to adjust 
myservo2.attach(7);  // modify each pin to adjust 
myservo3.attach(8);  // modify each pin to adjust 
  myservo1.write(80);  // angle value  
  delay(1000);
myservo2.write(0);  // angle value  
  delay(1000);
myservo3.write(0);  // angle value  
  delay(1000);
}

void loop() 
{
}

Test Result

Interface servo with D6, D7 and D8 of board, upload code and wire up. Plug in power and press reset button, servo will automatically rotate the initial angle we set.



Components Components
Installation Steps
Part 1

thumb

thumb
  Install button sensor on the number 19 area of board B 

thumb

Mount power amplifier module at the number 4 area of board B,and rotate the potentiometer to the middle area.


thumb

Initialize servo2 and fix it on the number 5 area of board B and notice the direction.


thumb

Fix the cross mount on the board H


thumb

Use M2*4 screws from servo and mount board H onto servo.


thumb

Install LED strip at the number 21 of board B.


thumb
Part 2

thumb

thumb

Mount gas sensor at number 3 area of board A


thumb

Assemble PIR motion sensor at number 2 of board A


thumb

Install LED strip at number 20 area of board A


thumb

Fix 4*4 membrane keypad onto number 1 area of board A


thumb

Assemble board I on board A


thumb
Part 3

thumb

thumb
                  Wire up first

thumb

Install ultrasonic sensor onto number 8 area of board K


thumb
                     Wire up first

thumb

Install the full-color LED module onto number 9 and 10 area of board K


thumb
Part 4
Components


thumb


thumb

Mount the LCD display onto number 11 area of board L


thumb
Part 5

thumb

thumb

Respectively assemble rotary potentiometer and steam sensor at number 16 area and number 17 of board N


thumb

Initialize servo 1 and install it at number 19 area of board N


thumb

Fix servo cross mount onto gear of roof window with M2*4MM screws from servo


thumb

Install board O onto board N and don’t need to screw nuts tightly.


thumb
Part 6

thumb

thumb

Respectively install temperature humidity sensor and ambient light sensor at number 14 area and number 15 area of board M.


thumb

Fix white LED module onto number 12 area of board M


thumb

Adjust the angle of servo 3 and install it onto number 13 area.


thumb

Fix servo cross onto board E


thumb

Use M2*4MM screws from servo to install board E onto servo


thumb

Fix control board onto M board


thumb
Part 7

thumb

thumb

Assemble motor parts onto board C


thumb

Install motors onto board and notice the direction of motors


thumb

thumb

Install the wheels onto motor


thumb

Assemble battery holder onto number 7 area of board C


thumb

Mount line tracking sensor onto number 6 area of board C


thumb
Part 8
Be patient please when you have difficulty in inserting them.

thumb

Use the bigger slots to install


thumb

Use the bigger slots to install


thumb

Make the side marked letters on board G face upward


thumb

Make the side marked letters on board P face forward


thumb

thumb

Be careful to install board because its protruding part is weak.


thumb

You need to remove board E, then install board F and slot.


thumb

thumb

thumb

thumb

thumb
Wiring Up
According to diagram to wire up


thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb

thumb
Note: be careful to mount board because its protruding part is weak.
thumb

thumb

thumb

Project 21: Line Tracking Motorhome


thumb
(1)Description:
We’ve introduced how to work with sensors and modules. In this part, we will integrate some modules to finish more complex program. Next, we will make a line tracking smart motorhome.

thumb
Flow Chart

thumb
(2)Connection Diagram

thumb
(3)Test Code

/*
  keyestudio smart motorhome
  lesson 21
  Tracking motorhome
  http://www.keyestudio.com
*/
//Line Tracking Sensor
#define L_pin  50
#define M_pin  51
#define R_pin  52

//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

volatile int speeds = 120;  //define the speed variable speeds
void setup() {
  pinMode(L_pin, INPUT); //set the pins of line tracking sensor to INPUT
  pinMode(M_pin, INPUT);
  pinMode(R_pin, INPUT);

  //set ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}

void loop () {
  int L_val = digitalRead(L_pin); //read the value of left sensor
  int M_val = digitalRead(M_pin); //read the value of middle sensor
  int R_val = digitalRead(R_pin); //read the value of right sensor
  if (M_val == 1) { //the middle one detects black line
    if (L_val == 1 && R_val == 0) { //if only left sensor detects black line, turn left
      turnleft();
    }
    else if (L_val == 0 && R_val == 1) { //if only right sensor detects black line, turn right
      turnright();
    }
    else { //go forward
      advance();
    }
  }
  else { //the middle sensor detects black line
    if (L_val == 1 && R_val == 0) { //if only left sensor detects black line, turn left
      turnleft();
    }
    else if (L_val == 0 && R_val == 1) { //if only right sensor detects black line,turn right
    }
    else { //stop
      Stop();
    }
  }
  
}

void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void back() {   //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void turnleft() {   //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void Stop() {   //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//*******************************************************************************


(4)Test Result
Upload code to development board and power on. The smart motorhome runs along black tracks. However, if it deviates from the track, the RV can automatically adjust back.

