Ks0023 keyestudio 18B20 Temperature Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 19: Line 19:


==Sample Code ==
==Sample Code ==
'''OneWire Library Download:'''http://www.pjrc.com/teensy/arduino_libraries/OneWire.zip
'''OneWire Library Download:''' http://www.pjrc.com/teensy/arduino_libraries/OneWire.zip
<pre>
<pre>
#include <OneWire.h>
#include <OneWire.h>

Revision as of 14:54, 23 September 2017

18B20 Temperature Sensor


thumb


Introduction

DS18B20 is a digital temperature sensor. It can be used for quantify environmental temperature testing. The temperature range is from -55 to +125 ℃, inherent temperature resolution 0.5 ℃. It also support multi-point mesh networking. Three DS18B20 can be deployed on three lines to achieve multi-point temperature measurement. It has a 9-12 bit serial output.

Specification

  • Supply Voltage: 3.3V to 5V
  • Temperature range: -55 °C ~ +125 °C
  • Interface: Digital
  • Size: 30*20mm
  • Weight: 3g


Connection Diagram


thumb

Sample Code

OneWire Library Download: http://www.pjrc.com/teensy/arduino_libraries/OneWire.zip

#include <OneWire.h>
 int DS18S20_Pin = 2; //DS18S20 Signal pin on digital pin 2
 //Temperature chip i/o
OneWire ds(DS18S20_Pin);  // on digital pin 2
 void setup(void) {
  Serial.begin(9600);
}
 void loop(void) {
  float temperature = getTemp();
  Serial.println(temperature);
   
  delay(100); //to slow down the output so it is easier to read
   
}
 
float getTemp(){
  //returns the temperature from one DS18S20 in DEG Celsius
 
  byte data[12];
  byte addr[8];
 

  if ( !ds.search(addr)) {

      //no more sensors on chain, reset search
      ds.reset_search();
      return -1000;
  }
 
  if ( OneWire::crc8( addr, 7) != addr[7]) {
      Serial.println("CRC is not valid!");
      return -1000;
  }
 
  if ( addr[0] != 0x10 && addr[0] != 0x28) {
      Serial.print("Device is not recognized");
      return -1000;
  }
 
  ds.reset();
  ds.select(addr);
  ds.write(0x44,1); // start conversion, with parasite power on at the end
 
  byte present = ds.reset();
  ds.select(addr);    
  ds.write(0xBE); // Read Scratchpad
 
   
  for (int i = 0; i < 9; i++) { // we need 9 bytes
    data[i] = ds.read();
  }
  ds.reset_search();
   
  byte MSB = data[1];
  byte LSB = data[0];
 
  float tempRead = ((MSB << 8) | LSB); //using two's compliment
  float TemperatureSum = tempRead / 16;
   
  return TemperatureSum;
}

Resources

Video

http://www.keyestudio.com/wp/2016/05/ks0023-keyestudio-18b20-temperature-sensor/

Datasheet

http://www.keyestudio.com/files/index/download/id/1463649511/

Get One Now

http://www.keyestudio.com/keyestudio-ds18b20-temperature-sensor.html

https://www.amazon.com/Keyestudio-Temperature-Sensor-Arduino-raspberry/dp/B016ZUCMHC/ref=sr_1_3?ie=UTF8&qid=1479460234&sr=8-3&keywords=keyestudio+DS18B20+Temperature+Sensor