Ks0001 keyestudio UNO R3 BOARD: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
No edit summary
No edit summary
Line 3: Line 3:
Keyestudio Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.<br>
Keyestudio Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.<br>
The Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 programmed as a USB-to-serial converter.].<br>
The Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 programmed as a USB-to-serial converter.].<br>
[[FileSL)AI-LP97(@OPQP068CN-L.png]]
[[File:SL)AI-LP97(@OPQP068CN-L.png]]


== Features  ==
== Features  ==

Revision as of 14:55, 10 August 2016

Introduction

Keyestudio Uno R3 is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
The Uno R3 differs from all preceding boards in that it does not use the FTDI USB-to-serial driver chip. Instead, it features the Atmega16U2 programmed as a USB-to-serial converter.].
File:SL)AI-LP97(@OPQP068CN-L.png

Features

1.0 pinout: added SDA and SCL pins that are near to the AREF pin and two other new pins placed near to the RESET pin, the IOREF that allow the shields to adapt to the voltage provided from the board. In future, shields will be compatible with both the board that uses the AVR, which operates with 5V and with the Arduino Due that operates with 3.3V. The second one is a not connected pin, that is reserved for future purposes. Stronger RESET circuit. Atmega 16U2 replace the 8U2.

Cautions

The warnings and wrong operations possible cause dangerous.

Schematic

  1. File:BUGduinoSchematicPDF.pdf

Specifications

Microcontroller: ATmega328
OperatingVoltage: 5V
Input Voltage (recommended): 7-12V
Input Voltage (limits): 6-20V
Digital I/O Pins: 14 (of which 6 provide PWM output)
Analog Input Pins: 6
DC Current per I/O Pin: 20 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 32 KB (ATmega328) of which 0.5 KB used by bootloader
SRAM: 2 KB (ATmega328)
EEPROM: 1 KB (ATmega328)
Clock Speed: 16 MHz
Length: 68.6 mm
Width: 53.4 mm
Weight: 25 g


Pin definition and Rating

Usage

Download the Arduino environment

Get the latest version from the download page. When the download finishes, unzip the downloaded file. Make sure to preserve the folder structure. Double-click the folder to open it. There should be a few files and sub-folders inside.

Connect the board

The Arduino Uno, Mega, Duemilanove and Arduino Nano automatically draw power from either the USB connection to the computer or an external power supply. If you're using an Arduino Diecimila, you'll need to make sure that the board is configured to draw power from the USB connection. The power source is selected with a jumper, a small piece of plastic that fits onto two of the three pins between the USB and power jacks. Check that it's on the two pins closest to the USB port. Connect the Arduino board to your computer using the USB cable. The green power LED (labelled PWR) should go on.

Install the drivers

Installing drivers for the Arduino Uno or Arduino Mega 2560 with Windows 7, Vista, or XP: Plug in your board and wait for Windows to begin it's driver installation process. After a few moments, the process will fail, despite its best efforts Click on the Start Menu, and open up the Control Panel. While in the Control Panel, navigate to System and Security. Next, click on System. Once the System window is up, open the Device Manager. Look under Ports (COM & LPT). You should see an open port named "Arduino UNO (COMxx)". If there is no COM & LPT section, look under "Other Devices" for "Unknown Device". Right click on the "Arduino UNO (COmxx)" port and choose the "Update Driver Software" option. Next, choose the "Browse my computer for Driver software" option. Finally, navigate to and select the driver file named "arduino.inf", located in the "Drivers" folder of the Arduino Software download (not the "FTDI USB Drivers" sub-directory). If you are using an old version of the IDE (1.0.3 or older), choose the Uno driver file named "Arduino UNO.inf" Windows will finish up the driver installation from there. See also: step-by-step screenshots for installing the Uno under Windows XP. Installing drivers for the Arduino Duemilanove, Nano, or Diecimila with Windows7, Vista, or XP: When you connect the board, Windows should initiate the driver installation process (if you haven't used the computer with an Arduino board before). On Windows Vista, the driver should be automatically downloaded and installed. (Really, it works!) On Windows XP, the Add New Hardware wizard will open: When asked Can Windows connect to Windows Update to search for software? select No, not this time. Click next. Select Install from a list or specified location (Advanced) and click next. Make sure that Search for the best driver in these locations is checked; uncheck Search removable media; check Include this location in the search and browse to the drivers/FTDI USB Drivers directory of the Arduino distribution. (The latest version of the drivers can be found on the FTDI website.) Click next. The wizard will search for the driver and then tell you that a "USB Serial Converter" was found. Click finish. The new hardware wizard will appear again. Go through the same steps and select the same options and location to search. This time, a "USB Serial Port" will be found. You can check that the drivers have been installed by opening the Windows Device Mananger (in the Hardware tab of System control panel). Look for a "USB Serial Port" in the Ports section; that's the Arduino board.