Project 22: Ultrasonic Follow Motorhome


thumb
(1) Description: In this lesson, we will make an ultrasonic follow motorhome based on the working principle of ultrasonic sensor. The ultrasonic sensor detects the distance between obstacle and car. Then we will drive motorhome to move through the distance value.

thumb
Flow Chart
thumb
(3) Connection Diagram

thumb
(4) Test Code

/*
  keyestudio smart motorhome
  lesson 22
  flowing motorhome
  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22

//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

volatile int speeds = 120;  //define the speed variable speeds
volatile int distance;
void setup() {
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}

void loop () {
  distance = get_distance();
  if (distance <= 8) {
    back();
  }
  else if (distance > 8 && distance <= 15) {
    Stop();
  }
  else if (distance > 15 && distance <= 35) {
    advance();
  }
  else {
    Stop();
  }
  
}

int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger at least 10us high level to TRIG
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;  //calculate the distance
  delay(10);
  return dis;
}
  
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void back() {   //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void turnleft() {   //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void Stop() {   //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//***********************************************************************************************

(5) Test Result Upload code to development board and wire up according to connection diagram. The smart motorhome will follow the obstacle to move.



=== Project 23: Ultrasonic Obstacle Avoidance Motorhome ===
<br>[[File:0507--图片67.png|500px|frameless|thumb]]<br>
(1)Description:<br>
In previous lesson, we made a follow smart motorhome. Equally, we can transform it into ultrasonic obstacle avoidance motorhome through code. Let’s get started.<br>
<br>[[File:0507--图片68.png|500px|frameless|thumb]]<br>
Flow Chart<br>
<br>[[File:0507--图片69.png|500px|frameless|thumb]]<br>
(2)Connection Diagram<br>
<br>[[File:0507--图片70.png|500px|frameless|thumb]]<br>
(3)Test Code
<pre>
/*
  keyestudio smart motorhome
  lesson 23
  avoiding motorhome  http://www.keyestudio.com
*/
//Ultrasonic Sensor
#define EchoPin  23  //ECHO to D23
#define TrigPin  22  //TRIG to D22

//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

volatile int speeds = 120;  //define the speed variable speeds
volatile int distance;
void setup() {
  pinMode(EchoPin, INPUT);  //set pin ECHO to INPUT
  pinMode(TrigPin, OUTPUT);  //set pin TRIG to OUTPUT

  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}

void loop () {
  distance = get_distance();  //set the distance to variable distance
  if (distance < 8) {
    back();
    delay(300);
  }
  else if (distance < 15) {
    turnleft();
    delay(300);
  }
  else {
    advance();
  }
  
}

int get_distance() {  //detect distance by ultrasonic sensor
  int dis;
  digitalWrite(TrigPin, LOW);
  delayMicroseconds(2);
  digitalWrite(TrigPin, HIGH);  //trigger at least 10us high level to TRIG
  delayMicroseconds(10);
  digitalWrite(TrigPin, LOW);
  dis = pulseIn(EchoPin, HIGH) / 58;  //计calculate the distance
  delay(10);
  return dis;
}
  
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void back() {   //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void turnleft() {   //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void Stop() {   //stop
  //set the speed of four motors to 
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}

(4)Test Result
Upload code successfully, power on and smart motorhome goes forward. It can avoid the obstacle when meeting obstacle


Project 24: Bluetooth Control motorhome


thumb
(1) Description:
We’ve learned the basic knowledge of Bluetooth, in this lesson, we will make a Bluetooth smart motorhome. In the experiment, we default the HM-10 Bluetooth module as a Slave and the cellphone as a Host.
Then install an App and connect to HM-10 Bluetooth module so as to control smart motorhome. Next, let’s control it through the key value of App.

Note: pin RXD1, TXD1, GND and VCC of Bluetooth module are interfaced with pin TX1, RX1, -(GND)and +(VCC)of mega2560 control board. Pin STATE and BRK don’t need connecting and BAT is connected to power.


The corresponding key values are shown below:

thumb
Flow Chart:
thumb
(3) Connection Diagram

thumb
(4) Test Code

/*
  keyestudio smart motorhome
  lesson 24.1
  Bluetooth control motorhome
  http://www.keyestudio.com
*/

//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

volatile int speeds = 120;  //define the speed variable speeds
char ble_val;   //set variable ble_val
void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}

void loop () {
  if (Serial1.available() > 0) //serial port reads characters
  {
    ble_val = Serial1.read();//set the character read by serial port to val
      case 'F':  advance();    break;
      case 'B':  back();       break;
      case 'L':  turnleft();   break;
      case 'R':  turnright();  break;
      case 'S':  Stop();       break;
    }
  }
  
}
  
void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void back() {   //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void turnleft() {   //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void Stop() {   //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}
//*********************************************************************************************

