Ks0121 keyestudio EASY plug Photo Interrupter Module: Difference between revisions

From Keyestudio Wiki
Jump to navigation Jump to search
Line 6: Line 6:
By emitting a beam of infrared light from one end to another end, the sensor can detect an object when it passes through the beam. <br>
By emitting a beam of infrared light from one end to another end, the sensor can detect an object when it passes through the beam. <br>
Useful for many applications such as optical limit switches, pellet dispensing, general object detection, etc.<br>
Useful for many applications such as optical limit switches, pellet dispensing, general object detection, etc.<br>
<span style="color: red">'''Note: ''' this module needs to be used together with EASY plug control board.<br>
This module needs to be used together with EASY plug control board.<br>
 
 
<span style=color:red> '''Special Note:''' <br>
The sensor/module is equiped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board  with RJ11 6P6C interface. <br> If you have the control board of other brands, it is also equiped with the RJ11 6P6C interface but have different internal line sequence, can not be used compatibly with our sensor/module. </span><br>
 
<br>
<br>



Revision as of 08:53, 22 May 2019

Keyestudio EASY plug Photo Interrupter Module

Introduction

This is a high performance EASY Plug photo interrupter module.
The upright part on the module combines an infrared light emitting diode and shielded infrared detector.
By emitting a beam of infrared light from one end to another end, the sensor can detect an object when it passes through the beam.
Useful for many applications such as optical limit switches, pellet dispensing, general object detection, etc.
This module needs to be used together with EASY plug control board.


Special Note:
The sensor/module is equiped with the RJ11 6P6C interface, compatible with our keyestudio EASY plug Control Board with RJ11 6P6C interface.
If you have the control board of other brands, it is also equiped with the RJ11 6P6C interface but have different internal line sequence, can not be used compatibly with our sensor/module.


Specification

  • Connector: Easy plug
  • Supply Voltage: 3.3V to 5V
  • Interface: Digital


Technical Details

  • Dimensions: 38mm*20mm*18mm
  • Weight: 4.8g


Connect It Up

Connect the EASY Plug Photo Interrupter module and LED module to control board using RJ11 cables. Then connect the control board to your PC with a USB cable.
thumb

Upload the Code

Below is an example code. Open or drag below code to Mixly Blocks and upload.

thumb


What You Should See

Done uploading the code, powered on, if pick up a piece of paper to cover the light on the groove part of module, you should see the LED is turned on. If no interruption, the LED is off.

thumb

thumb



Extension Experiment

Adding 4-digit LED Display


Hookup Guide
Connect the EASY Plug crash sensor, 4-digit LED display and LED module to control board using RJ11 cables.

thumb


Upload the Code
Below is an example code.

thumb

thumb


What You Should See

thumb

Done uploading the code, if pick up a piece of paper to cover the light on the groove part, the LED is turned on. If no interruption, the LED is off.
thumb
You should be able to see the number of covering the light is showed on the 4-digit LED display, or on the monitor.
thumb



Resources

Download the Arduino Datasheet:
https://drive.google.com/open?id=1bUzBV5--XSbR5vWkbP1shRLCVHCnZW3j

Download the Mixly Code and PDF:
https://drive.google.com/open?id=1zTJzCmowa5YxaQNBA_qTRAN3bHRXSo4i



Buy from