Programming

<syntaxhighlight lang="arduino">

  1. include <Wire.h>

//SLOTS: Vendor: 0x02 //SLOTS: Product 0x10 //SLOTS: Revision 0x20 //A0-->GND, A1-->GND, A2-->GND

  1. define AT24C02B_Addr 0b1010000

unsigned char bugduino_signature[]= {

 0x00,0x00,0x02,0x00,0x10,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0b,0x16,0x00,0x00,0x00,0x0f

}; unsigned char address_map[]= {

 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,0x7f

};

void setup() {

 Wire.begin();
 Serial.begin(38400);

} void loop() {

 /* 
  */
 unsigned char i = 0;
 unsigned char eeprom = 0;
 for(i=0;i<20;i++)
 {  
   Wire.beginTransmission(AT24C02B_Addr); //start
   Wire.send(address_map[i]);
   Wire.endTransmission();    //stop
   Wire.requestFrom(AT24C02B_Addr, 1);    // request
   delay(1);
   while(Wire.available())    // slave may send less than requested
   { 
     unsigned char c = Wire.receive(); // receive a byte as character
     if(c != bugduino_signature[i])
     {
       eeprom =1;
     }
   }
 }
 delay(100);
 if(eeprom)
 {
   Serial.println("Write Signature");
   for(i=0;i<20;i++)
   {
     Wire.beginTransmission(AT24C02B_Addr); //start
     Wire.send(address_map[i]);
     Wire.send(bugduino_signature[i]);
     Wire.endTransmission();    //stop
     delay(10);
   }
 }
 else
 {
   Serial.println("Signature OK");
 }
 for(;;);

}


</syntaxhighlight>

Example

Open the blink example Open the LED blink example sketch: File > Examples > 1.Basics > Blink.

Select your board

You'll need to select the entry in the Tools > Board menu that corresponds to your Arduino. 1.Selecting an Arduino Uno For Duemilanove Arduino boards with an ATmega328 (check the text on the chip on the board), select Arduino Duemilanove or Nano w/ ATmega328. Previously, Arduino boards came with an ATmega168; for those, select Arduino Diecimila, Duemilanove, or Nano w/ ATmega168. (Details of the board menu entries are available on the environment page.) 2.Select your serial port Select the serial device of the Arduino board from the Tools | Serial Port menu. This is likely to be COM3 or higher (COM1and COM2 are usually reserved for hardware serial ports). To find out, you can disconnect your Arduino board and re-open the menu; the entry that disappears should be the Arduino board. Reconnect the board and select that serial port.

Upload the program

Now, simply click the "Upload" button in the environment. Wait a few seconds - you should see the RX and TX leds on the board flashing. If the upload is successful, the message "Done uploading." will appear in the status bar. (Note: If you have an Arduino Mini, NG, or other board, you'll need to physically present the reset button on the board immediately before pressing the upload button.)

A few seconds after the upload finishes, you should see the pin 13 (L) LED on the board start to blink (in orange). If it does, congratulations! You've gotten Arduino up-and-running. If you have problems, please see the troubleshooting suggestions. You might also want to look at: the examples for using various sensors and actuators the reference for the Arduino language The text of the Arduino getting started guide is licensed under a Creative Commons Attribution-ShareAlike 3.0 License. Code samples in the guide are released into the public domain.


Support

If you have questions or other better design ideas, you can go to our forum or wish to discuss.


Bug Tracker

Bug Tracker is the place you can publish any bugs you think you might have found during use. Please write down what you have to say, your answers will help us improve our products.

Additional Idea

The Additional Idea is the place to write your project ideas about this product, or other usages you've found. Or you can write them on Projects page.

How to Buy

See Also

Licensing

This documentation is licensed under the Creative Commons Attribution-ShareAlike License 3.0 Source code and libraries are licensed under GPL/LGPL, see source code files for details.


External Links

Links to external webpages which provide more application ideas, documents/datasheet or software libraries