(2)Test Result  
Upload code to development board, insert Bluetooth module, open App and connect Bluetooth. The smart motorhome reacts the corresponding action by pressing icons on the app


(6) Project Extension:adjust speed via App
/*
  keyestudio smart motorhome
  lesson 24.2
  Bluetooth control motorhome
  http://www.keyestudio.com
*/

//define the pins of motor A, B, C and D
const int MA1 = 35;
const int MA2 = 34;
const int PWMA = 12;

const int MB1 = 33;
const int MB2 = 32;
const int PWMB = 11;

const int MC1 = 29;
const int MC2 = 28;
const int PWMC = 9;

const int MD1 = 31;
const int MD2 = 30;
const int PWMD = 10;

volatile int speeds = 120;  //define the speed variable speeds
char ble_val;   //set variable ble_val

void setup() {
  Serial1.begin(9600);  //set Bluetooth baud rate to 9600
  Serial.begin(9600);
  //set the ports of motor to OUTPUT
  pinMode(MA1, OUTPUT);
  pinMode(MA2, OUTPUT);

  pinMode(MB1, OUTPUT);
  pinMode(MB2, OUTPUT);

  pinMode(MC1, OUTPUT);
  pinMode(MC2, OUTPUT);

  pinMode(MD1, OUTPUT);
  pinMode(MD2, OUTPUT);
}

void loop () {
  if (Serial1.available() > 0) //serial port reads characters
  {
    ble_val = Serial1.read();//set the character read by serial port to val
    switch (ble_val) {
      case 'F':  advance();    break;
      case 'B':  back();       break;
      case 'L':  turnleft();   break;
      case 'R':  turnright();  break;
      case 'S':  Stop();       break;
      case  'W':  speeds_a();  break;  //receive ‘W’, speed up
      case  'Z':  speeds_d();  break; //receive "Z", speed down
    }
  }
  
}

void speeds_a() { //increment function
  int a_flag = 1; //used for while loop
  while (a_flag) {
    Serial.println(speeds);  //display velocity
    if (speeds < 255) { //increase to 255(MAX)
      speeds++;
      delay(15);  //adjust the rate of acceleration
    }
    ble_val = Serial1.read();
    if (ble_val == 'S')a_flag = 0; //receive‘S’, stop speeding up
  }
}

void speeds_d() { //Deceleration function
  int d_flag = 1; //used for while loop
  while (d_flag) {
    Serial.println(speeds);  //display speed
    if (speeds > 0) { //decrease to 0
      speeds--;
      delay(15);    //adjust the rate of deceleration
    }
    ble_val = Serial1.read();
    if (ble_val == 'S')d_flag = 0; //receive ‘S’and stop speeding down
  }
}

void advance() {    //go forward
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void back() {   //go back
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void turnleft() {   //turn left
  //Motor A rotates clockwise
  digitalWrite(MA1, HIGH);
  digitalWrite(MA2, LOW);
  analogWrite(PWMA, speeds);
  //Motor B rotates anticlockwise
  digitalWrite(MB1, HIGH);
  digitalWrite(MB2, LOW);
  analogWrite(PWMB, speeds);
  //Motor C rotates anticlockwise
  digitalWrite(MC1, HIGH);
  digitalWrite(MC2, LOW);
  analogWrite(PWMC, speeds);
  //Motor D rotates clockwise
  digitalWrite(MD1, HIGH);
  digitalWrite(MD2, LOW);
  analogWrite(PWMD, speeds);
}

void turnright() {    //turn right
  //Motor A rotates anticlockwise
  digitalWrite(MA1, LOW);
  digitalWrite(MA2, HIGH);
  analogWrite(PWMA, speeds);
  //Motor B rotates clockwise
  digitalWrite(MB1, LOW);
  digitalWrite(MB2, HIGH);
  analogWrite(PWMB, speeds);
  //Motor C rotates clockwise
  digitalWrite(MC1, LOW);
  digitalWrite(MC2, HIGH);
  analogWrite(PWMC, speeds);
  //Motor D rotates anticlockwise
  digitalWrite(MD1, LOW);
  digitalWrite(MD2, HIGH);
  analogWrite(PWMD, speeds);
}

void Stop() {   //stop
  //set the speed of four motors to 0
  analogWrite(PWMA, 0);
  analogWrite(PWMB, 0);
  analogWrite(PWMC, 0);
  analogWrite(PWMD, 0);
}

Upload code, power on and connect to App. The speed is increasing to 255 when the speed-up button is pressed, however, speed is reducing to 0 when the speed-down button is pressed. As shown below:

thumb

Project 25: Multi-purpose Smart Motorhome

In this chapter, we will test the function of smart motorhome via App. And we combine all functions together to make motorhome perform them.
Next we will make a comprehensive flow chart, test the wiring-up and upload code to make a multi-purpose smart motorhome.

For this comprehensive project, you can download tutorial in the link: https://fs.keyestudio.com/KS0507