Ks0051 keyestudio Infrared Obstacle Avoidance Sensor: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
 
(3 intermediate revisions by the same user not shown)
Line 24: Line 24:
<br>
<br>
==Connection Diagram ==
==Connection Diagram ==
<br>[[File:Ks0051-1.png|700px|frameless|thumb]]<br>  
<br>[[File:0051.png|700px|frameless|thumb]]<br>  


<br>
<br>
==Sample Code ==
==Sample Code ==
<pre>
<pre>
const int sensorPin = 2;    // the number of the sensor pin
const int sensorPin = 3;    // the number of the sensor pin
const int ledPin =  13;      // the number of the LED pin
const int ledPin =  13;      // the number of the LED pin
int sensorState = 0;        // variable for reading the sensor status
int sensorState = 0;        // variable for reading the sensor status
Line 54: Line 54:
If we put a foam block in front of the sensor, this time when sensor detects the obstacle, sled on the sensor will be turned on.<br>
If we put a foam block in front of the sensor, this time when sensor detects the obstacle, sled on the sensor will be turned on.<br>
<br>[[File:KS0349 10-3.png|500px|frameless|thumb]]<br>
<br>[[File:KS0349 10-3.png|500px|frameless|thumb]]<br>


<br>
<br>
Line 61: Line 62:
http://video.keyestudio.com/ks0051/
http://video.keyestudio.com/ks0051/


* '''PDF'''<br>
* '''PDF and Code'''<br>
https://drive.google.com/open?id=19HbFiYtTGCL12pJj5BLl44H5_ABt_wyr
https://fs.keyestudio.com/KS0051




<br>
<br>
==Buy from==
==Buy from==



Latest revision as of 14:13, 7 January 2021


Introduction

Infrared obstacle avoidance sensor is equipped with distance adjustment function and is especially designed for wheeled robots. 
This sensor has strong adaptability to ambient light and is of high precision. It has a pair of infrared transmitting and receiving tube. When infrared ray launched by the transmitting tube encounters an obstacle (its reflector), the infrared ray is reflected to the receiving tube, and the indicator will light up; the signal output interface outputs digital signal.

We can adjust the detection distance through the potentiometer knob (effective distance: 2~40cm, working Voltage: 3.3V-5V ). 
Thanks to a wide voltage range, this sensor can work steadily even under fluctuating power supply voltage and is suitable for the use of various micro-controllers,Arduino controllers and BS2 controllers. A robot mounted with the sensor can sense changes in the environment.

thumb


Specification

  • Working voltage: DC 3.3V-5V
  • Working current: ≥20mA
  • Working temperature: -10℃ to+50℃
  • Detection distance: 2-40cm
  • IO Interface: 4 PIN (-/+/S/EN)
  • Output signal: TTL voltage
  • Accommodation mode: Multi-circle resistance regulation
  • Effective Angle: 35°


Connection Diagram


thumb


Sample Code

const int sensorPin = 3;     // the number of the sensor pin
const int ledPin =  13;      // the number of the LED pin
int sensorState = 0;         // variable for reading the sensor status
void setup() {
  pinMode(ledPin, OUTPUT);      
  pinMode(sensorPin, INPUT); }
void loop(){
  // read the state of the sensor value:
  sensorState = digitalRead(sensorPin);
  // if it is, the sensorState is HIGH:
  if (sensorState == HIGH) {     
     digitalWrite(ledPin, HIGH);  
  } 
  else {
       digitalWrite(ledPin, LOW); 
  }
}


Result

Done uploading the code to board, you can see the led on both UNO board and obstacle detector sensor is turned on.
If we put a foam block in front of the sensor, this time when sensor detects the obstacle, sled on the sensor will be turned on.

thumb



Resources

  • Video

http://video.keyestudio.com/ks0051/

  • PDF and Code

https://fs.keyestudio.com/KS0051



Buy from